RE: [PATCH v4 01/39] ARM: OMAP2+: gpmc: driver conversion

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Jon,

On Fri, May 04, 2012 at 21:57:10, Hunter, Jon wrote:
> > -	gpmc_write_reg(GPMC_SYSCONFIG, l);
> > -	gpmc_mem_init();
> > +	switch (conf & GPMC_WAITPIN_MASK) {
> > +	case GPMC_WAITPIN_0:
> > +		idx =  GPMC_WAITPIN_IDX0;
> > +		break;
> > +	case GPMC_WAITPIN_1:
> > +		idx =  GPMC_WAITPIN_IDX1;
> > +		break;
> > +	case GPMC_WAITPIN_2:
> > +		idx =  GPMC_WAITPIN_IDX2;
> > +		break;
> > +	case GPMC_WAITPIN_3:
> > +		idx =  GPMC_WAITPIN_IDX3;
> > +		break;
> > +	/* no waitpin */
> > +	case 0:
> > +		break;
> > +	default:
> > +		dev_err(gpmc->dev, "multiple waitpins selected on CS:%u\n", cs);
> > +		return -EINVAL;
> > +		break;
> > +	}
> 
> Why not combined case 0 and default? Both are invalid configurations so
> just report invalid selection.

Case 0 is not invalid, a case where waitpin is not used, default refers
to when a user selects multiple waitpins wrongly.

> 
> >  
> > -	/* initalize the irq_chained */
> > -	irq = OMAP_GPMC_IRQ_BASE;
> > -	for (cs = 0; cs < GPMC_CS_NUM; cs++) {
> > -		irq_set_chip_and_handler(irq, &dummy_irq_chip,
> > -						handle_simple_irq);
> > -		set_irq_flags(irq, IRQF_VALID);
> > -		irq++;
> > +	switch (conf & GPMC_WAITPIN_POLARITY_MASK) {
> > +	case GPMC_WAITPIN_ACTIVE_LOW:
> > +		polarity = LOW;
> > +		break;
> > +	case GPMC_WAITPIN_ACTIVE_HIGH:
> > +		polarity = HIGH;
> > +		break;
> > +	/* no waitpin */
> > +	case 0:
> > +		break;
> > +	default:
> > +		dev_err(gpmc->dev, "waitpin polarity set to low & high\n");
> > +		return -EINVAL;
> > +		break;
> >  	}
> 
> Again, combine case 0 and default as these are invalid.

Similar to above

> 
> > +		if (gd->have_waitpin) {
> > +			if (gd->waitpin != idx ||
> > +					gd->waitpin_polarity != polarity) {
> > +				dev_err(gpmc->dev, "error: conflict: waitpin %u with polarity %d on device %s.%d\n",
> > +					gd->waitpin, gd->waitpin_polarity,
> > +					gd->name, gd->id);
> > +				return -EBUSY;
> > +			}
> > +		} else {
> 
> Don't need the else as you are going to return in the above.

Not always, only in case of error

> 
> > +			gd->have_waitpin = true;
> > +			gd->waitpin = idx;
> > +			gd->waitpin_polarity = polarity;
> > +		}
> > +
> > +		l &= ~GPMC_CONFIG1_WAIT_PIN_SEL_MASK;
> > +		l |= GPMC_CONFIG1_WAIT_PIN_SEL(idx);
> > +		gpmc_cs_write_reg(cs, GPMC_CS_CONFIG1, l);
> > +	} else if (polarity) {
> > +		dev_err(gpmc->dev, "error: waitpin polarity specified with out wait pin number on device %s.%d\n",
> > +							gd->name, gd->id);
> > +		return -EINVAL;
> 
> Drop this else-if. The above switch statements will report the bad
> configuration. This seems a bit redundant.

This is required as switch statements will not report error if polarity
is specified, w/o waitpin to be used.

Regards
Afzal
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux