Re: pinnacle pctv, can't tune since 2.6.10 (reverting bttv to 2.6.9's version fixes problem) | |
| [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] | |
It was exactly the same problem for me, my card works perfectly under 2.6.9 Thanks, FX Le Dimanche 30 Janvier 2005 17:10, Mickael Marchand a écrit : > hmm forgot some more infos : > > dmesg : > Jan 30 05:51:29 localhost kernel: bttv: driver version 0.9.15 loaded > Jan 30 05:51:29 localhost kernel: bttv: using 8 buffers with 2080k (520 > pages) each for capture > Jan 30 05:51:29 localhost kernel: bttv: Bt8xx card found (0). > Jan 30 05:51:29 localhost kernel: ACPI: PCI interrupt 0000:00:0c.0[A] -> > GSI 17 (level, low) -> IRQ 185 > Jan 30 05:51:29 localhost kernel: bttv0: Bt878 (rev 17) at 0000:00:0c.0, > irq: 185, latency: 64, mmio: 0xf4b00000 > Jan 30 05:51:29 localhost kernel: bttv0: detected: Pinnacle PCTV > [card=39], PCI subsystem ID is 11bd:0012 > Jan 30 05:51:29 localhost kernel: bttv0: using: Pinnacle PCTV > Studio/Rave [card=39,autodetected] > Jan 30 05:51:29 localhost kernel: bttv0: i2c: checking for MSP34xx @ > 0x80... not found > Jan 30 05:51:29 localhost kernel: bttv0: pinnacle/mt: id=4 > info="PAL+SECAM / mono" radio=no > Jan 30 05:51:29 localhost kernel: bttv0: using tuner=33 > Jan 30 05:51:29 localhost kernel: bttv0: i2c: checking for MSP34xx @ > 0x80... not found > Jan 30 05:51:29 localhost kernel: bttv0: i2c: checking for TDA9875 @ > 0xb0... not found > Jan 30 05:51:29 localhost kernel: bttv0: i2c: checking for TDA7432 @ > 0x8a... not found > Jan 30 05:51:29 localhost kernel: tda9885/6/7: chip found @ 0x86 > Jan 30 05:51:29 localhost kernel: tuner: chip found at addr 0xc0 i2c-bus > bt878 #0 [sw] > Jan 30 05:51:29 localhost kernel: tuner: type set to 33 (MT20xx > universal) by bt878 #0 [sw] > Jan 30 05:51:29 localhost kernel: tuner: microtune: companycode=4d54 > part=04 rev=04 > Jan 30 05:51:29 localhost kernel: tuner: microtune MT2032 found, OK > Jan 30 05:51:29 localhost kernel: bttv0: registered device video0 > Jan 30 05:51:29 localhost kernel: bttv0: registered device vbi0 > Jan 30 05:51:29 localhost kernel: bttv0: PLL: 28636363 => 35468950 .. ok > > > > and just saw that in my syslog : > Jan 30 06:39:12 localhost kernel: tuner: TV freq (268435455.93) out of > range (44-958) > Jan 30 06:39:49 localhost kernel: mt2032_set_if_freq failed with -121 > Jan 30 06:39:50 localhost kernel: mt2032_set_if_freq2 failed with -121 > Jan 30 06:39:50 localhost kernel: mt2032_set_if_freq failed with -121 > Jan 30 06:39:50 localhost kernel: mt2032_set_if_freq2 failed with -121 > Jan 30 06:39:51 localhost kernel: mt2032_set_if_freq failed with -121 > Jan 30 06:39:51 localhost kernel: mt2032_set_if_freq2 failed with -121 > Jan 30 06:39:53 localhost kernel: bttv0: timeout: drop=45 irq=2834/2876, > risc=2bb4002c, bits: HSYNC OFLOW FDSR > > Mik > > Mickael Marchand wrote: > > Hi, > > > > I have the following card (using it in France , SECAM) : > > 0000:00:0c.0 Multimedia video controller: Brooktree Corporation Bt878 > > Video Capture (rev 11) > > Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo > > receiver) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 64 (4000ns min, 10000ns max) > > Interrupt: pin A routed to IRQ 185 > > Region 0: Memory at f4b00000 (32-bit, prefetchable) [size=4K] > > Capabilities: [44] Vital Product Data > > Capabilities: [4c] Power Management version 2 > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > 0000:00:0c.1 Multimedia controller: Brooktree Corporation Bt878 Audio > > Capture (rev 11) > > Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo > > receiver, audio section) > > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > > ParErr- Stepping- SERR+ FastB2B- > > Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > > <TAbort- <MAbort- >SERR- <PERR- > > Latency: 64 (1000ns min, 63750ns max) > > Interrupt: pin A routed to IRQ 185 > > Region 0: Memory at f4c00000 (32-bit, prefetchable) [size=4K] > > Capabilities: [44] Vital Product Data > > Capabilities: [4c] Power Management version 2 > > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > > PME(D0-,D1-,D2-,D3hot-,D3cold-) > > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > > > since 2.6.10 (till 2.6.11-rc2-mm2 tested last night), I can't change > > channels in any tv application. > > dmesg shows things like : > > Jan 30 06:03:55 localhost kernel: mt2032_set_if_freq failed with -121 > > Jan 30 06:03:56 localhost kernel: mt2032_set_if_freq2 failed with -121 > > Jan 30 06:03:56 localhost kernel: mt2032_set_if_freq failed with -121 > > > > I have heard that other french people has the same problem and also saw > > someone with a similar bug a few days ago on this list (with a mt2050 > > this time). > > > > I've hacked a 2.6.10 to work by reverting all bttv's related changes > > between 2.6.9 and 2.6.10, so it seems the bug have been introduced > > between these 2 kernels. > > > > I'll be pleased to test any proposed patch, I already looked quite a lot > > at the patch I used to revert the changes but was not able to find the > > reason of the bug ... > > > > Cheers, > > Mik > > > > -- > > > > Unsubscribe > > mailto:video4linux-list-request@xxxxxxxxxx?subject=unsubscribe > > https://www.redhat.com/mailman/listinfo/video4linux-list > > -- > > Unsubscribe mailto:video4linux-list-request@xxxxxxxxxx?subject=unsubscribe > https://www.redhat.com/mailman/listinfo/video4linux-list -- Unsubscribe mailto:video4linux-list-request@xxxxxxxxxx?subject=unsubscribe https://www.redhat.com/mailman/listinfo/video4linux-list
|
