device descriptor read/8, error -110 | |
| [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] | |
I'm having problems with a Hauppauge Nova-T USB 2.0 stick on an SIS USB Hostcontroller (Asus Pundit barebone): Loading the module ehci_hcd with the stick plugged in leads to failures when the stick has not yet been initialized: [...]usb 1-1: new high speed USB device using ehci_hcd and address 3usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110[...] When I unplug the stick and replug it AFTER the ehci_hcd is loaded everything is fine - the stick is detected in "cold state", the firmware is load up and everything works fine. When I unload ehci_hcd after the stick has been initialized and reload ehci_hcd again the stick is identified correctly and works fine. When I unload ehci_hcd (not usbcore!), replug the stick and reload ehci_hcd the stick is uninitialized again and I've got the error messages again! I tried several kernel versions (at the moment I'm using 2.6.21.1) with several boot/module options (acpi=off, noapic, usbcore: use_old_scheme_first=y) and the different USB slots but I always get the same behavior. When I try a different USB Controller (PCMCIA USB controller) everything works fine, so its not a general problem with the stick! But for optical reasons using the PCMCIA USB controller is no option for me. And there are no free PCI slots - I cannot connect a PCI controller :( Since I use this PC as a VCR it would be nice if I hadn't to replug the stick manually after every reboot ;) One more thing to mention: when ohci_hcd is loaded I get the same problems - but this time from ohci_hcd. Replugging the stick leads to a correct identification but the the ohci driver complains that this is a USB 2.0 only device. Do you have any ideas what might be wrong here? Many thanks in advance, Olaf extract of lspci:00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)00:03.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0 Controller (rev 0f)00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller cat /proc/interrupts: CPU0 0: 62 IO-APIC-edge timer 1: 777 IO-APIC-edge i8042 7: 0 IO-APIC-edge parport0 8: 1 IO-APIC-edge rtc 14: 4074 IO-APIC-edge ide0 16: 1 IO-APIC-fasteoi yenta 17: 22540 IO-APIC-fasteoi ehci_hcd:usb1 18: 379342 IO-APIC-fasteoi saa7146 (0) 19: 15824 IO-APIC-fasteoi saa7146 (1) 20: 1 IO-APIC-fasteoi acpiNMI: 0LOC: 122518ERR: 0MIS: 0 Here are the kernel logs:Attention: there is a WLAN USB Adapter plugged in, too (Asus) three extracts follow:1. loading ehci_hcd with the uninitialized stick plugged in2. replugging the stick3. loading ehci_hcd with the initialized stick pluggin in **** loading ehci_hcd with the uninitialized stick plugged in: ****ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 17ehci_hcd 0000:00:03.3: EHCI Host Controllerdrivers/usb/core/inode.c: creating file 'devices'drivers/usb/core/inode.c: creating file '001'ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024PCI: cache line size of 128 is not supported by device 0000:00:03.3ehci_hcd 0000:00:03.3: supports USB remote wakeupehci_hcd 0000:00:03.3: irq 17, io mem 0xdd000000ehci_hcd 0000:00:03.3: reset command 010002 (park)=0 ithresh=1 period=1024 Reset HALTehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024 RUNehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004usb usb1: default language 0x0409usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1usb usb1: Product: EHCI Host Controllerusb usb1: Manufacturer: Linux 2.6.22.1 ehci_hcdusb usb1: SerialNumber: 0000:00:03.3usb usb1: ueventusb usb1: usb_probe_deviceusb usb1: configuration #1 chosen from 1 choiceusb usb1: adding 1-0:1.0 (config #1, interface 0)usb 1-0:1.0: ueventusb 1-0:1.0: ueventhub 1-0:1.0: usb_probe_interfacehub 1-0:1.0: usb_probe_interface - got idhub 1-0:1.0: USB hub foundhub 1-0:1.0: 6 ports detectedhub 1-0:1.0: standalone hubhub 1-0:1.0: no power switching (usb 1.0)hub 1-0:1.0: individual port over-current protectionhub 1-0:1.0: Single TThub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)hub 1-0:1.0: power on to power good time: 20mshub 1-0:1.0: local power source is goodhub 1-0:1.0: trying to enable port power on non-switchable hubdrivers/usb/core/inode.c: creating file '001'hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000ehci_hcd 0000:00:03.3: GetStatus port 1 status 001803 POWER sig=j CSC CONNECThub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/shub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: new high speed USB device using ehci_hcd and address 2usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: new high speed USB device using ehci_hcd and address 3usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110usb 1-1: khubd timed out on ep0in len=0/8usb 1-1: device descriptor read/8, error -110ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: new high speed USB device using ehci_hcd and address 4usb 1-1: khubd timed out on ep0in len=0/64usb 1-1: khubd timed out on ep0in len=0/64usb 1-1: khubd timed out on ep0in len=0/64ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: device descriptor read/64, error -110usb 1-1: khubd timed out on ep0in len=0/64usb 1-1: khubd timed out on ep0in len=0/64usb 1-1: khubd timed out on ep0in len=0/64ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: device descriptor read/64, error -110ehci_hcd 0000:00:03.3: port 1 full speed --> companionehci_hcd 0000:00:03.3: GetStatus port 1 status 003801 POWER OWNER sig=j CONNECThub 1-0:1.0: port 1 not reset yet, waiting 50msehci_hcd 0000:00:03.3: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSCehci_hcd 0000:00:03.3: GetStatus port 2 status 001803 POWER sig=j CSC CONNECThub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/shub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:03.3: port 2 high speedehci_hcd 0000:00:03.3: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECTusb 1-2: new high speed USB device using ehci_hcd and address 6usb 1-2: default language 0x0409usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0usb 1-2: Product: 802.11g WLAN Driveusb 1-2: Manufacturer: ASUSusb 1-2: ueventusb 1-2: usb_probe_deviceusb 1-2: configuration #1 chosen from 1 choiceusb 1-2: adding 1-2:1.0 (config #1, interface 0)usb 1-2:1.0: ueventusb 1-2:1.0: ueventndiswrapper 1-2:1.0: usb_probe_interfacendiswrapper 1-2:1.0: usb_probe_interface - got idehci_hcd 0000:00:03.3: port 2 high speedehci_hcd 0000:00:03.3: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECTusb 1-2: reset high speed USB device using ehci_hcd and address 6ndiswrapper: driver rt2500usb (Ralink,10/17/2005, 2.01.00.0000) loadedusb_endpoint usbdev1.6_ep81: ep_device_release called for usbdev1.6_ep81usb_endpoint usbdev1.6_ep01: ep_device_release called for usbdev1.6_ep01wlan0: ethernet device 00:17:31:af:3a:ab using NDIS driver: rt2500usb, version: 0x20000, NDIS version: 0x500, vendor: 'Ralink Technology Inc.', 0B05:1706.F.confwlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSKdrivers/usb/core/inode.c: creating file '006'hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0002 **** replugging the stick: ****ehci_hcd 0000:00:03.3: GetStatus port 1 status 001803 POWER sig=j CSC CONNECThub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/shub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: new high speed USB device using ehci_hcd and address 3usb 1-1: default language 0x0409usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3usb 1-1: Product: Nova-T Stickusb 1-1: Manufacturer: Hauppaugeusb 1-1: SerialNumber: 0000000000usb 1-1: ueventusb 1-1: usb_probe_deviceusb 1-1: configuration #1 chosen from 1 choiceusb 1-1: adding 1-1:1.0 (config #1, interface 0)usb 1-1:1.0: ueventusb 1-1:1.0: ueventndiswrapper 1-1:1.0: usb_probe_interfacendiswrapper 1-1:1.0: usb_probe_interface - got iddvb_usb_dib0700 1-1:1.0: usb_probe_interfacedvb_usb_dib0700 1-1:1.0: usb_probe_interface - got iddvb-usb: found a 'Hauppauge Nova-T Stick' in cold state, will try to load a firmwaredvb-usb: downloading firmware from file 'dvb-usb-dib0700-01.fw'dib0700: firmware started successfully.dvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.DVB: registering new adapter (Hauppauge Nova-T Stick).DVB: registering frontend 2 (DiBcom 7000MA/MB/PA/PB/MC)...MT2060: successfully identified (IF1 = 1220)dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.drivers/usb/core/inode.c: creating file '003' **** loading ehci_hcd with the initialized stick pluggin in: ****ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 17ehci_hcd 0000:00:03.3: EHCI Host Controllerdrivers/usb/core/inode.c: creating file 'devices'drivers/usb/core/inode.c: creating file '001'ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1ehci_hcd 0000:00:03.3: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6ehci_hcd 0000:00:03.3: reset hcc_params 7070 thresh 7 uframes 1024PCI: cache line size of 128 is not supported by device 0000:00:03.3ehci_hcd 0000:00:03.3: supports USB remote wakeupehci_hcd 0000:00:03.3: irq 17, io mem 0xdd000000ehci_hcd 0000:00:03.3: reset command 010002 (park)=0 ithresh=1 period=1024 Reset HALTehci_hcd 0000:00:03.3: init command 010001 (park)=0 ithresh=1 period=1024 RUNehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004usb usb1: default language 0x0409usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1usb usb1: Product: EHCI Host Controllerusb usb1: Manufacturer: Linux 2.6.22.1 ehci_hcdusb usb1: SerialNumber: 0000:00:03.3usb usb1: ueventusb usb1: usb_probe_deviceusb usb1: configuration #1 chosen from 1 choiceusb usb1: adding 1-0:1.0 (config #1, interface 0)usb 1-0:1.0: ueventusb 1-0:1.0: ueventhub 1-0:1.0: usb_probe_interfacehub 1-0:1.0: usb_probe_interface - got idhub 1-0:1.0: USB hub foundhub 1-0:1.0: 6 ports detectedhub 1-0:1.0: standalone hubhub 1-0:1.0: no power switching (usb 1.0)hub 1-0:1.0: individual port over-current protectionhub 1-0:1.0: Single TThub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)hub 1-0:1.0: power on to power good time: 20mshub 1-0:1.0: local power source is goodhub 1-0:1.0: trying to enable port power on non-switchable hubdrivers/usb/core/inode.c: creating file '001'hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000ehci_hcd 0000:00:03.3: GetStatus port 1 status 001803 POWER sig=j CSC CONNECThub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/shub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:03.3: port 1 high speedehci_hcd 0000:00:03.3: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECTusb 1-1: new high speed USB device using ehci_hcd and address 2usb 1-1: default language 0x0409usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3usb 1-1: Product: Nova-T Stickusb 1-1: Manufacturer: Hauppaugeusb 1-1: SerialNumber: 0000000000usb 1-1: ueventusb 1-1: usb_probe_deviceusb 1-1: configuration #1 chosen from 1 choiceusb 1-1: adding 1-1:1.0 (config #1, interface 0)usb 1-1:1.0: ueventusb 1-1:1.0: ueventndiswrapper 1-1:1.0: usb_probe_interfacendiswrapper 1-1:1.0: usb_probe_interface - got iddvb_usb_dib0700 1-1:1.0: usb_probe_interfacedvb_usb_dib0700 1-1:1.0: usb_probe_interface - got iddvb-usb: found a 'Hauppauge Nova-T Stick' in warm state.dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.DVB: registering new adapter (Hauppauge Nova-T Stick).DVB: registering frontend 2 (DiBcom 7000MA/MB/PA/PB/MC)...MT2060: successfully identified (IF1 = 1220)dvb-usb: Hauppauge Nova-T Stick successfully initialized and connected.drivers/usb/core/inode.c: creating file '002'ehci_hcd 0000:00:03.3: GetStatus port 2 status 001803 POWER sig=j CSC CONNECThub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/shub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501ehci_hcd 0000:00:03.3: port 2 high speedehci_hcd 0000:00:03.3: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECTusb 1-2: new high speed USB device using ehci_hcd and address 3usb 1-2: default language 0x0409usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0usb 1-2: Product: 802.11g WLAN Driveusb 1-2: Manufacturer: ASUSusb 1-2: ueventusb 1-2: usb_probe_deviceusb 1-2: configuration #1 chosen from 1 choiceusb 1-2: adding 1-2:1.0 (config #1, interface 0)usb 1-2:1.0: ueventusb 1-2:1.0: ueventndiswrapper 1-2:1.0: usb_probe_interfacendiswrapper 1-2:1.0: usb_probe_interface - got idehci_hcd 0000:00:03.3: port 2 high speedehci_hcd 0000:00:03.3: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECTusb 1-2: reset high speed USB device using ehci_hcd and address 3ndiswrapper: driver rt2500usb (Ralink,10/17/2005, 2.01.00.0000) loadedusb_endpoint usbdev1.3_ep81: ep_device_release called for usbdev1.3_ep81usb_endpoint usbdev1.3_ep01: ep_device_release called for usbdev1.3_ep01wlan0: ethernet device 00:17:31:af:3a:ab using NDIS driver: rt2500usb, version: 0x20000, NDIS version: 0x500, vendor: 'Ralink Technology Inc.', 0B05:1706.F.confwlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSKdrivers/usb/core/inode.c: creating file '003' -------------------------------------------------------------------------This SF.net email is sponsored by: Splunk Inc.Still grepping through log files to find problems? Stop.Now Search log events and configuration files using AJAX and a browser.Download your FREE copy of Splunk now >> http://get.splunk.com/_______________________________________________Linux-usb-users@xxxxxxxxxxxxxxxxxxxxxxx unsubscribe, use the last form field at:https://lists.sourceforge.net/lists/listinfo/linux-usb-users
[Linux USB] [Linux USB Devel] [Video for Linux] [Linux Audio Users] [Photo] [Yosemite News] [Yosemite Photos] [Video Projectors] [PDAs] [Free Online Dating] [Hacking TiVo] [Linux Kernel] [Linux SCSI] [XFree86] [Devices] [Big List of Linux Books] [16.7MP]
|
|