Re: [PATCHv2 8/8] arm: omap3: prevent per_clkdm from attempting manual domain transitions

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Tero Kristo <t-kristo@xxxxxx> writes:

> On Thu, 2012-02-16 at 09:31 -0800, Kevin Hilman wrote:
>> Tero Kristo <t-kristo@xxxxxx> writes:
>> 
>> > On Thu, 2012-02-16 at 21:15 +0530, Shilimkar, Santosh wrote:
>> >> On Thu, Feb 16, 2012 at 8:53 PM, Tero Kristo <t-kristo@xxxxxx> wrote:
>> >> > On Thu, 2012-02-16 at 15:15 +0200, Tero Kristo wrote:
>> >> >> On Thu, 2012-02-16 at 15:27 +0530, Shilimkar, Santosh wrote:
>> >> >> > On Thu, Feb 16, 2012 at 2:27 PM, Tero Kristo <t-kristo@xxxxxx> wrote:
>> >> >> > > On Wed, 2012-02-15 at 11:37 -0800, Kevin Hilman wrote:
>> >> >> > >> Tero Kristo <t-kristo@xxxxxx> writes:
>> >> >> > >>
>> >> >> > >> > Attempting this will cause problems especially with off-mode enabled.
>> >> >> > >>
>> >> >> > >> Please be more verbose about the problems seen, and the root cause(s).
>> >> >> > >>
>> >> >> > >
>> >> >> > > I was actually looking forward for some help with this commit message,
>> >> >> > > as I am still not quite sure what is going on in here. :) Here is the
>> >> >> > > log for suspend (btw, cam_pwrdm does not go to off in mainline yet, but
>> >> >> > > I think that is probably fixed by the patch from Paul,
>> >> >> > > omap_set_pwrdm_state() does not work properly.) The warning comes out
>> >> >> > > after wakeup from off-mode, and it is triggered by the disabling of
>> >> >> > > autodeps before off-mode entry.
>> >> >> > >
>> >> >> > This mostly indicates that one of the per clock-domain module
>> >> >> > clock turning ON seems to be not working well with auto deps
>> >> >> > disabled. This leads to interconnect violation.
>> >> >> >
>> >> >> > if not tried already, can you put the per_clockdomain in SW_WKUP
>> >> >> > in the low power code early resume path and see if this
>> >> >> > error goes away.
>> >> >>
>> >> >> This seems to get rid of the dump also. It looks like some driver resume
>> >> >> is not behaving nicely, I am trying to pinpoint the culprit currently
>> >> >> and see whether it can provide more info.
>> >> >
>> >> > Okay, I have some more info about this now.
>> >> >
>> >> > What happens is that when entering off-mode, PER domain remains OFF even
>> >> > during the execution of the exit phase from omap_sram_idle. Adding a
>> >> > manual SW_WKUP it comes up and there are no issues. If autodeps are
>> >> > enabled on the domain, it comes back from off mode as active.
>> >> >
>> >> > Looking further in the code, we have this at the end of omap_sram_idle:
>> >> >
>> >> >        if (per_next_state < PWRDM_POWER_ON) {
>> >> >                per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm);
>> >> >                omap2_gpio_resume_after_idle();
>> >> >                wake_per();
>> >> >                if (per_prev_state == PWRDM_POWER_OFF)
>> >> >                        omap3_per_restore_context();
>> >> >        }
>> >> >
>> >> > ... which seems to assume that per domain is on. Gpio code does not
>> >> > control any clocks currently, as it only requires the interface clock to
>> >> > be on, and as this is autoidled....
>> >> >
>> >> > Any comments how we should handle this? Shall we just keep these two
>> >> > patches for handling this or add some different hackery for the gpio
>> >> > issue?
>> >> >
>> >> Good. I thought too that issue will disappear.
>> >> The issue is pretty clear. Technically every driver pm_runtime() code should
>> >> be able to manage a clock->clockdomain->power domain power up/down
>> >> sequence. That should work without auto deps.
>> >> 
>> >> Do you narrowed down which driver resume is creating the dump ?
>> >> UART , GPIO ?
>> >
>> > It is the gpio base stuff called from omap_sram_idle(), basically the
>> > restore context part. If I force enable per domain before the code
>> > snippet before, there is no dump, but if it is done after, I get the
>> > dump.
>> >
>> > The thing is that gpio driver doesn't currently have this kind of
>> > mechanism for the restore context part, at least not on omap3 due to
>> > above clocking issue (only autoidled interface clock is used.)
>> 
>> I'm not sure if it fully addresses this, but Tarun's series converts
>> GPIO to runtime PM.
>> 
>> Can you try with Tarun's series.  See the for_3.4/gpio_cleanup_fixes_v9
>> branch here:
>> git://gitorious.org/~tarunkanti/omap-sw-develoment/tarunkantis-linux-omap-dev.git
>
> It does something for the issue, but I still get this during suspend to
> off:
>
> [   11.284973] PM: Syncing filesystems ... done.
> [   11.379241] Freezing user space processes ... (elapsed 0.02 seconds)
> done.
> [   11.408233] Freezing remaining freezable tasks ... (elapsed 0.02
> seconds) don
> e.
> [   11.439239] Suspending console(s) (use no_console_suspend to debug)
> [   11.564178] PM: suspend of devices complete after 115.506 msecs
> [   11.567382] PM: late suspend of devices complete after 3.204 msecs
> [   11.567443] Disabling non-boot CPUs ...
> [   12.004089] Powerdomain (cam_pwrdm) didn't enter target state 0
> [   12.004119] Could not enter target state in pm_suspend
> [   12.009368] PM: early resume of devices complete after 4.944 msecs
> [   12.436645] PM: resume of devices complete after 426.086 msecs
> [   12.480285] Restarting tasks ... done.
> /sys/kernel/debu[   12.488433] ------------[ cut here ]------------
> [   12.494415] WARNING: at arch/arm/mach-omap2/omap_hwmod.c:1604 _idle
> +0x164/0x1
> 7c()
> [   12.502258] omap_hwmod: gpio6: idle state can only be entered from
> enabled st
> ate
> [   12.509979] Modules linked in:
> [   12.513214] [<c001bcd0>] (unwind_backtrace+0x0/0xf4) from
> [<c0042968>] (warn_
> slowpath_common+0x4c/0x64)
> [   12.523071] [<c0042968>] (warn_slowpath_common+0x4c/0x64) from
> [<c0042a14>] (
> warn_slowpath_fmt+0x30/0x40)
> [   12.533081] [<c0042a14>] (warn_slowpath_fmt+0x30/0x40) from
> [<c0028d68>] (_id
> le+0x164/0x17c)
> [   12.541931] [<c0028d68>] (_idle+0x164/0x17c) from [<c00298b0>]
> (omap_hwmod_id
> le+0x28/0x3c)
> [   12.550567] [<c00298b0>] (omap_hwmod_idle+0x28/0x3c) from
> [<c003c664>] (omap_
> device_idle_hwmods+0x24/0x3c)
> [   12.560699] [<c003c664>] (omap_device_idle_hwmods+0x24/0x3c) from
> [<c003c898>
> ] (_omap_device_deactivate+0xa4/0x138)
> [   12.571594] [<c003c898>] (_omap_device_deactivate+0xa4/0x138) from
> [<c003c954
>>] (omap_device_idle+0x28/0x54)
> [   12.581909] [<c003c954>] (omap_device_idle+0x28/0x54) from
> [<c003c99c>] (_od_
> runtime_suspend+0x1c/0x24)
> [   12.591735] [<c003c99c>] (_od_runtime_suspend+0x1c/0x24) from
> [<c02c5010>] (_
> _rpm_callback+0x2c/0x78)
> [   12.601379] [<c02c5010>] (__rpm_callback+0x2c/0x78) from [<c02c54d0>]
> (rpm_su
> spend+0x264/0x6c4)
> [   12.610504] [<c02c54d0>] (rpm_suspend+0x264/0x6c4) from [<c02c6998>]
> (__pm_ru
> ntime_suspend+0x5c/0x74)
> [   12.620178] [<c02c6998>] (__pm_runtime_suspend+0x5c/0x74) from
> [<c02731a4>] (
> omap2_gpio_prepare_for_idle+0x50/0x64)
> [   12.631103] [<c02731a4>] (omap2_gpio_prepare_for_idle+0x50/0x64) from
> [<c002b
> d30>] (omap_sram_idle+0xa0/0x3b0)
> [   12.641571] [<c002bd30>] (omap_sram_idle+0xa0/0x3b0) from
> [<c002c1d8>] (omap3
> _pm_idle+0x60/0x178)
> [   12.650848] [<c002c1d8>] (omap3_pm_idle+0x60/0x178) from [<c0015c10>]
> (cpu_id
> le+0xc4/0x108)
> [   12.659606] [<c0015c10>] (cpu_idle+0xc4/0x108) from [<c0626828>]
> (start_kerne
> l+0x2b0/0x304)
> [   12.668365] ---[ end trace 441b8fea2b56dcb1 ]---
>
>
> Also, this goes away if I manually force wakeup for the per domain, so
> this might be caused by some additional latency.
>

What platform are you testing on?

When I test Tarun's series with off-mode on 3430/n900 suspend/resume
works fine.  But when I add your v2 series, it never comes out of
suspend, and I don't get a kernel dump either.

Can you debug this a little further so we can explain what's going on
here?

Thanks,

Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Photo]     [Yosemite News]    [Yosemite Photos]    [Free Online Dating]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux