Re: [PATCH RFC 1/1] usb: Tell xhci when usb data might be misaligned

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat, Feb 1, 2014 at 3:00 AM, Sarah Sharp
<sarah.a.sharp@xxxxxxxxxxxxxxx> wrote:
> On Fri, Jan 31, 2014 at 08:17:58AM +0800, Ming Lei wrote:
>> On Fri, Jan 31, 2014 at 6:15 AM, Sarah Sharp
>> <sarah.a.sharp@xxxxxxxxxxxxxxx> wrote:
>> > On Thu, Jan 30, 2014 at 10:50:21PM +0100, Bjørn Mork wrote:
>> >> FWIW, the plan looks fine to me.  Just adding a couple of hints to
>> >> simplify the implementation.
>> >>
>> >> Sarah Sharp <sarah.a.sharp@xxxxxxxxxxxxxxx> writes:
>> >>
>> >> > Let's do this fix the right way, instead of wall papering over the
>> >> > issue.  Here's what we should do:
>> >> >
>> >> > 1. Disable scatter-gather for the ax88179_178a driver when it's under an
>> >> >    xHCI host.
>> >>
>> >> No need to make this conditional.  SG is only enabled in the
>> >> ax88179_178a driver if udev->bus->no_sg_constraint is true, so it
>> >> applies only to xHCI hosts in the first place.
>> >
>> > Ah, so you're suggesting just reverting commit
>> > 3804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a: enable
>> > tso if usb host supports sg dma"?
>>
>> If I understand the problem correctly, the current issue is that xhci driver
>> doesn't support the arbitrary dma length not well, but per XHCI spec, it
>> should be supported, right?
>>
>> If the above is correct, reverting the commit isn't correct since there isn't
>> any issue about the commit, so I suggest to disable the flag in xhci
>> for the buggy devices, and it may be enabled again if the problem is fixed.
>
> Ok, I like that plan, since it means I don't have to touch any
> networking code to fix this. :)
>
> I believe that means we'll have to disable the flag for all 1.0 xHCI
> hosts, since those are the ones that need TD fragments.
>
>> >> > 2. Revert the following commits:
>> >> >    f2d9b991c549 xhci: Set scatter-gather limit to avoid failed block writes.
>> >> >    d6c9ea9069af xhci: Avoid infinite loop when sg urb requires too many trbs
>> >> >    35773dac5f86 usb: xhci: Link TRB must not occur within a USB payload burst
>> >> >
>> >> > 3. Dan and Mathias can work together to come up with an overall plan to
>> >> >    change the xHCI driver architecture to be fully compliant with the TD
>> >> >    fragment rules.  That can be done over the next few kernel releases.
>> >> >
>> >> > The end result is that we don't destabilize storage or break userspace
>> >> > USB drivers, we don't break people's xHCI host controllers,
>> >> > the ax88179_178a USB ethernet devices still work under xHCI (a bit with
>> >> > worse performance), and other USB ethernet devices still get the
>> >> > performance improvement introduced in 3.12.
>> >>
>> >> No other usbnet drivers has enabled SG...  Which is why you have only
>> >> seen this problem with the ax88179_178a devices.  So there is no
>> >> performance improvement to keep.
>>
>> In my test environment, the patch does improve both throughput and
>> cpu utilization, if you search the previous email for the patch, you can
>> see the data.

With SG enabled, for the iperf client test case, the average urb size
for transmission will be increased from ~1500 to ~20K bytes in my
test case:

   iperf -c $SRV -t 30 -P 4 -w 128K

So I am wondering you guys do not care the improvement, maybe
the CPU is powerful enough to not degrade throughout&cpu
utilization not much, but there is still the potential CPU wakeup issue,
which means extra CPU power consumption might be introduced
after disabling SG for usbnet.

>
> Right, I did see the performance improvement note in that commit.  Do
> you know if the ARM A15 dual core board was using a 0.96 xHCI host, or a
> 1.0 host?  You can find out by reloading the xHCI driver with dynamic
> debugging turned on:
>
> # sudo modprobe xhci_hcd dyndbg

Looks I can't find the parameter 'dyndbg' for xhci_hcd.

> and then look for lines like:
>
> [25296.765767] xhci_hcd 0000:00:14.0: HCIVERSION: 0x100

I change xhci_dbg.c manually with below:

diff --git a/drivers/usb/host/xhci-dbg.c b/drivers/usb/host/xhci-dbg.c
index b016d38..1ae1966 100644
--- a/drivers/usb/host/xhci-dbg.c
+++ b/drivers/usb/host/xhci-dbg.c
@@ -66,7 +66,7 @@ static void xhci_print_cap_regs(struct xhci_hcd *xhci)
                        (unsigned int) temp);
        xhci_dbg(xhci, "CAPLENGTH: 0x%x\n",
                        (unsigned int) HC_LENGTH(temp));
-       xhci_dbg(xhci, "HCIVERSION: 0x%x\n",
+       dev_info(xhci_to_hcd(xhci)->self.controller, "HCIVERSION: 0x%x\n",
                        (unsigned int) HC_VERSION(temp));

and got the below output:

[tom@ming ~]$ dmesg | grep HCIVERSION
xhci-hcd xhci-hcd.2.auto: HCIVERSION: 0x100

Thanks,
--
Ming Lei
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Media]     [Linux Input]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Old Linux USB Devel Archive]

  Powered by Linux