Re: [PATCHv2 00/16] [FS, MM, block, MMC]: eMMC High Priority Interrupt Feature

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

On Wed, May 9, 2012 at 6:15 AM, Minchan Kim <minchan@xxxxxxxxxx> wrote:
> On 05/09/2012 01:31 AM, S, Venkatraman wrote:
>
>> On Tue, May 8, 2012 at 1:16 PM, Minchan Kim <minchan@xxxxxxxxxx> wrote:
>>> On 05/03/2012 11:22 PM, Venkatraman S wrote:
>>>
>>>> Standard eMMC (Embedded MultiMedia Card) specification expects to execute
>>>> one request at a time. If some requests are more important than others, they
>>>> can't be aborted while the flash procedure is in progress.
>>>>
>>>> New versions of the eMMC standard (4.41 and above) specfies a feature
>>>> called High Priority Interrupt (HPI). This enables an ongoing transaction
>>>> to be aborted using a special command (HPI command) so that the card is ready
>>>> to receive new commands immediately. Then the new request can be submitted
>>>> to the card, and optionally the interrupted command can be resumed again.
>>>>
>>>> Some restrictions exist on when and how the command can be used. For example,
>>>> only write and write-like commands (ERASE) can be preempted, and the urgent
>>>> request must be a read.
>>>>
>>>> In order to support this in software,
>>>> a) At the top level, some policy decisions have to be made on what is
>>>> worth preempting for.
>>>>       This implementation uses the demand paging requests and swap
>>>> read requests as potential reads worth preempting an ongoing long write.
>>>>       This is expected to provide improved responsiveness for smarphones
>>>> with multitasking capabilities - example would be launch a email application
>>>> while a video capture session (which causes long writes) is ongoing.
>>>
>>>
>>> Do you have a number to prove it's really big effective?
>>
>> What type of benchmarks would be appropriate to post ?
>> As you know, the response time of a card would vary depending on
>> whether the flash device
>> has enough empty blocks to write into and doesn't have to resort to GC during
>> write requests.
>> Macro benchmarks like iozone etc would be inappropriate here, as they won't show
>> the latency effects of individual write requests hung up doing page
>> reclaim, which happens
>> once in a while.
>
>
> We don't have such special benchmark so you need time to think how to prove it.
> IMHO, you can use run-many-x-apps.sh which checks elapsed time to activate programs
> by posting by Wu long time ago.
>
> http://www.spinics.net/lists/linux-mm/msg09653.html
>
> Of course, your eMMC is used above 80~90% for triggering GC stress and
> your memory should be used up by dirty pages to happen reclaim.
>
>
>>>
>>> What I have a concern is when we got low memory situation.
>>> Then, writing speed for page reclaim is important for response.
>>> If we allow read preempt write and write is delay, it means read path takes longer time to
>>> get a empty buffer pages in reclaim. In such case, it couldn't be good.
>>>
>>
>> I agree. But when writes are delayed anyway as it exceeds
>> hpi_time_threshold (the window
>> available for invoking HPI), it means that the device is in GC mode
>> and either read or write
>> could be equally delayed.  Note that even in case of interrupting a
>> write, a single block write
>> (which usually is too short to be interrupted, as designed) is
>> sufficient for doing a page reclaim,
>> and further write requests (including multiblock) would not be subject
>> to HPI, as they will
>> complete within the average time.
>
>
> My point is that it would be better for read to not preempt write-for-page_reclaim.
> And we can identify it by PG_reclaim. You can get the idea.
>
> Anyway, HPI is only feature of a device of many storages and you are requiring modification
> of generic layers although it's not big. So for getting justification and attracting many
> core guys(MM,FS,BLOCK), you should provide data at least.
>
Hi Kim,
 Apologies for a delayed response. I am studying your suggestions and
will get back with
some changes and also some profiling data.
Regards,
Venkat.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Photo]     [Yosemite News]    [Yosemite Photos]    [Free Online Dating]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux