|
|
| [Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index] |
arun b wrote: > Thank you for the quick response... > > Ok I will have to check if the pppd is available in the remote (server > )device, > Now the current availabel options for remote device are Alctel-ISAM > or Dslam-Dlink where my ATM path terminates. > let me verify this... Oh, I assumed your server was a Linux box with pppd etc. If not, we won't be able to help you with server config here. > Again to clear the confusion.... > yes with above remote devices I have tested for PPPoE on ATM > can i call this test as PPPoEoA !!!!! Perhaps you mean PPPoE over an RFC1483 bridged encap ATM link? And now you're trying to get PPP working over a VC-muxed ATM connection. > > -Arun > > > > On Wed, Jun 2, 2010 at 10:24 PM, James Chapman <jchapman@xxxxxxxxxxx> wrote: >> arun b wrote: >>> Hi, >>> Thanks for the info >>> First of all let me try to clear your confusion .. >>> 1) at the client side as i already told you its linux-box and i am >>> running pppd (2.4) >>> ie. pppd plugin pppoatm.so 9.45 user xxxxxx password xxxxxx >>> >>> now this box send LCP packets 10 times and the pppd terminates. as >>> there is no responder.. >>> 2) Now I need to setup responder (PPPoA-server i belive) my self >>> similar to PPPoE-server in the case of pppoe test linuxPC. >>> >>> so if you know about server pls pass me the info >> At the server >> >> pppd plugin pppoatm.so 9.45 192.168.42.42:192.168.42.43 passive >> >> Run this on the server before starting the client. Adjust IP addresses >> as required. >> >>> Also we have alctel-iSAM which has only pppoa-relay and id doesnot >>> have server ......! >> What is pppoa-relay? Are you confusing PPPoE and PPPoA? >> >> What role does the Alcatel iSAM box play in your network? Is it between >> the Linux PPPoA client and Linux PPPoA server? If so, how does it map >> ingress/egress ATM VCs? Is it configured to pass the ATM traffic correctly? >> >>> >>> -Arun >>> >>> >>> >>> >>> >>> >>> On Wed, Jun 2, 2010 at 7:56 PM, James Carlson <carlsonj@xxxxxxxxxxxxxxx> wrote: >>>> arun b wrote: >>>>> On Wed, Jun 2, 2010 at 4:27 PM, James Carlson <carlsonj@xxxxxxxxxxxxxxx> wrote: >>>>>> But I think it's probably time to take a step back and ask the obvious >>>>>> question: can you tell us what you've got (in terms of hardware, >>>>>> software, and operational environment) and what you're trying to do (in >>>>>> as much high-level detail as possible)? >>>>> NO I am not building it for Dslam-box. well I want to run PPPoA server >>>>> at remote side device where ATM path terminates. >>>>> I am executing this is "pppd plugin pppoatm.so 0.80 >>>>> 192.168.1.1:192.168.1.2 passive" on my client(linux-box). >>>> "passive" is a slightly surprising option to see on the "client" side of >>>> the connection. Are you sure that's what you want? And are you sure >>>> that 0.80 are the right VPI/VCI pair for the connection? >>>> >>>> There are two broad classes of problems that show up here: either the >>>> ATM link isn't working, or the PPP link on top is misconfigured. What >>>> do you actually see when you run pppd? Have you tried running with the >>>> "debug" option enabled? What log messages are produced? >>>> >>>> If pppd is timing out in LCP with "too many" Configure-Request messages, >>>> then the likely culprit is the ATM configuration. Otherwise, PPP might >>>> be involved; possibly missing authentication or L3 address information. >>>> >>>>> |-| RJ-11 connector "pppd plugin pppoatm.so 0.80 >>>>> 192.168.1.1:192.168.1.2 passive" >>>> It should be obvious, but the connection between these two machines >>>> _must_ be ATM, and _not_ Ethernet. >>>> >>>>> Here the server device and the configuration are unknown to me. Could >>>>> you help in choose the server device (Dslam, iSam like..), and >>>>> enabling it. >>>> If you're not the administrator for the remote end, then I have no idea >>>> how you might go about enabling it. Won't you have to drive down to >>>> your ISP's offices and break in first? >>>> >>>> Or are you planning to set up your own PPPoA server ... ? >>>> >>>> I'm confused by what you're saying here. >>>> >>>>> James, >>>>> To your question: >>>>> I have MIPS based network device currently with me. And am exploring >>>>> all PPPoX-Client(oe/oa/...) configuration. Where I am already able to >>>>> test pppoe, pppoeonATm, and wanted start on PPPoS. - so that we can >>>>> port this solution to any of the h/w. >>>>> Now got stoped at PPPoA !!! >>>> Do you have an ATM link to a system that runs PPPoA? If so, then do you >>>> have configuration information (particularly VPI/VCI) for that link? Is >>>> it a nailed-up VPI/VCI pair or is it "dialed" using UNI signaling? >>>> >>>> -- >>>> James Carlson 42.703N 71.076W <carlsonj@xxxxxxxxxxxxxxx> >>>> >> >> -- >> James Chapman >> Katalix Systems Ltd >> http://www.katalix.com >> Catalysts for your Embedded Linux software development >> >> > -- James Chapman Katalix Systems Ltd http://www.katalix.com Catalysts for your Embedded Linux software development -- To unsubscribe from this list: send the line "unsubscribe linux-ppp" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html