---------------------------------------- > To: linux-btrfs@xxxxxxxxxxxxxxx > From: samtygier@xxxxxxxxxxx > Subject: Re: problem replacing failing drive > Date: Thu, 25 Oct 2012 22:02:23 +0100 > > On 22/10/12 10:07, sam tygier wrote: > > hi, > > > > I have a 2 drive btrfs raid set up. It was created first with a single drive, and then adding a second and doing > > btrfs fi balance start -dconvert=raid1 /data > > > > the original drive is showing smart errors so i want to replace it. i dont easily have space in my desktop for an extra disk, so i decided to proceed by shutting down. taking out the old failing drive and putting in the new drive. this is similar to the description at > > https://btrfs.wiki.kernel.org/index.php/Using_Btrfs_with_Multiple_Devices#Replacing_Failed_Devices > > (the other reason to try this is to simulate what would happen if a drive did completely fail). > > > > so after swapping the drives and rebooting, i try to mount as degraded. i instantly get a kernel panic, http://www.hep.man.ac.uk/u/sam/pub/IMG_5397_crop.png > > > > so far all this has been with 3.5 kernel. so i upgraded to 3.6.2 and tried to mount degraded again. > > > > first with just sudo mount /dev/sdd2 /mnt, then with sudo mount -o degraded /dev/sdd2 /mnt > > > > [ 582.535689] device label bdata devid 1 transid 25342 /dev/sdd2 > > [ 582.536196] btrfs: disk space caching is enabled > > [ 582.536602] btrfs: failed to read the system array on sdd2 > > [ 582.536860] btrfs: open_ctree failed > > [ 606.784176] device label bdata devid 1 transid 25342 /dev/sdd2 > > [ 606.784647] btrfs: allowing degraded mounts > > [ 606.784650] btrfs: disk space caching is enabled > > [ 606.785131] btrfs: failed to read chunk root on sdd2 > > [ 606.785331] btrfs warning page private not zero on page 3222292922368 > > [ 606.785408] btrfs: open_ctree failed > > [ 782.422959] device label bdata devid 1 transid 25342 /dev/sdd2 > > > > no panic is good progress, but something is still not right. > > > > my options would seem to be > > 1) reconnect old drive (probably in a USB caddy), see if it mounts as if nothing ever happened. or possibly try and recover it back to a working raid1. then try again with adding the new drive first, then removing the old one. > > 2) give up experimenting and create a new btrfs raid1, and restore from backup > > > > both leave me with a worry about what would happen if a disk in a raid 1 did die. (unless is was the panic that did some damage that borked the filesystem.) > > Some more details. > > If i reconnect the failing drive then I can mount the filesystem with no errors, a quick glance suggests that the data is all there. > > Label: 'bdata' uuid: 1f07081c-316b-48be-af73-49e6f76535cc > Total devices 2 FS bytes used 2.50TB > devid 2 size 2.73TB used 2.73TB path /dev/sde1 <-- this is the drive that i wish to remove > devid 1 size 2.73TB used 2.73TB path /dev/sdd2 > > sudo btrfs filesystem df /mnt > Data, RAID1: total=2.62TB, used=2.50TB > System, DUP: total=40.00MB, used=396.00KB > System: total=4.00MB, used=0.00 > Metadata, DUP: total=112.00GB, used=3.84GB > Metadata: total=8.00MB, used=0.00 > > is the failure to mount when i remove sde due to it being dup, rather than raid1? Yes, I would say so. Try a btrfs balance start -mconvert=raid1 /mnt so all metadata is on each drive. > > is adding a second drive to a btrfs filesystem and running > btrfs fi balance start -dconvert=raid1 /mnt > not sufficient to create an array that can survive the loss of a disk? do i need -mconvert as well? is there an -sconvert for system? > > thanks > > Sam > > > -- > To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-btrfs" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
