RE: [PATCH v4 3/9] phy: Add new Exynos USB PHY driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

> From: Kamil Debski [mailto:k.debski@xxxxxxxxxxx]
> Sent: Friday, December 06, 2013 5:28 PM
> 
> Hi Kishon,
> 
> Thank you for the review.
> 
> > From: Kishon Vijay Abraham I [mailto:kishon@xxxxxx]
> > Sent: Friday, December 06, 2013 11:59 AM
> >
> > Hi,
> >
> > On Thursday 05 December 2013 05:59 PM, Kamil Debski wrote:
> > > Add a new driver for the Exynos USB PHY. The new driver uses the
> > > generic PHY framework. The driver includes support for the Exynos
> > 4x10
> > > and 4x12 SoC families.
> > >
> > > Signed-off-by: Kamil Debski <k.debski@xxxxxxxxxxx>
> > > Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
> > > ---
> > >  .../devicetree/bindings/phy/samsung-usbphy.txt     |   54 ++++
> > >  drivers/phy/Kconfig                                |   20 ++
> > >  drivers/phy/Makefile                               |    3 +
> > >  drivers/phy/phy-exynos4210-usb2.c                  |  264
> > +++++++++++++++++
> > >  drivers/phy/phy-exynos4212-usb2.c                  |  312
> > ++++++++++++++++++++
> > >  drivers/phy/phy-samsung-usb2.c                     |  228
> > ++++++++++++++
> > >  drivers/phy/phy-samsung-usb2.h                     |   72 +++++
> > >  7 files changed, 953 insertions(+)
> > >  create mode 100644
> > > Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> > >  create mode 100644 drivers/phy/phy-exynos4210-usb2.c  create mode
> > > 100644 drivers/phy/phy-exynos4212-usb2.c  create mode 100644
> > > drivers/phy/phy-samsung-usb2.c  create mode 100644
> > > drivers/phy/phy-samsung-usb2.h
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> > > b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> > > new file mode 100644
> > > index 0000000..cadbf70
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt
> >
> > use the existing samsung-phy.txt.
> 
> Ok.
> 
> > > @@ -0,0 +1,54 @@
> > > +Samsung S5P/EXYNOS SoC series USB PHY
> > > +-------------------------------------------------
> > > +
> > > +Required properties:
> > > +- compatible : should be one of the listed compatibles:
> > > +	- "samsung,exynos4210-usb2-phy"
> > > +	- "samsung,exynos4212-usb2-phy"
> > > +- reg : a list of registers used by phy driver
> > > +	- first and obligatory is the location of phy modules registers
> > > +- samsung,sysreg-phandle - handle to syscon used to control the
> > > +system registers
> > > +- samsung,pmureg-phandle - handle to syscon used to control PMU
> > > +registers
> > > +- #phy-cells : from the generic phy bindings, must be 1;
> > > +- clocks and clock-names:
> > > +	- the "phy" clocks is required by the phy module
> > > +	- next for each of the phys a clock has to be assidned, this
> > clock
> >
> > %s/assidned/assigned/
> 
> Thank you for spotting this.
> 
> > > +	  will be used to determine clocking frequency for the phys
> > > +	  (the labels are specified in the paragraph below)
> > > +
> > > +The first phandle argument in the PHY specifier identifies the PHY,
> > > +its meaning is compatible dependent. For the currently supported
> > SoCs
> > > +(Exynos 4210 and Exynos 4212) it is as follows:
> > > +  0 - USB device ("device"),
> > > +  1 - USB host ("host"),
> > > +  2 - HSIC0 ("hsic0"),
> > > +  3 - HSIC1 ("hsic1"),
> > > +
> > > +Exynos 4210 and Exynos 4212 use mode switching and require that
> > > +mode switch register is supplied.
> > > +
> > > +Example:
> > > +
> > > +For Exynos 4412 (compatible with Exynos 4212):
> > > +
> > > +usbphy: phy@125B0000 {
> >
> > use lower case for address here...
> 
> Ok.
> 
> > > +	compatible = "samsung,exynos4212-usb2-phy";
> > > +	reg = <0x125B0000 0x100 0x10020704 0x0c 0x1001021c 0x4>;
> > and here..
> > > +	clocks = <&clock 305>, <&clock 2>, <&clock 2>, <&clock 2>,
> > > +							<&clock 2>;
> > > +	clock-names = "phy", "device", "host", "hsic0", "hsic1";
> > > +	status = "okay";
> > > +	#phy-cells = <1>;
> > > +	samsung,sysreg-phandle = <&sys_reg>;
> > > +	samsung,pmureg-phandle = <&pmu_reg>; };
> > > +
> > > +Then the PHY can be used in other nodes such as:
> > > +
> > > +phy-consumer@12340000 {
> > > +	phys = <&usbphy 2>;
> > > +	phy-names = "phy";
> > > +};
> > > +
> > > +Refer to DT bindings documentation of particular PHY consumer
> > devices
> > > +for more information about required PHYs and the way of
> > specification.
> > > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index
> > > a344f3d..b29018f 100644
> > > --- a/drivers/phy/Kconfig
> > > +++ b/drivers/phy/Kconfig
> > > @@ -51,4 +51,24 @@ config PHY_EXYNOS_DP_VIDEO
> > >  	help
> > >  	  Support for Display Port PHY found on Samsung EXYNOS SoCs.
> > >
> > > +config PHY_SAMSUNG_USB2
> > > +	tristate "Samsung USB 2.0 PHY driver"
> > > +	help
> > > +	  Enable this to support Samsung USB phy helper driver for
> > Samsung SoCs.
> > > +	  This driver provides common interface to interact, for Samsung
> > > +	  USB 2.0 PHY driver.
> > > +
> > > +config PHY_EXYNOS4210_USB2
> > > +	bool "Support for Exynos 4210"
> > > +	depends on PHY_SAMSUNG_USB2
> > > +	depends on CPU_EXYNOS4210
> >
> > select GENERIC_PHY here?
> 
> I think that depends on PHY_SAMSUNG_USB2 is better in this place.
> However, I agree that I should add select GENERIC_PHY to
> PHY_SAMSUNG_USB2.
> 
> The reason why I am saying this is that I like how it looks in
> menuconfig. Selecting PHY_SAMSUNG_USB2 expands more options and if
> unselected the menu looks tidier.
