Re: VIA chipset not supported by xhci drivers?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Nov 27, 2013 at 03:00:40PM -0700, Philip Prindeville wrote:
> I wasn’t able to get the 7-port Orico controller working, so I swapped
> it out for a 4-port (single chip) Anker instead.
> 
> $ sudo lspci -v -s 03:00.0
> 03:00.0 USB controller: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller (rev 03) (prog-if 30 [XHCI])
> 	Subsystem: VIA Technologies, Inc. VL80x xHCI USB 3.0 Controller
> 	Flags: bus master, fast devsel, latency 0, IRQ 43
> 	Memory at fbdff000 (32-bit, non-prefetchable) [size=4K]
> 	Capabilities: [80] Power Management version 3
> 	Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit+
> 	Capabilities: [c4] Express Endpoint, MSI 00
> 	Capabilities: [100] Advanced Error Reporting
> 	Kernel driver in use: xhci_hcd

See the xhci_hcd driver properly binds to this, it goes off of the PCI
class codes, not the product id.

>> This time when I tried to plug in a Western Digital Passport drive, I got:
> 
> Nov 26 15:07:27 builder kernel: [864975.137714] usb 9-1: Device not responding to set address.
> Nov 26 15:07:27 builder kernel: [864975.338699] usb 9-1: Device not responding to set address.
> Nov 26 15:07:28 builder kernel: [864975.539506] usb 9-1: device not accepting address 43, error -71
> Nov 26 15:07:28 builder kernel: [864976.293815] usb 9-1: Device not responding to set address.
> Nov 26 15:07:29 builder kernel: [864976.494778] usb 9-1: Device not responding to set address.
> Nov 26 15:07:29 builder kernel: [864976.695594] usb 9-1: device not accepting address 45, error -71
> ...
> Nov 26 15:09:07 builder kernel: [865074.813213] usb 9-1: Device not responding to set address.
> Nov 26 15:09:07 builder kernel: [865075.014135] usb 9-1: Device not responding to set address.
> Nov 26 15:09:07 builder kernel: [865075.214942] usb 9-1: device not accepting address 89, error -71
> Nov 26 15:09:08 builder kernel: [865075.969269] usb 9-1: Device not responding to set address.
> Nov 26 15:09:08 builder kernel: [865076.170220] usb 9-1: Device not responding to set address.
> Nov 26 15:09:09 builder kernel: [865076.371024] usb 9-1: device not accepting address 91, error -71

But that's not good at all.

Does 3.12 work better for you?

thanks,

greg k-h
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux