Re: [PATCH v7 00/11] usb: musb: adding multi instance support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

On 03.08.2012 02:54, B, Ravi wrote:
>> On 02.08.2012 14:12, Ravi Babu wrote:
>>> This series of patches adds,
>>> a) Multi instances support in musb driver
>>> b) DT support for musb_dsps glue layer
>>> c) DT support for NOP transceiver
>>>
>>> AM33xx and TI81xx has dual musb controller and has two usb 
>> PHY of same type.
>>> This patch series uses 'phandle' based API 
>>> devm_usb_get_phy_by_phandle() to get the PHY of same type. This API 
>>> support is being added by Kishon's patch discussed at [1]
>>>
>>> The series applies to linux-omap (master branch)
>>> 	+ Vaibhav baseport patches on his tree at [3]
>>> 	+ Kishon's multi phy patches on Felipe's branch 'xceiv'
>>> 	+ Kishon's patch on phandle at [1]
>>> 	+ AM33xx musb glue compile and bugfix patches at [4], 
>> [5], [6] and [7]
>>> 	+ Damodar's recent patch at [2]
>>>
>>> and have been tested on Beaglebone board.
> 
> Have you applied the above patches before applying these patches.

Somehow, I was missing some of Ajay's patches. I resolved that, and now
the series applied.

However, I needed to add a phandle "usb0-phy = <&usb0_phy>" to the
usb_otg_hs DTSI block, otherwise devm_usb_get_phy_by_phandle() in
drivers/usb/musb/musb_dsps.c would fail. Is that correct? I can't seem
to find that in your patches.

With this addition, I see the following:

[    1.782180] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[    1.809966] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[    1.819068] musb-hdrc musb-hdrc.0: new USB bus registered, assigned
bus number 1
[    1.827970] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.835184] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[    1.842818] usb usb1: Product: MUSB HDRC host driver
[    1.848031] usb usb1: Manufacturer: Linux
3.6.0-rc1-00038-g8a1ec8f-dirty musb-hcd
[    1.855933] usb usb1: SerialNumber: musb-hdrc.0
[    1.866913] hub 1-0:1.0: USB hub found
[    1.871192] hub 1-0:1.0: 1 port detected
[    1.878106] musb-hdrc musb-hdrc.0: USB Host mode controller at
d08c0000 using PIO, IRQ 18

... but no USB functions. Also, every two seconds, the following message
is printed:

[   11.036608] musb_bus_suspend 2308: trying to suspend as a_wait_vrise
while active
[   13.044811] musb_bus_suspend 2308: trying to suspend as a_wait_vrise
while active
[   15.052196] musb_bus_suspend 2308: trying to suspend as a_wait_vrise
while active


Anything obvious that I'm missing?


Thanks,
Daniel
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Photo]     [Yosemite News]    [Yosemite Photos]    [Free Online Dating]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux