[PATCH v2 11/12] ARM: nxp-imx8mq-evk: Add bootflow comments

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add some notes on how the boot-flow goes while I still remember it.

Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
---
 arch/arm/boards/nxp-imx8mq-evk/lowlevel.c | 41 +++++++++++++++++++++--
 1 file changed, 39 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boards/nxp-imx8mq-evk/lowlevel.c b/arch/arm/boards/nxp-imx8mq-evk/lowlevel.c
index db746bb94..fdc964ac9 100644
--- a/arch/arm/boards/nxp-imx8mq-evk/lowlevel.c
+++ b/arch/arm/boards/nxp-imx8mq-evk/lowlevel.c
@@ -66,6 +66,26 @@ static void nxp_imx8mq_evk_sram_setup(void)
 	BUG_ON(ret);
 }
 
+/*
+ * Power-on execution flow of start_nxp_imx8mq_evk() might not be
+ * obvious for a very frist read, so here's, hopefully helpful,
+ * summary:
+ *
+ * 1. MaskROM uploads PBL into OCRAM and that's where this function is
+ *    executed for the first time
+ *
+ * 2. DDR is initialized and full i.MX image is loaded to the
+ *    beginning of RAM
+ *
+ * 3. start_nxp_imx8mq_evk, now in RAM, is executed again
+ *
+ * 4. BL31 blob is uploaded to OCRAM and the control is transfer to it
+ *
+ * 5. BL31 exits EL3 into EL2 at address MX8MQ_ATF_BL33_BASE_ADDR,
+ *    executing start_nxp_imx8mq_evk() the third time
+ *
+ * 6. Standard barebox boot flow continues
+ */
 ENTRY_FUNCTION(start_nxp_imx8mq_evk, r0, r1, r2)
 {
 	arm_cpu_lowlevel_init();
@@ -73,9 +93,23 @@ ENTRY_FUNCTION(start_nxp_imx8mq_evk, r0, r1, r2)
 	if (IS_ENABLED(CONFIG_DEBUG_LL))
 		setup_uart();
 
-	if (get_pc() < MX8MQ_DDR_CSD1_BASE_ADDR)
+	if (get_pc() < MX8MQ_DDR_CSD1_BASE_ADDR) {
+		/*
+		 * We assume that we were just loaded by MaskROM into
+		 * SRAM if we are not running from DDR. We also assume
+		 * that means DDR needs to be initialized for the
+		 * first time.
+		 */
 		nxp_imx8mq_evk_sram_setup();
-
+	}
+	/*
+	 * Straight from the power-on we are at EL3, so the following
+	 * code _will_ load and jump to ATF.
+	 *
+	 * However when we are re-executed upon exit from ATF's
+	 * initialization routine, it is EL2 which means we'll skip
+	 * loadting ATF blob again
+	 */
 	if (current_el() == 3) {
 		const u8 *bl31;
 		size_t bl31_size;
@@ -84,6 +118,9 @@ ENTRY_FUNCTION(start_nxp_imx8mq_evk, r0, r1, r2)
 		imx8mq_atf_load_bl31(bl31, bl31_size);
 	}
 
+	/*
+	 * Standard entry we hit once we initialized both DDR and ATF
+	 */
 	barebox_arm_entry(MX8MQ_DDR_CSD1_BASE_ADDR,
 			  SZ_2G + SZ_1G, __dtb_imx8mq_evk_start);
 }
-- 
2.17.1


_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux