On 01/24/2019 01:30 AM, Thiago Ramon wrote:
Back again with more info.
I've done a dump-tree on my array, and from the 71GB of tree data,
I've only got the following errors:
parent transid verify failed on 31288448466944 wanted 135681 found 135575
parent transid verify failed on 31288448466944 wanted 135681 found 135575
checksum verify failed on 31288448466944 found 9D027AC2 wanted 79E1C774
checksum verify failed on 31288448466944 found 9A1BA23D wanted CFE05F82
checksum verify failed on 31288448466944 found 9A1BA23D wanted CFE05F82
bad tree block 31288448466944, bytenr mismatch, want=31288448466944,
have=198834197030656
failed to read 31288448466944 in tree 2
parent transid verify failed on 31288448483328 wanted 135681 found 135575
parent transid verify failed on 31288448483328 wanted 135681 found 135575
checksum verify failed on 31288448483328 found D1816F8A wanted 3562D23C
checksum verify failed on 31288448483328 found 51B89701 wanted EECC5745
checksum verify failed on 31288448483328 found 51B89701 wanted EECC5745
bad tree block 31288448483328, bytenr mismatch, want=31288448483328,
have=198834197025536
failed to read 31288448483328 in tree 2
parent transid verify failed on 17412886069248 wanted 31316 found 31040
parent transid verify failed on 17412886069248 wanted 31316 found 31040
checksum verify failed on 17412886069248 found 5A0CE056 wanted BEEF5DE0
checksum verify failed on 17412886069248 found 52BE5880 wanted A8702E6B
checksum verify failed on 17412886069248 found 5A0CE056 wanted BEEF5DE0
bad tree block 17412886069248, bytenr mismatch, want=17412886069248, have=0
failed to read 17412886069248 in tree 7
If there are sufficient mirror parent transit verify failed should
follow with errors-fixed logs.
I wonder what type of chunks are these.
'btrfs fi df <mnt>'
Thanks.
If I'm reading this correctly, it's just a couple bad nodes in the
extent tree and one in the checksum tree (assuming they aren't hiding
lost nodes behind them). Would it be possible to manually fix those
nodes, and if so, how should I proceed? (I have experience in
data-recovery on other filesystems, but my knowledge of BTRFS isn't
deep enough yet to allow me to even guess where I should start poking,
so any pointers are welcome)
And thanks again for all help so far
On Tue, Jan 22, 2019 at 9:28 PM Thiago Ramon <thiagoramon@xxxxxxxxx> wrote:
On Tue, Jan 22, 2019 at 6:43 PM Chris Murphy <lists@xxxxxxxxxxxxxxxxx> wrote:
On Tue, Jan 22, 2019 at 9:41 AM Thiago Ramon <thiagoramon@xxxxxxxxx> wrote:
Back again with pretty much the same problem, but now without a
reasonable cause:
I've bought a couple new 8TB disks, recovered everything I needed from
my previously damaged FS to a new BTRFS on those 2 drives (single copy
mode), double-checked if everything was fine, then wipefs'd the old
disks and added the ones that didn't have any issues previously to the
new array and rebalanced to RAID6.
Everything was running fine through the weekend and I was about 50%
done when today:
[ +7.733525] BTRFS info (device bcache0): relocating block group
8358036766720 flags data
[Jan22 09:20] BTRFS warning (device bcache0): bcache0 checksum verify
failed on 31288448499712 wanted A3746F78 found 44D6AEB0 level 1
[ +0.460086] BTRFS info (device bcache0): read error corrected: ino 0
off 31288448499712 (dev /dev/bcache4 sector 7401171296)
[ +0.000199] BTRFS info (device bcache0): read error corrected: ino 0
off 31288448503808 (dev /dev/bcache4 sector 7401171304)
[ +0.000181] BTRFS info (device bcache0): read error corrected: ino 0
off 31288448507904 (dev /dev/bcache4 sector 7401171312)
[ +0.000158] BTRFS info (device bcache0): read error corrected: ino 0
off 31288448512000 (dev /dev/bcache4 sector 7401171320)
This is corruption being detected and corrected on those listed
sectors. As this is a bcache device, it's a virtual sector so it's
hard to tell if it's coming from bcache itself, or the cache device,
or the backing device.
I was using bcache in writeback mode with my old FS, but I've learned
THAT lesson the hard way. This one was just using writearound, unless
bcache REALLY screwed it up I find it hard that it's the source of the
corruption. There were no read or write errors from bcache since the
time the new array went up, and each bcache* device is just a thin
layer over a whole raw disk now.
[Jan22 09:21] BTRFS info (device bcache0): found 2050 extents
[ +8.055456] BTRFS info (device bcache0): found 2050 extents
[Jan22 09:22] BTRFS info (device bcache0): found 2050 extents
[ +0.846627] BTRFS info (device bcache0): relocating block group
8356963024896 flags data
[Jan22 09:23] BTRFS info (device bcache0): found 2052 extents
[ +6.983072] BTRFS info (device bcache0): found 2052 extents
[ +0.844419] BTRFS info (device bcache0): relocating block group
8355889283072 flags data
[ +33.906101] BTRFS info (device bcache0): found 2058 extents
[ +4.664570] BTRFS info (device bcache0): found 2058 extents
[Jan22 09:24] BTRFS info (device bcache0): relocating block group
8354815541248 flags data
[Jan22 09:25] BTRFS info (device bcache0): found 2057 extents
[ +17.650586] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
Over 100 generations have passed, and yet it's only finding stale data
on the desired btrfs byte nr (in btrfs linear space) so it might be
extent tree corruption again.
It's not possible from the available information to do anything but
speculate how that much data is being lost or somehow being
overwritten.
[ +0.088917] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
[ +0.001381] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
[ +0.003555] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
[ +0.005478] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
[ +0.003953] BTRFS error (device bcache0): parent transid verify
failed on 31288448466944 wanted 135681 found 135575
[ +0.000917] BTRFS: error (device bcache0) in
btrfs_run_delayed_refs:3013: errno=-5 IO failure
[ +0.000017] BTRFS: error (device bcache0) in
btrfs_drop_snapshot:9463: errno=-5 IO failure
And -5 I/O error is not a Btrfs error either, it's the detection of an
IO error from the underlying block device, whether real or virtual.
Couldn't figure the source of the -5 either, no kernel logs from
anything byt BTRFS complaining about it. After I umounted the array,
it didn't shown up anymore, and I was able to remount the array with
the skip_bg patch.
[ +0.000895] BTRFS info (device bcache0): forced readonly
[ +0.000902] BTRFS: error (device bcache0) in merge_reloc_roots:2429:
errno=-5 IO failure
[ +0.000387] BTRFS info (device bcache0): balance: ended with status: -30
Couldn't check anything even in RO mode scrub or btrfs check, when I
unmounted the array I got a few kernel stack traces:
[Jan22 13:58] WARNING: CPU: 3 PID: 9711 at fs/btrfs/extent-tree.c:5986
btrfs_free_block_groups+0x395/0x3b0 [btrfs]
[ +0.000032] CPU: 3 PID: 9711 Comm: umount Not tainted
4.20.0-042000-generic #201812232030
[ +0.000001] Hardware name: Gigabyte Technology Co., Ltd. To be
filled by O.E.M./H61M-DS2H, BIOS F6 12/14/2012
[ +0.000014] RIP: 0010:btrfs_free_block_groups+0x395/0x3b0 [btrfs]
[ +0.000002] Code: 01 00 00 00 0f 84 a0 fe ff ff 0f 0b 48 83 bb d0 01
00 00 00 0f 84 9e fe ff ff 0f 0b 48 83 bb 08 0$
00 00 00 0f 84 9c fe ff ff <0f> 0b 48 83 bb 00 02 00 00 00 0f 84 9a
fe ff ff 0f 0b e9 93 fe ff
[ +0.000001] RSP: 0018:ffffa3c1c2997d88 EFLAGS: 00010206
[ +0.000001] RAX: 0000000020000000 RBX: ffff924aae380000 RCX:
0000000000000000
[ +0.000001] RDX: ffffffffe0000000 RSI: ffff924b85970600 RDI:
ffff924b85970600
[ +0.000001] RBP: ffffa3c1c2997db8 R08: 0000000020000000 R09:
ffff924b859706a8
[ +0.000000] R10: 0000000000000002 R11: ffff924b973a1c04 R12:
ffff924aae380080
[ +0.000001] R13: ffff924b8dfe8400 R14: ffff924aae380090 R15:
0000000000000000
[ +0.000002] FS: 00007f1bd1076080(0000) GS:ffff924b97380000(0000)
knlGS:0000000000000000
[ +0.000001] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000000] CR2: 0000562d2eb13c10 CR3: 0000000156910006 CR4:
00000000001606e0
[ +0.000001] Call Trace:
[ +0.000018] close_ctree+0x143/0x2e0 [btrfs]
[ +0.000012] btrfs_put_super+0x15/0x20 [btrfs]
[ +0.000004] generic_shutdown_super+0x72/0x110
[ +0.000001] kill_anon_super+0x18/0x30
[ +0.000012] btrfs_kill_super+0x16/0xa0 [btrfs]
[ +0.000002] deactivate_locked_super+0x3a/0x80
[ +0.000001] deactivate_super+0x51/0x60
[ +0.000003] cleanup_mnt+0x3f/0x80
[ +0.000001] __cleanup_mnt+0x12/0x20
[ +0.000002] task_work_run+0x9d/0xc0
[ +0.000002] exit_to_usermode_loop+0xf2/0x100
[ +0.000002] do_syscall_64+0xda/0x110
[ +0.000003] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ +0.000001] RIP: 0033:0x7f1bd14bae27
[ +0.000001] Code: 90 0c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44
00 00 31 f6 e9 09 00 00 00 66 0f 1f 84 00 00 00
00 00 b8 a6 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 39
90 0c 00 f7 d8 64 89 01 48
[ +0.000001] RSP: 002b:00007ffdb15a75a8 EFLAGS: 00000246 ORIG_RAX:
00000000000000a6
[ +0.000002] RAX: 0000000000000000 RBX: 000055df329eda40 RCX:
00007f1bd14bae27
[ +0.000000] RDX: 0000000000000001 RSI: 0000000000000000 RDI:
000055df329edc20
[ +0.000001] RBP: 0000000000000000 R08: 000055df329eea70 R09:
00000000ffffffff
[ +0.000001] R10: 000000000000000b R11: 0000000000000246 R12:
000055df329edc20
[ +0.000001] R13: 00007f1bd15e18c4 R14: 0000000000000000 R15:
00007ffdb15a7818
Now I'm back in a very similar situation as before, btrfs check gets me:
Opening filesystem to check...
checksum verify failed on 24707469082624 found 451E87BF wanted
A1FD3A09
checksum verify failed on 24707469082624 found 2C2AEBE0 wanted
D6652D6A
checksum verify failed on 24707469082624 found 2C2AEBE0 wanted
D6652D6A
bad tree block 24707469082624, bytenr mismatch, want=24707469082624,
have=231524568072192
Couldn't read tree root
ERROR: cannot open file system
I could do it all again, but first, what can be wrong here? This array
was working for some 4 years until it went bad a few weeks ago, and
now the FS got badly corrupted again without any warnings. Any
suggestions? Bad RAM, SAS controller going bad, some weirdly behaving
disk? I need to figure out what can be failing before I try another
recovery.
I think it's specifically storage stack related. I think you'd have
more varied and weird problems if it were memory corruption, but
that's speculation on my part.
I've done a quick memory test with stressapptest and it was fine, so
if it's the memory it's something very localized.
I'd honestly simplify the layout and not use bcache at all, only use
Btrfs directly on the whole drives, although I think it's reasonably
simple to use dmcrypt if needed/desired. But it's still better for
troubleshooting to make the storage stack as simple as possible.
Without more debugging information from all the layers, it's hard to
tell which layer to blame without just using the big stick called
process of elimination.
Maybe Qu has some ideas based on the call trace though - I can't parse it.
--
Chris Murphy