> 
> > > +	help
> > > +	  Enable USB PHY support for Exynos 4210
> >
> > Add more explanation here and make checkpatch happy.
> 
> Here I think we should not treat checkpatch as an oracle. I also
> noticed these warnings, but I think that writing a four line
> description for SoC specific options in this menu is an overkill. In
> addition, checkpatch also complains for the following entries in
> Kconfig file:
> - PHY_EXYNOS_MIPI_VIDEO
> - PHY_EXYNOS_DP_VIDEO
> - PHY_SAMSUNG_USB2 (here expanding the description may be justified,
> but
>   I think the current description is enough)
> 
> But thank you for directing my attention to the Kconfig file. I noticed
> That SoC specific Kconfig entries should have "USB 2.0" instead of just
> "USB".
> 
> > > +
> > > +config PHY_EXYNOS4212_USB2
> > > +	bool "Support for Exynos 4212"
> > > +	depends on PHY_SAMSUNG_USB2
> > > +	depends on (SOC_EXYNOS4212 || SOC_EXYNOS4412)
> >
> > select GENERIC_PHY.
> 
> Please check my reply above.
> 
> > > +	help
> > > +	  Enable USB PHY support for Exynos 4212
> >
> > more explanation here too..
> 
> Please check my reply above.
> 
> > >  endmenu
> > > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index
> > > d0caae9..9f4befd 100644
> > > --- a/drivers/phy/Makefile
> > > +++ b/drivers/phy/Makefile
> > > @@ -7,3 +7,6 @@ obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-
> exynos-dp-
> > video.o
> > >  obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
> > >  obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
> > >  obj-$(CONFIG_TWL4030_USB)		+= phy-twl4030-usb.o
> > > +obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-samsung-usb2.o
> > > +obj-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
> > > +obj-$(CONFIG_PHY_EXYNOS4212_USB2)	+= phy-exynos4212-usb2.o
> > > diff --git a/drivers/phy/phy-exynos4210-usb2.c
> > > b/drivers/phy/phy-exynos4210-usb2.c
> > > new file mode 100644
> > > index 0000000..a02e5c2
> > > --- /dev/null
> > > +++ b/drivers/phy/phy-exynos4210-usb2.c
> > > @@ -0,0 +1,264 @@
> > > +/*
> > > + * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4210 support
> > > + *
> > > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > > + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > +modify
> > > + * it under the terms of the GNU General Public License version 2
> > > +as
> > > + * published by the Free Software Foundation.
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/of_address.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/spinlock.h>
> >
> > You've included most of the above header files in phy-samsung-usb2.h
> > which you are including below.
> 
> I agree that includes in phy-samsung-usb2.h could use a cleanup. On the
> other hand my opinion is that a .c file should include all .h files
> that are used in this .c file. Relaying on .h file to include
> another .h doesn't seem good to me.
> 
> > > +#include "phy-samsung-usb2.h"
> > > +
> > > +/* Exynos USB PHY registers */
> > > +
> > > +/* PHY power control */
> > > +#define EXYNOS_4210_UPHYPWR			0x0
> > > +
> > > +#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND	(1 << 0)
> >
> > use BIT() here and everywhere below.
> 
> All right.
> 
> > > +#define EXYNOS_4210_UPHYPWR_PHY0_PWR		(1 << 3)
> >
> > replace PHY0 here with DEV so it looks similar to EXYNOS_4212.
> > > +#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR	(1 << 4)
> > > +#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP		(1 << 5)
> > > +#define EXYNOS_4210_UPHYPWR_PHY0	( \
> > > +	EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \
> > > +	EXYNOS_4210_UPHYPWR_PHY0_PWR | \
> > > +	EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \
> > > +	EXYNOS_4210_UPHYPWR_PHY0_SLEEP)
> > > +
> > > +#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND	(1 << 6)
> >
> > replace PHY0 here with HOST so it looks similar to EXYNOS_4212.
> 
> Thank you for spotting this inconsistence. I will fix that. But I
> rather incline to use PHY0/1 instead of DEVICE/HOST as it will be then
> consistent with the date sheet.
> 
> > > +#define EXYNOS_4210_UPHYPWR_PHY1_PWR		(1 << 7)
> > > +#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP		(1 << 8)
> > > +#define EXYNOS_4210_UPHYPWR_PHY1 ( \
> > > +	EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \
> > > +	EXYNOS_4210_UPHYPWR_PHY1_PWR | \
> > > +	EXYNOS_4210_UPHYPWR_PHY1_SLEEP)
> > > +
> > > +#define EXYNOS_4210_UPHYPWR_HSCI0_SUSPEND	(1 << 9)
> > > +#define EXYNOS_4210_UPHYPWR_HSCI0_SLEEP		(1 << 10)
> > > +#define EXYNOS_4210_UPHYPWR_HSCI0 ( \
> > > +	EXYNOS_4210_UPHYPWR_HSCI0_SUSPEND | \
> > > +	EXYNOS_4210_UPHYPWR_HSCI0_SLEEP)
> > > +
> > > +#define EXYNOS_4210_UPHYPWR_HSCI1_SUSPEND	(1 << 11)
> > > +#define EXYNOS_4210_UPHYPWR_HSCI1_SLEEP		(1 << 12)
> > > +#define EXYNOS_4210_UPHYPWR_HSCI1 ( \
> > > +	EXYNOS_4210_UPHYPWR_HSCI1_SUSPEND | \
> > > +	EXYNOS_4210_UPHYPWR_HSCI1_SLEEP)
> > > +
> > > +/* PHY clock control */
> > > +#define EXYNOS_4210_UPHYCLK			0x4
> > > +
> > > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK	(0x3 << 0)
> > > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ	(0x0 << 0)
> > > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ	(0x3 << 0)
> > > +#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ	(0x2 << 0)
> > > +
> > > +#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP	(0x1 << 2)
> > > +#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON	(0x1 << 4)
> > > +#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON	(0x1 << 7)
> > > +
> > > +/* PHY reset control */
> > > +#define EXYNOS_4210_UPHYRST			0x8
> > > +
> > > +#define EXYNOS_4210_URSTCON_PHY0		(1 << 0)
> > > +#define EXYNOS_4210_URSTCON_OTG_HLINK		(1 << 1)
> > > +#define EXYNOS_4210_URSTCON_OTG_PHYLINK		(1 << 2)
> > > +#define EXYNOS_4210_URSTCON_PHY1_ALL		(1 << 3)
> > > +#define EXYNOS_4210_URSTCON_PHY1_P0		(1 << 4)
> > > +#define EXYNOS_4210_URSTCON_PHY1_P1P2		(1 << 5)
> > > +#define EXYNOS_4210_URSTCON_HOST_LINK_ALL	(1 << 6)
> > > +#define EXYNOS_4210_URSTCON_HOST_LINK_P0	(1 << 7)
> > > +#define EXYNOS_4210_URSTCON_HOST_LINK_P1	(1 << 8)
> > > +#define EXYNOS_4210_URSTCON_HOST_LINK_P2	(1 << 9)
> > > +
> > > +/* Isolation, configured in the power management unit */
> > > +#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET	0x704
> > > +#define EXYNOS_4210_USB_ISOL_DEVICE		(1 << 0)
> > > +#define EXYNOS_4210_USB_ISOL_HOST_OFFSET	0x708
> > > +#define EXYNOS_4210_USB_ISOL_HOST		(1 << 0)
> > > +
> > > +/* USBYPHY1 Floating prevention */
> > > +#define EXYNOS_4210_UPHY1CON			0x34
> > > +#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION	0x1
> > > +
> > > +/* Mode switching SUB Device <-> Host */
> > > +#define EXYNOS_4210_MODE_SWITCH_OFFSET		0x21c
> > > +#define EXYNOS_4210_MODE_SWITCH_MASK		1
> > > +#define EXYNOS_4210_MODE_SWITCH_DEVICE		0
> > > +#define EXYNOS_4210_MODE_SWITCH_HOST		1
> > > +
> > > +enum exynos4210_phy_id {
> > > +	EXYNOS4210_DEVICE,
> > > +	EXYNOS4210_HOST,
> > > +	EXYNOS4210_HSIC0,
> > > +	EXYNOS4210_HSIC1,
> > > +	EXYNOS4210_NUM_PHYS,
> > > +};
> > > +
> > > +/*
> > > + * exynos4210_rate_to_clk() converts the supplied clock rate to
> the
> > > +value that
> > > + * can be written to the phy register.
> > > + */
> > > +static int exynos4210_rate_to_clk(unsigned long rate, u32 *reg) {
> > > +	switch (rate) {
> > > +	case 12 * MHZ:
> > > +		*reg = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ;
> > > +		break;
> > > +	case 24 * MHZ:
> > > +		*reg = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ;
> > > +		break;
> > > +	case 48 * MHZ:
> > > +		reg = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ;
> >
> > %s/reg/*Reg
> 
> Thank you.
> 
> > > +		break;
> > > +	default:
> > > +		return -EINVAL;
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static void exynos4210_isol(struct samsung_usb2_phy_instance *inst,
> > > +bool on) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	u32 offset;
> > > +	u32 mask;
> > > +
> > > +	switch (inst->cfg->id) {
> > > +	case EXYNOS4210_DEVICE:
> > > +		offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET;
> > > +		mask = EXYNOS_4210_USB_ISOL_DEVICE;
> > > +		break;
> > > +	case EXYNOS4210_HOST:
> > > +		offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET;
> > > +		mask = EXYNOS_4210_USB_ISOL_HOST;
> > > +		break;
> > > +	default:
> > > +		return;
> > > +	};
> > > +
> > > +	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); }
> > > +
> > > +static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance
> > > +*inst, bool on) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	u32 rstbits = 0;
> > > +	u32 phypwr = 0;
> > > +	u32 rst;
> > > +	u32 pwr;
> > > +
> > > +	switch (inst->cfg->id) {
> > > +	case EXYNOS4210_DEVICE:
> > > +		phypwr =	EXYNOS_4210_UPHYPWR_PHY0;
> > > +		rstbits =	EXYNOS_4210_URSTCON_PHY0;
> > > +		break;
> > > +	case EXYNOS4210_HOST:
> > > +		phypwr =	EXYNOS_4210_UPHYPWR_PHY1;
> > > +		rstbits =	EXYNOS_4210_URSTCON_PHY1_ALL |
> > > +				EXYNOS_4210_URSTCON_PHY1_P0 |
> > > +				EXYNOS_4210_URSTCON_PHY1_P1P2 |
> > > +				EXYNOS_4210_URSTCON_HOST_LINK_ALL |
> > > +				EXYNOS_4210_URSTCON_HOST_LINK_P0;
> > > +		writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON);
> > > +		break;
> > > +	case EXYNOS4210_HSIC0:
> > > +		phypwr =	EXYNOS_4210_UPHYPWR_HSCI0;
> > > +		rstbits =	EXYNOS_4210_URSTCON_PHY1_P1P2 |
> > > +				EXYNOS_4210_URSTCON_HOST_LINK_P1;
> > > +		break;
> > > +	case EXYNOS4210_HSIC1:
> > > +		phypwr =	EXYNOS_4210_UPHYPWR_HSCI1;
> > > +		rstbits =	EXYNOS_4210_URSTCON_PHY1_P1P2 |
> > > +				EXYNOS_4210_URSTCON_HOST_LINK_P2;
> > > +		break;
> > > +	};
> > > +
> > > +	if (on) {
> > > +		writel(inst->clk_reg_val, drv->reg_phy +
> > EXYNOS_4210_UPHYCLK);
> > > +
> > > +		pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
> > > +		pwr &= ~phypwr;
> > > +		writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
> > > +
> > > +		rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST);
> > > +		rst |= rstbits;
> > > +		writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
> > > +		udelay(10);
> > > +		rst &= ~rstbits;
> > > +		writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
> >
> > Do you have to reset during every power on? IMO this reset should be
> > done once in phy_init.
> 
> It seems that this reset is neded by the hardware.
> 
> > > +	} else {
> > > +		pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
> > > +		pwr |= phypwr;
> > > +		writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
> > > +	}
> > > +}
> > > +
> > > +static int exynos4210_power_on(struct samsung_usb2_phy_instance
> > > +*inst) {
> > > +	/* Order of initialisation is important - first power then
> > isolation */
> > > +	exynos4210_phy_pwr(inst, 1);
> > > +	exynos4210_isol(inst, 0);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static int exynos4210_power_off(struct samsung_usb2_phy_instance
> > > +*inst) {
> > > +	exynos4210_isol(inst, 1);
> > > +	exynos4210_phy_pwr(inst, 0);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +
> > > +static const struct samsung_usb2_common_phy exynos4210_phys[] = {
> > > +	{
> > > +		.label		= "device",
> > > +		.id		= EXYNOS4210_DEVICE,
> > > +		.rate_to_clk	= exynos4210_rate_to_clk,
> > > +		.power_on	= exynos4210_power_on,
> > > +		.power_off	= exynos4210_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "host",
> > > +		.id		= EXYNOS4210_HOST,
> > > +		.rate_to_clk	= exynos4210_rate_to_clk,
> > > +		.power_on	= exynos4210_power_on,
> > > +		.power_off	= exynos4210_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "hsic0",
> > > +		.id		= EXYNOS4210_HSIC0,
> > > +		.rate_to_clk	= exynos4210_rate_to_clk,
> > > +		.power_on	= exynos4210_power_on,
> > > +		.power_off	= exynos4210_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "hsic1",
> > > +		.id		= EXYNOS4210_HSIC1,
> > > +		.rate_to_clk	= exynos4210_rate_to_clk,
> > > +		.power_on	= exynos4210_power_on,
> > > +		.power_off	= exynos4210_power_off,
> > > +	},
> > > +	{},
> > > +};
> > > +
> > > +const struct samsung_usb2_phy_config exynos4210_usb2_phy_config =
> {
> > > +	.num_phys		= EXYNOS4210_NUM_PHYS,
> > > +	.phys			= exynos4210_phys,
> > > +	.has_mode_switch	= 1,
> > > +};
> > > +
> > > diff --git a/drivers/phy/phy-exynos4212-usb2.c
> > > b/drivers/phy/phy-exynos4212-usb2.c
> > > new file mode 100644
> > > index 0000000..375ece0
> > > --- /dev/null
> > > +++ b/drivers/phy/phy-exynos4212-usb2.c
> > > @@ -0,0 +1,312 @@
> > > +/*
> > > + * Samsung S5P/EXYNOS SoC series USB PHY driver - Exynos 4212
> > support
> > > + *
> > > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > > + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > +modify
> > > + * it under the terms of the GNU General Public License version 2
> > > +as
> > > + * published by the Free Software Foundation.
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/of_address.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/spinlock.h>
> >
> > You've included most of the above header files in phy-samsung-usb2.h
> > which you are including below.
> 
> Please see my reply above.
> 
> > > +#include "phy-samsung-usb2.h"
> > > +
> > > +/* Exynos USB PHY registers */
> > > +
> > > +/* PHY power control */
> > > +#define EXYNOS_4212_UPHYPWR			0x0
> > > +
> > > +#define EXYNOS_4212_UPHYPWR_DEV_SUSPEND		(1 << 0)
> >
> > use BIT() here and below..
> 
> All right.
> 
> > > +#define EXYNOS_4212_UPHYPWR_DEV_PWR		(1 << 3)
> > > +#define EXYNOS_4212_UPHYPWR_DEV_OTG_PWR		(1 << 4)
> > > +#define EXYNOS_4212_UPHYPWR_DEV_SLEEP		(1 << 5)
> > > +#define EXYNOS_4212_UPHYPWR_DEV	( \
> > > +	EXYNOS_4212_UPHYPWR_DEV_SUSPEND | \
> > > +	EXYNOS_4212_UPHYPWR_DEV_PWR | \
> > > +	EXYNOS_4212_UPHYPWR_DEV_OTG_PWR | \
> > > +	EXYNOS_4212_UPHYPWR_DEV_SLEEP)
> > > +
> > > +#define EXYNOS_4212_UPHYPWR_HOST_SUSPEND	(1 << 6)
> > > +#define EXYNOS_4212_UPHYPWR_HOST_PWR		(1 << 7)
> > > +#define EXYNOS_4212_UPHYPWR_HOST_SLEEP		(1 << 8)
> > > +#define EXYNOS_4212_UPHYPWR_HOST ( \
> > > +	EXYNOS_4212_UPHYPWR_HOST_SUSPEND | \
> > > +	EXYNOS_4212_UPHYPWR_HOST_PWR | \
> > > +	EXYNOS_4212_UPHYPWR_HOST_SLEEP)
> > > +
> > > +#define EXYNOS_4212_UPHYPWR_HSCI0_SUSPEND	(1 << 9)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI0_PWR		(1 << 10)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI0_SLEEP		(1 << 11)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI0 ( \
> > > +	EXYNOS_4212_UPHYPWR_HSCI0_SUSPEND | \
> > > +	EXYNOS_4212_UPHYPWR_HSCI0_PWR | \
> > > +	EXYNOS_4212_UPHYPWR_HSCI0_SLEEP)
> > > +
> > > +#define EXYNOS_4212_UPHYPWR_HSCI1_SUSPEND	(1 << 12)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI1_PWR		(1 << 13)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI1_SLEEP		(1 << 14)
> > > +#define EXYNOS_4212_UPHYPWR_HSCI1 ( \
> > > +	EXYNOS_4212_UPHYPWR_HSCI1_SUSPEND | \
> > > +	EXYNOS_4212_UPHYPWR_HSCI1_PWR | \
> > > +	EXYNOS_4212_UPHYPWR_HSCI1_SLEEP)
> > > +
> > > +/* PHY clock control */
> > > +#define EXYNOS_4212_UPHYCLK			0x4
> > > +
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_MASK	(0x7 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_9MHZ6	(0x0 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_10MHZ	(0x1 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_12MHZ	(0x2 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_19MHZ2	(0x3 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_20MHZ	(0x4 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_24MHZ	(0x5 << 0)
> > > +#define EXYNOS_4212_UPHYCLK_PHYFSEL_50MHZ	(0x7 << 0)
> > > +
> > > +#define EXYNOS_4212_UPHYCLK_PHY0_ID_PULLUP	(0x1 << 3)
> > > +#define EXYNOS_4212_UPHYCLK_PHY0_COMMON_ON	(0x1 << 4)
> > > +#define EXYNOS_4212_UPHYCLK_PHY1_COMMON_ON	(0x1 << 7)
> > > +
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_MASK	(0x7f << 10)
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_12MHZ	(0x24 << 10)
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_15MHZ	(0x1c << 10)
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_16MHZ	(0x1a << 10)
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_19MHZ2	(0x15 << 10)
> > > +#define EXYNOS_4212_UPHYCLK_HSIC_REFCLK_20MHZ	(0x14 << 10)
> > > +
> > > +/* PHY reset control */
> > > +#define EXYNOS_4212_UPHYRST			0x8
> > > +
> > > +#define EXYNOS_4212_URSTCON_DEVICE		(1 << 0)
> > > +#define EXYNOS_4212_URSTCON_OTG_HLINK		(1 << 1)
> > > +#define EXYNOS_4212_URSTCON_OTG_PHYLINK		(1 << 2)
> > > +#define EXYNOS_4212_URSTCON_HOST_PHY		(1 << 3)
> > > +#define EXYNOS_4212_URSTCON_PHY1		(1 << 4)
> > > +#define EXYNOS_4212_URSTCON_HSIC0		(1 << 5)
> > > +#define EXYNOS_4212_URSTCON_HSIC1		(1 << 6)
> > > +#define EXYNOS_4212_URSTCON_HOST_LINK_ALL	(1 << 7)
> > > +#define EXYNOS_4212_URSTCON_HOST_LINK_P0	(1 << 8)
> > > +#define EXYNOS_4212_URSTCON_HOST_LINK_P1	(1 << 9)
> > > +#define EXYNOS_4212_URSTCON_HOST_LINK_P2	(1 << 10)
> > > +
> > > +/* Isolation, configured in the power management unit */
> > > +#define EXYNOS_4212_USB_ISOL_OFFSET		0x704
> > > +#define EXYNOS_4212_USB_ISOL_OTG		(1 << 0)
> > > +#define EXYNOS_4212_USB_ISOL_HSIC0_OFFSET	0x708
> > > +#define EXYNOS_4212_USB_ISOL_HSIC0		(1 << 0)
> > > +#define EXYNOS_4212_USB_ISOL_HSIC1_OFFSET	0x70c
> > > +#define EXYNOS_4212_USB_ISOL_HSIC1		(1 << 0)
> > > +
> > > +/* Mode switching SUB Device <-> Host */
> > > +#define EXYNOS_4212_MODE_SWITCH_OFFSET		0x21c
> > > +#define EXYNOS_4212_MODE_SWITCH_MASK		1
> > > +#define EXYNOS_4212_MODE_SWITCH_DEVICE		0
> > > +#define EXYNOS_4212_MODE_SWITCH_HOST		1
> > > +
> > > +enum exynos4x12_phy_id {
> > > +	EXYNOS4212_DEVICE,
> > > +	EXYNOS4212_HOST,
> > > +	EXYNOS4212_HSIC0,
> > > +	EXYNOS4212_HSIC1,
> > > +	EXYNOS4212_NUM_PHYS,
> > > +};
> > > +
> > > +/*
> > > + * exynos4212_rate_to_clk() converts the supplied clock rate to
> the
> > > +value that
> > > + * can be written to the phy register.
> > > + */
> > > +static int exynos4212_rate_to_clk(unsigned long rate, u32 *reg) {
> > > +	/* EXYNOS_4212_UPHYCLK_PHYFSEL_MASK */
> > > +
> > > +	switch (rate) {
> > > +	case 9600 * KHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_9MHZ6;
> > > +		break;
> > > +	case 10 * MHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_10MHZ;
> > > +		break;
> > > +	case 12 * MHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_12MHZ;
> > > +		break;
> > > +	case 19200 * KHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_19MHZ2;
> > > +		break;
> > > +	case 20 * MHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_20MHZ;
> > > +		break;
> > > +	case 24 * MHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_24MHZ;
> > > +		break;
> > > +	case 50 * MHZ:
> > > +		*reg = EXYNOS_4212_UPHYCLK_PHYFSEL_50MHZ;
> > > +		break;
> > > +	default:
> > > +		return -EINVAL;
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static void exynos4212_isol(struct samsung_usb2_phy_instance *inst,
> > > +bool on) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	u32 offset;
> > > +	u32 mask;
> > > +
> > > +	switch (inst->cfg->id) {
> > > +	case EXYNOS4212_DEVICE:
> > > +	case EXYNOS4212_HOST:
> > > +		offset = EXYNOS_4212_USB_ISOL_OFFSET;
> > > +		mask = EXYNOS_4212_USB_ISOL_OTG;
> > > +		break;
> > > +	case EXYNOS4212_HSIC0:
> > > +		offset = EXYNOS_4212_USB_ISOL_HSIC0_OFFSET;
> > > +		mask = EXYNOS_4212_USB_ISOL_HSIC0;
> > > +		break;
> > > +	case EXYNOS4212_HSIC1:
> > > +		offset = EXYNOS_4212_USB_ISOL_HSIC1_OFFSET;
> > > +		mask = EXYNOS_4212_USB_ISOL_HSIC1;
> > > +		break;
> > > +	default:
> > > +		return;
> > > +	};
> > > +
> > > +	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask); }
> > > +
> > > +static void exynos4212_phy_pwr(struct samsung_usb2_phy_instance
> > > +*inst, bool on) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	u32 rstbits = 0;
> > > +	u32 phypwr = 0;
> > > +	u32 rst;
> > > +	u32 pwr;
> > > +
> > > +	switch (inst->cfg->id) {
> > > +	case EXYNOS4212_DEVICE:
> > > +		phypwr =	EXYNOS_4212_UPHYPWR_DEV;
> > > +		rstbits =	EXYNOS_4212_URSTCON_DEVICE;
> > > +		break;
> > > +	case EXYNOS4212_HOST:
> > > +		phypwr =	EXYNOS_4212_UPHYPWR_HOST;
> > > +		rstbits =	EXYNOS_4212_URSTCON_HOST_PHY;
> > > +		break;
> > > +	case EXYNOS4212_HSIC0:
> > > +		phypwr =	EXYNOS_4212_UPHYPWR_HSCI0;
> > > +		rstbits =	EXYNOS_4212_URSTCON_HSIC1 |
> > > +				EXYNOS_4212_URSTCON_HOST_LINK_P0 |
> > > +				EXYNOS_4212_URSTCON_HOST_PHY;
> > > +		break;
> > > +	case EXYNOS4212_HSIC1:
> > > +		phypwr =	EXYNOS_4212_UPHYPWR_HSCI1;
> > > +		rstbits =	EXYNOS_4212_URSTCON_HSIC1 |
> > > +				EXYNOS_4212_URSTCON_HOST_LINK_P1;
> > > +		break;
> > > +	};
> > > +
> > > +	if (on) {
> > > +		writel(inst->clk_reg_val, drv->reg_phy +
> > EXYNOS_4212_UPHYCLK);
> > > +
> > > +		pwr = readl(drv->reg_phy + EXYNOS_4212_UPHYPWR);
> > > +		pwr &= ~phypwr;
> > > +		writel(pwr, drv->reg_phy + EXYNOS_4212_UPHYPWR);
> > > +
> > > +		rst = readl(drv->reg_phy + EXYNOS_4212_UPHYRST);
> > > +		rst |= rstbits;
> > > +		writel(rst, drv->reg_phy + EXYNOS_4212_UPHYRST);
> > > +		udelay(10);
> > > +		rst &= ~rstbits;
> > > +		writel(rst, drv->reg_phy + EXYNOS_4212_UPHYRST);
> >
> > reset should be done once in init?
> 
> The hardware seems to need this reset.
> 
> > > +	} else {
> > > +		pwr = readl(drv->reg_phy + EXYNOS_4212_UPHYPWR);
> > > +		pwr |= phypwr;
> > > +		writel(pwr, drv->reg_phy + EXYNOS_4212_UPHYPWR);
> > > +	}
> > > +}
> > > +
> > > +static int exynos4212_power_on(struct samsung_usb2_phy_instance
> > > +*inst) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +
> > > +	inst->enabled = 1;
> > > +	exynos4212_phy_pwr(inst, 1);
> > > +	exynos4212_isol(inst, 0);
> > > +
> > > +	/* Power on the device, as it is necessary for HSIC to work */
> >
> > This looks weird. How powering on the 'device PHY' makes 'HSIC PHY'
> to
> > work?
> 
> I agree with you that it looks weird, but I found this necessary to be
> done.
> 
> > > +	if (inst->cfg->id == EXYNOS4212_HSIC0) {
> > > +		struct samsung_usb2_phy_instance *device =
> > > +					&drv->instances[EXYNOS4212_DEVICE];
> > > +		exynos4212_phy_pwr(device, 1);
> > > +		exynos4212_isol(device, 0);
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static int exynos4212_power_off(struct samsung_usb2_phy_instance
> > > +*inst) {
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	struct samsung_usb2_phy_instance *device =
> > > +&drv->instances[EXYNOS4212_DEVICE];
> > > +
> > > +	inst->enabled = 0;
> > > +	exynos4212_isol(inst, 1);
> > > +	exynos4212_phy_pwr(inst, 0);
> > > +
> > > +	if (inst->cfg->id == EXYNOS4212_HSIC0 && !device->enabled) {
> > > +		exynos4212_isol(device, 1);
> > > +		exynos4212_phy_pwr(device, 0);
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +
> > > +static const struct samsung_usb2_common_phy exynos4212_phys[] = {
> > > +	{
> > > +		.label		= "device",
> > > +		.id		= EXYNOS4212_DEVICE,
> > > +		.rate_to_clk	= exynos4212_rate_to_clk,
> > > +		.power_on	= exynos4212_power_on,
> > > +		.power_off	= exynos4212_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "host",
> > > +		.id		= EXYNOS4212_HOST,
> > > +		.rate_to_clk	= exynos4212_rate_to_clk,
> > > +		.power_on	= exynos4212_power_on,
> > > +		.power_off	= exynos4212_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "hsic0",
> > > +		.id		= EXYNOS4212_HSIC0,
> > > +		.rate_to_clk	= exynos4212_rate_to_clk,
> > > +		.power_on	= exynos4212_power_on,
> > > +		.power_off	= exynos4212_power_off,
> > > +	},
> > > +	{
> > > +		.label		= "hsic1",
> > > +		.id		= EXYNOS4212_HSIC1,
> > > +		.rate_to_clk	= exynos4212_rate_to_clk,
> > > +		.power_on	= exynos4212_power_on,
> > > +		.power_off	= exynos4212_power_off,
> > > +	},
> > > +	{},
> > > +};
> > > +
> > > +const struct samsung_usb2_phy_config exynos4212_usb2_phy_config =
> {
> > > +	.num_phys		= EXYNOS4212_NUM_PHYS,
> > > +	.phys			= exynos4212_phys,
> > > +	.has_mode_switch	= 1,
> > > +};
> > > +
> > > diff --git a/drivers/phy/phy-samsung-usb2.c
> > > b/drivers/phy/phy-samsung-usb2.c new file mode 100644 index
> > > 0000000..804ec77
> > > --- /dev/null
> > > +++ b/drivers/phy/phy-samsung-usb2.c
> > > @@ -0,0 +1,228 @@
> > > +/*
> > > + * Samsung SoC USB 1.1/2.0 PHY driver
> > > + *
> > > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > > + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > +modify
> > > + * it under the terms of the GNU General Public License version 2
> > > +as
> > > + * published by the Free Software Foundation.
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/mfd/syscon.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/of_address.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/spinlock.h>
> >
> > You've included most of the above header files in phy-samsung-usb2.h
> > which you are including below.
> 
> Please see my answer above.
> 
> > > +#include "phy-samsung-usb2.h"
> > > +
> > > +static int samsung_usb2_phy_power_on(struct phy *phy) {
> > > +	struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	int ret;
> > > +
> > > +	dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n",
> > > +							inst->cfg->label);
> > > +	ret = clk_prepare_enable(drv->clk);
> > > +	if (ret)
> > > +		goto err_main_clk;
> > > +	ret = clk_prepare_enable(inst->clk);
> > > +	if (ret)
> > > +		goto err_instance_clk;
> > > +	inst->rate = clk_get_rate(inst->clk);
> > > +	if (inst->cfg->rate_to_clk) {
> > > +		ret = inst->cfg->rate_to_clk(inst->rate, &inst-
> > >clk_reg_val);
> > > +		if (ret)
> > > +			goto err_get_rate;
> > > +	}
> > > +	if (inst->cfg->power_on) {
> > > +		spin_lock(&drv->lock);
> > > +		ret = inst->cfg->power_on(inst);
> > > +		spin_unlock(&drv->lock);
> > > +	}
> > > +
> > > +	return 0;
> > > +
> > > +err_get_rate:
> > > +	clk_disable_unprepare(inst->clk);
> > > +err_instance_clk:
> > > +	clk_disable_unprepare(drv->clk);
> > > +err_main_clk:
> > > +	return ret;
> > > +}
> > > +
> > > +static int samsung_usb2_phy_power_off(struct phy *phy) {
> > > +	struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
> > > +	struct samsung_usb2_phy_driver *drv = inst->drv;
> > > +	int ret = 0;
> > > +
> > > +	dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n",
> > > +							inst->cfg->label);
> > > +	if (inst->cfg->power_off) {
> > > +		spin_lock(&drv->lock);
> > > +		ret = inst->cfg->power_off(inst);
> > > +		spin_unlock(&drv->lock);
> > > +	}
> > > +	clk_disable_unprepare(inst->clk);
> > > +	clk_disable_unprepare(drv->clk);
> > > +	return ret;
> > > +}
> > > +
> > > +static struct phy_ops samsung_usb2_phy_ops = {
> > > +	.power_on	= samsung_usb2_phy_power_on,
> > > +	.power_off	= samsung_usb2_phy_power_off,
> > > +	.owner		= THIS_MODULE,
> > > +};
> > > +
> > > +static struct phy *samsung_usb2_phy_xlate(struct device *dev,
> > > +					struct of_phandle_args *args)
> > > +{
> > > +	struct samsung_usb2_phy_driver *drv;
> > > +
> > > +	drv = dev_get_drvdata(dev);
> > > +	if (!drv)
> > > +		return ERR_PTR(-EINVAL);
> > > +
> > > +	if (WARN_ON(args->args[0] >= drv->cfg->num_phys))
> > > +		return ERR_PTR(-ENODEV);
> > > +
> > > +	return drv->instances[args->args[0]].phy;
> > > +}
> > > +
> > > +static const struct of_device_id samsung_usb2_phy_of_match[] = {
> > > +#ifdef CONFIG_PHY_EXYNOS4210_USB2
> > > +	{
> > > +		.compatible = "samsung,exynos4210-usb2-phy",
> > > +		.data = &exynos4210_usb2_phy_config,
> > > +	},
> > > +#endif
> > > +#ifdef CONFIG_PHY_EXYNOS4212_USB2
> > > +	{
> > > +		.compatible = "samsung,exynos4212-usb2-phy",
> > > +		.data = &exynos4212_usb2_phy_config,
> > > +	},
> > > +#endif
> > > +	{ },
> > > +};
> >
> > I think we've had enough discussion about this approach. Let's get
> the
> > opinion of others too. Felipe? Greg?
> 
> Good idea.
> 
> > Summary:
> > We have two drivers PHY_EXYNOS4210_USB2 and PHY_EXYNOS4212_USB2 with
> > almost similar register map [1] and a samsung helper driver for these
> > two drivers.
> 
> I would not call them separate drivers. It's a single USB 2.0 driver
> with the option to include support for various SoCs. This patchset adds:
> Exynos 4210, Exynos 4212, Exynos 5250 and S5PCV210. I know that another
> person is working on supporting S3C6410.
> 
> > These two PHY drivers populate the function pointers in the helper
> > driver. So any phy_ops will first invoke the helper driver which will
> > then invoke the corresponding phy driver.
> >
> > [1] -> http://www.diffchecker.com/7yno1uvk
> 
> Come on, this diff only includes the registers part of the file.
> The following functions are also different:
> - exynos421*_rate_to_clk
> - exynos421*_isol
> - exynos421*_phy_pwr
> - exynos421*_power_on
> - exynos421*_power_on
> 
> It seems that the file is too large for the tool. But still this makes
> a false impression that only registers are different.
> 
> > Advantages:
> > * (more) clean and readable
> > * helper driver can be used with other PHY drivers which will be
> added
> > soon
> >
> > Disadvantages:
> > * code duplication
> 
> I would say that actually in this case less code is duplicated. Having
> Separate drivers would mean that most of the phy-samsung-usb2.c file
> has to be repeated. That is 240 times 4 (and surely more in the future,
> as this patchset adds support for 4 SoCs). Which is almost 1000 lines
> more.
> 
> >
> > Maybe having a helper driver makes sense when we have other samsung
> > PHY drivers added but not sure if it's needed here for
> EXYNOS4210_USB2
> > and
> > EXYNOS4212_USB2
> >
> > Need your inputs on what you think about this.
> 
> Yes, I would also welcome other people's opinions.
> 
> > > +
> > > +static int samsung_usb2_phy_probe(struct platform_device *pdev) {
> > > +	const struct of_device_id *match;
> > > +	const struct samsung_usb2_phy_config *cfg;
> > > +	struct clk *clk;
> > > +	struct device *dev = &pdev->dev;
> > > +	struct phy_provider *phy_provider;
> > > +	struct resource *mem;
> > > +	struct samsung_usb2_phy_driver *drv;
> > > +	int i;
> > > +
> > > +	if (!pdev->dev.of_node) {
> > > +		dev_err(dev, "This driver is required to be instantiated
> > from device tree\n");
> > > +		return -EINVAL;
> > > +	}
> > > +
> > > +	match = of_match_node(samsung_usb2_phy_of_match, pdev-
> > >dev.of_node);
> > > +	if (!match) {
> > > +		dev_err(dev, "of_match_node() failed\n");
> > > +		return -EINVAL;
> > > +	}
> > > +	cfg = match->data;
> > > +
> > > +	drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
> > > +		cfg->num_phys * sizeof(struct samsung_usb2_phy_instance),
> > GFP_KERNEL);
> > > +	if (!drv)
> > > +		return -ENOMEM;
> > > +
> > > +	dev_set_drvdata(dev, drv);
> > > +	spin_lock_init(&drv->lock);
> > > +
> > > +	drv->cfg = cfg;
> > > +	drv->dev = dev;
> > > +
> > > +	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > +	drv->reg_phy = devm_ioremap_resource(dev, mem);
> > > +	if (IS_ERR(drv->reg_phy)) {
> > > +		dev_err(dev, "Failed to map register memory (phy)\n");
> > > +		return PTR_ERR(drv->reg_phy);
> > > +	}
> > > +
> > > +	drv->reg_pmu = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
> > > +		"samsung,pmureg-phandle");
> > > +	if (IS_ERR(drv->reg_pmu)) {
> > > +		dev_err(dev, "Failed to map PMU registers (via syscon)\n");
> > > +		return PTR_ERR(drv->reg_pmu);
> > > +	}
> > > +
> > > +	if (drv->cfg->has_mode_switch) {
> > > +		drv->reg_sys = syscon_regmap_lookup_by_phandle(
> > > +				pdev->dev.of_node,
"samsung,sysreg-phandle");
> > > +		if (IS_ERR(drv->reg_sys)) {
> > > +			dev_err(dev, "Failed to map system registers (via
> > syscon)\n");
> > > +			return PTR_ERR(drv->reg_sys);
> > > +		}
> > > +	}
> > > +
> > > +	drv->clk = devm_clk_get(dev, "phy");
> > > +	if (IS_ERR(drv->clk)) {
> > > +		dev_err(dev, "Failed to get clock of phy controller\n");
> > > +		return PTR_ERR(drv->clk);
> > > +	}
> > > +
> > > +	for (i = 0; i < drv->cfg->num_phys; i++) {
> > > +		char *label = drv->cfg->phys[i].label;
> > > +		struct samsung_usb2_phy_instance *p = &drv->instances[i];
> > > +
> > > +		dev_dbg(dev, "Creating phy \"%s\"\n", label);
> > > +		p->phy = devm_phy_create(dev, &samsung_usb2_phy_ops, NULL);
> > > +		if (IS_ERR(p->phy)) {
> > > +			dev_err(drv->dev, "Failed to create usb2_phy
> > \"%s\"\n",
> > > +						label);
> > > +			return PTR_ERR(p->phy);
> > > +		}
> > > +
> > > +		p->cfg = &drv->cfg->phys[i];
> > > +		p->drv = drv;
> > > +		phy_set_drvdata(p->phy, p);
> > > +
> > > +		clk = devm_clk_get(dev, p->cfg->label);
> > > +		if (IS_ERR(clk)) {
> > > +			dev_err(dev, "Failed to get clock of \"%s\" phy\n",
> > > +
p->cfg->label);
> > > +			return PTR_ERR(clk);
> > > +		}
> > > +		p->clk = clk;
> > > +	}
> > > +
> > > +	phy_provider = devm_of_phy_provider_register(dev,
> > > +
samsung_usb2_phy_xlate);
> > > +	if (IS_ERR(phy_provider)) {
> > > +		dev_err(drv->dev, "Failed to register phy provider\n");
> > > +		return PTR_ERR(phy_provider);
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static struct platform_driver samsung_usb2_phy_driver = {
> > > +	.probe	= samsung_usb2_phy_probe,
> > > +	.driver = {
> > > +		.of_match_table	= samsung_usb2_phy_of_match,
> > > +		.name		= "samsung-usb2-phy",
> > > +		.owner		= THIS_MODULE,
> > > +	}
> > > +};
> > > +
> > > +module_platform_driver(samsung_usb2_phy_driver);
> > > +MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver");
> > > +MODULE_AUTHOR("Kamil Debski <k.debski@xxxxxxxxxxx>");
> > > +MODULE_LICENSE("GPL v2");
> > > +MODULE_ALIAS("platform:samsung-usb2-phy");
> > > +
> > > diff --git a/drivers/phy/phy-samsung-usb2.h
> > > b/drivers/phy/phy-samsung-usb2.h new file mode 100644 index
> > > 0000000..cd12477
> > > --- /dev/null
> > > +++ b/drivers/phy/phy-samsung-usb2.h
> > > @@ -0,0 +1,72 @@
> > > +/*
> > > + * Samsung SoC USB 1.1/2.0 PHY driver
> > > + *
> > > + * Copyright (C) 2013 Samsung Electronics Co., Ltd.
> > > + * Author: Kamil Debski <k.debski@xxxxxxxxxxx>
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > +modify
> > > + * it under the terms of the GNU General Public License version 2
> > > +as
> > > + * published by the Free Software Foundation.
> > > + */
> > > +
> > > +#ifndef _PHY_EXYNOS_USB2_H
> > > +#define _PHY_EXYNOS_USB2_H
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/io.h>
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/of_address.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/spinlock.h>
> > > +
> > > +#define KHZ 1000
> > > +#define MHZ (KHZ * KHZ)
> > > +
> > > +struct samsung_usb2_phy_driver;
> > > +struct samsung_usb2_phy_instance;
> > > +struct samsung_usb2_phy_config;
> > > +
> > > +struct samsung_usb2_phy_instance {
> > > +	struct samsung_usb2_phy_driver *drv;
> > > +	struct phy *phy;
> > > +	const struct samsung_usb2_common_phy *cfg;
> > > +	char enabled;
> > > +	struct clk *clk;
> > > +	u32 clk_reg_val;
> > > +	unsigned long rate;
> > > +};
> > > +
> > > +struct samsung_usb2_phy_driver {
> > > +	struct device *dev;
> > > +	spinlock_t lock;
> > > +	void __iomem *reg_phy;
> > > +	struct regmap *reg_sys;
> > > +	struct regmap *reg_pmu;
> > > +	const struct samsung_usb2_phy_config *cfg;
> > > +	struct clk *clk;
> > > +	struct samsung_usb2_phy_instance instances[0]; };
> > > +
> > > +struct samsung_usb2_common_phy {
> > > +	char *label;
> > > +	unsigned int id;
> > > +	int (*rate_to_clk)(unsigned long, u32 *);
> > > +	int (*power_on)(struct samsung_usb2_phy_instance *);
> > > +	int (*power_off)(struct samsung_usb2_phy_instance *); };
> > > +
> > > +
> > > +struct samsung_usb2_phy_config {
> > > +	int num_phys;
> > > +	const struct samsung_usb2_common_phy *phys;
> > > +	char has_mode_switch;
> >
> > u8 instead?
> 
> Do we really need to specify that we need 8bits? Why do you think char
> is wrong?
> 
> Please read this paragraph from LDD3:
> "Sometimes kernel code requires data items of a specific size, perhaps
> to match predefined binary structures,* to communicate with user space,
> or to align data within structures by inserting "padding" fields (but
> refer to the section "Data Alignment" for information about alignment
> issues)."
> Chapter 11, page 290 http://lwn.net/images/pdf/LDD3/ch11.pdf
> 
> has_mode_switch is only a flag 0 or 1. Never written anywhere in
> hardware registers. Used in an if somewhere in code. Give me a good
> reason why do you think it should be explicitly 8 bit long.
> 

On the second thought, we both are wrong as bool would be the best choice
here. Have a good weekend.

Best wishes,
-- 
Kamil Debski
Samsung R&D Institute Poland


--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux