Google
  Web www.spinics.net

Re: help on frame buffer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]



Thanks for the reply.

I downloaded the latest kernel  2.6.11.11  and I followed the same step with
make modules
and
make modules_install
then I did

 mkinitrd  /boot/initrd-2.6.11.2k5.img    2.6.11.2k5

the lilo.conf file is

----------------------------------------------------------
prompt
timeout=50
default=DOS
boot=/dev/hda
map=/boot/map
install=/boot/boot.b
message=/boot/message
lba32

image=/boot/vmlinuz-2.6.11.2k5
        label=2.6.11.2k5
        initrd=/boot/initrd-2.6.11.2k5.img
        read-only
        append="root=LABEL=/"

image=/boot/vmlinuz-2.4.20-8
        label=linux
        initrd=/boot/initrd-2.4.20-8.img
        read-only
        append="root=LABEL=/"

other=/dev/hda1
        optional
        label=DOS
-----------------------------------------------------------

now I did
lilo -v

after rebooting, I am getting the following error

mount: error 19 mounting ext3
pivotroot: pivot_root (/sysroot, /initrd) failed: 2
umount   /initrd  /proc failed :2
kernel panic - not syncing : no init found, try passing "init = option"  to kernel

what would be the error in this ?

- Raja S




"Steven J. Yellin" <yellin@xxxxxxxxxxxxxxxxx>
Sent by: shrike-list-bounces@xxxxxxxxxx

06/01/2005 11:00 PM
Please respond to "Discussion of Red Hat Linux 9 (Shrike)"

       
        To:        "Discussion of Red Hat Linux 9 (Shrike)" <shrike-list@xxxxxxxxxx>
        cc:        
        Subject:        Re: help on frame buffer



    Maybe you need to do
          make modules
          make modules_install
It looks like you don't have an initrd=... line in lilo.conf for your
previous kernel, but if you do, you should make one for this kernel.

Steven Yellin

On Wed, 1 Jun 2005 Raja.Saleru@xxxxxxxxxxxxxxx wrote:

> Hi,
>
> I am using redhat linux 9,  I want to enable frame buffer support.
> I followed the following steps..
>
>
> 1.      Make sure that you have the Linux kernel source code in /usr/src/linux/.
> 2.      Log in as root and cd /usr/src/linux
> 3.      Configure the kernel:
> Run:
>         make menuconfig
>
> Select "Code maturity level options" and set "Prompt for development
> and/or incomplete code/drivers".
> Then select "Console drivers" set "Support for frame buffer devices" to
> built-in (even if it says EXPERIMENTAL). Then configure the driver. Most
> modern graphics cards can use the "VESA VGA graphics console"; use that or
> a driver that specifically matches your video card. Finally enable
> "Advanced low level driver options" and make sure that 16 and 32 bpp
> packed pixel support are enabled.
> When you are finished, chose exit and save.
> 4.      Compile the kernel
> First do:
>         make dep
>
> then:
>         make bzImage
>
> The new kernel should now be in arch/i386/boot/bzImage
> 5.      Copy the kernel to the boot directory:
>         cp arch/i386/boot/bzImage /boot/linux.vesafb
>
> 6.      Edit /etc/lilo.conf
> IMPORTANT: Keep a backup of /etc/lilo.conf, and have a rescue disk
> available. If you make a mistake at this stage, the machine may not boot.
> The file /etc/lilo.conf specifies how the system boots. The precise
> contents of the file varies from system to system, this is one example:
> boot = /dev/hda3
> delay = 30
> image = /boot/vmlinuz
>   root = /dev/hda3
>   label = Linux
>   read-only # Non-UMSDOS filesystems should be mounted read-only for
> checking
> other=/dev/hda1
>         label=nt
>         table=/dev/hda
>
> IMPORTANT: Keep a backup of /etc/lilo.conf, and have a rescue disk
> available. If you make a mistake here, the machine may not boot.
> Make a new "image" section that is a copy of the first one, but with image
> = /boot/linux.vesafb and label = Linux-vesafb. Place it just above the
> first image section.
> Add a line before the image section saying 'vga = 791'. (Meaning 1024x768,
> 16 bpp.)
> With the above example, lilo.conf would now be:
> boot = /dev/hda3
> delay = 30
> vga = 791
> image = /boot/linux.vesafb
>   root = /dev/hda3
>   label = Linux-vesafb
>   read-only # Non-UMSDOS filesystems should be mounted read-only for
> checking
> image = /boot/vmlinuz
>   root = /dev/hda3
>   label = Linux
>   read-only # Non-UMSDOS filesystems should be mounted read-only for
> checking
> other=/dev/hda1
>         label=nt
>         table=/dev/hda
>
> Do not change any lines in the file; just add new ones.
> 7.      Run lilo
> To make the new changes take effect, run the lilo program:
>         lilo
>
> 8.      Reboot the system
>
> --------------------------------------------------------------
>
> after rebooting, the kernel is not booting...
> it says kernel version mismatch and kernel panic, mention the correct
> root.

>
> can anybody help in this ?
>
>
> Raja Saleru
> LARSEN & TOUBRO INFOTECH LIMITED
> Communications & Embedded Systems
> No.4, Service Road,
> Domlur Layout,
> Bangalore - 560 071
> INDIA
> Tel : +91-80-25350510/512 Extn : 106
> Mobile : +91-
> Fax : +91-80-25350495
>
>
> ______________________________________________________________________

--
Shrike-list mailing list
Shrike-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/shrike-list

______________________________________________________________________



______________________________________________________________________
-- 
Shrike-list mailing list
Shrike-list@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/shrike-list

[Fedora Users]     [Centos Users]     [Kernel Development]     [Red Hat Install]     [Red Hat Watch]     [Red Hat Development]     [Red Hat Phoebe Beta]     [Yosemite Forum]     [Fedora Discussion]     [Gimp]     [Stuff]     [Yosemite News]

Powered by Linux