Re: [PATCH v4 5/9] ARM: dts: omap3-overo: Add HSUSB PHY

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Florian,

On 03/07/2014 09:22 PM, Florian Vaussard wrote:
> Add the High-Speed USB PHY.
> 
> Signed-off-by: Florian Vaussard <florian.vaussard@xxxxxxx>
> ---
>  arch/arm/boot/dts/omap3-overo-base.dtsi  | 44 ++++++++++++++++++++++++++++++++
>  arch/arm/boot/dts/omap3-overo-storm.dtsi | 16 ++++++++++++
>  arch/arm/boot/dts/omap3-overo.dtsi       | 16 ++++++++++++
>  3 files changed, 76 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi
> index edac70e..13d1ad2 100644
> --- a/arch/arm/boot/dts/omap3-overo-base.dtsi
> +++ b/arch/arm/boot/dts/omap3-overo-base.dtsi
> @@ -30,6 +30,24 @@
>  		ti,codec = <&twl_audio>;
>  	};
>  
> +	/* HS USB Port 2 Power */
> +	hsusb2_power: hsusb2_power_reg {
> +		compatible = "regulator-fixed";
> +		regulator-name = "hsusb2_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio6 8 0>;				/* gpio_168: vbus enable */
> +		startup-delay-us = <70000>;
> +		enable-active-high;
> +	};
> +
> +	/* HS USB Host PHY on PORT 2 */
> +	hsusb2_phy: hsusb2_phy {
> +		compatible = "usb-nop-xceiv";
> +		reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>;	/* gpio_183 */
> +		vcc-supply = <&hsusb2_power>;
> +	};
> +
>  	/* Regulator to trigger the nPoweron signal of the Wifi module */
>  	w3cbw003c_npoweron: regulator-w3cbw003c-npoweron {
>  		compatible = "regulator-fixed";
> @@ -64,6 +82,11 @@
>  };
>  
>  &omap3_pmx_core {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +			&hsusb2_pins
> +	>;
> +
>  	uart2_pins: pinmux_uart2_pins {
>  		pinctrl-single,pins = <
>  			OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1)	/* mcbsp3_dx.uart2_cts */
> @@ -116,6 +139,19 @@
>  			OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4)		/* uart3_rts_sd.gpio_164 */
>  		>;
>  	};
> +
> +	hsusb2_pins: pinmux_hsusb2_pins {
> +		pinctrl-single,pins = <
> +			OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi1_cs3.hsusb2_data2 */
> +			OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_clk.hsusb2_data7 */
> +			OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_simo.hsusb2_data4 */
> +			OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_somi.hsusb2_data5 */
> +			OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs0.hsusb2_data6 */
> +			OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* mcspi2_cs1.hsusb2_data3 */
> +			OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4)		/* i2c2_scl.gpio_168 */
> +			OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4)		/* i2c2_sda.gpio_183 */
> +		>;
> +	};
>  };
>  
>  &i2c1 {
> @@ -177,6 +213,14 @@
>  	power = <50>;
>  };
>  
> +&usbhshost {
> +	port2-mode = "ehci-phy";
> +};
> +
> +&usbhsehci {
> +	phys = <0 &hsusb2_phy>;
> +};
> +
>  &uart2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart2_pins>;
> diff --git a/arch/arm/boot/dts/omap3-overo-storm.dtsi b/arch/arm/boot/dts/omap3-overo-storm.dtsi
> index c235ae8..6cb418b 100644
> --- a/arch/arm/boot/dts/omap3-overo-storm.dtsi
> +++ b/arch/arm/boot/dts/omap3-overo-storm.dtsi
> @@ -10,6 +10,22 @@
>  #include "omap3-overo-base.dtsi"
>  
>  &omap3_pmx_core2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +			&hsusb2_2_pins
> +	>;
> +
> +	hsusb2_2_pins: pinmux_hsusb2_2_pins {
> +		pinctrl-single,pins = <
> +			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
> +			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
> +			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
> +			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
> +			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
> +			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */

If you don't use the OMAP3x30_CORE2_IOPAD() macro then these definitions can fit in omap3-overo-base.dtsi.
The offsets will be taken care of if you place them within &omap3_pmx_core2 {} . e.g.

+                       0x50 (PIN_OUTPUT | MUX_MODE3)           /* etk_d10.hsusb2_clk */
+                       0x52 (PIN_OUTPUT | MUX_MODE3)           /* etk_d11.hsusb2_stp */
+                       0x54 (PIN_INPUT_PULLDOWN | MUX_MODE3)   /* etk_d12.hsusb2_dir */
+                       0x56 (PIN_INPUT_PULLDOWN | MUX_MODE3)   /* etk_d13.hsusb2_nxt */
+                       0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3)   /* etk_d14.hsusb2_data0 */
+                       0x5a (PIN_INPUT_PULLDOWN | MUX_MODE3)   /* etk_d15.hsusb2_data1 */

Do you think this is better?

cheers,
-roger


> +		>;
> +	};
> +
>  	w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
>  		pinctrl-single,pins = <
>  			OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 */
> diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
> index 95c59b2..c37b130 100644
> --- a/arch/arm/boot/dts/omap3-overo.dtsi
> +++ b/arch/arm/boot/dts/omap3-overo.dtsi
> @@ -10,6 +10,22 @@
>  #include "omap3-overo-base.dtsi"
>  
>  &omap3_pmx_core2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <
> +			&hsusb2_2_pins
> +	>;
> +
> +	hsusb2_2_pins: pinmux_hsusb2_2_pins {
> +		pinctrl-single,pins = <
> +			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)		/* etk_d10.hsusb2_clk */
> +			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)		/* etk_d11.hsusb2_stp */
> +			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d12.hsusb2_dir */
> +			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d13.hsusb2_nxt */
> +			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d14.hsusb2_data0 */
> +			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)	/* etk_d15.hsusb2_data1 */
> +		>;
> +	};
> +
>  	w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins {
>  		pinctrl-single,pins = <
>  			OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4)		/* etk_d2.gpio_16 */
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux