[PATCH v5 5/5] mmc: add support for HS400 mode of eMMC5.0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This patch adds HS400 mode support for eMMC5.0 device.
HS400 mode is high speed DDR interface timing from HS200.
Clock frequency is up to 200MHz and only 8-bit bus width is
supported. In addition, tuning process of HS200 is required
to synchronize the command response on the CMD line because
CMD input timing for HS400 mode is the same as HS200 mode.

Signed-off-by: Seungwon Jeon <tgih.jun@xxxxxxxxxxx>
Tested-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
Acked-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
---
 drivers/mmc/core/bus.c     |    1 +
 drivers/mmc/core/debugfs.c |    3 +
 drivers/mmc/core/mmc.c     |   98 +++++++++++++++++++++++++++++++++++++++++--
 include/linux/mmc/card.h   |    1 +
 include/linux/mmc/host.h   |   14 ++++++
 include/linux/mmc/mmc.h    |    7 +++-
 6 files changed, 118 insertions(+), 6 deletions(-)

diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c
index f37e9d6..d2dbf02 100644
--- a/drivers/mmc/core/bus.c
+++ b/drivers/mmc/core/bus.c
@@ -349,6 +349,7 @@ int mmc_add_card(struct mmc_card *card)
 			mmc_hostname(card->host),
 			mmc_card_uhs(card) ? "ultra high speed " :
 			(mmc_card_hs(card) ? "high speed " : ""),
+			mmc_card_hs400(card) ? "HS400 " :
 			(mmc_card_hs200(card) ? "HS200 " : ""),
 			mmc_card_ddr52(card) ? "DDR " : "",
 			uhs_bus_speed_mode, type, card->rca);
diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
index 1f730db..91eb162 100644
--- a/drivers/mmc/core/debugfs.c
+++ b/drivers/mmc/core/debugfs.c
@@ -141,6 +141,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
 	case MMC_TIMING_MMC_HS200:
 		str = "mmc HS200";
 		break;
+	case MMC_TIMING_MMC_HS400:
+		str = "mmc HS400";
+		break;
 	default:
 		str = "invalid";
 		break;
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index 7e9b424..c12e247 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -240,7 +240,7 @@ static int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
 static void mmc_select_card_type(struct mmc_card *card)
 {
 	struct mmc_host *host = card->host;
-	u8 card_type = card->ext_csd.raw_card_type & EXT_CSD_CARD_TYPE_MASK;
+	u8 card_type = card->ext_csd.raw_card_type;
 	u32 caps = host->caps, caps2 = host->caps2;
 	unsigned int hs_max_dtr = 0, hs200_max_dtr = 0;
 	unsigned int avail_type = 0;
@@ -281,6 +281,18 @@ static void mmc_select_card_type(struct mmc_card *card)
 		avail_type |= EXT_CSD_CARD_TYPE_HS200_1_2V;
 	}
 
+	if (caps2 & MMC_CAP2_HS400_1_8V &&
+	    card_type & EXT_CSD_CARD_TYPE_HS400_1_8V) {
+		hs200_max_dtr = MMC_HS200_MAX_DTR;
+		avail_type |= EXT_CSD_CARD_TYPE_HS400_1_8V;
+	}
+
+	if (caps2 & MMC_CAP2_HS400_1_2V &&
+	    card_type & EXT_CSD_CARD_TYPE_HS400_1_2V) {
+		hs200_max_dtr = MMC_HS200_MAX_DTR;
+		avail_type |= EXT_CSD_CARD_TYPE_HS400_1_2V;
+	}
+
 	card->ext_csd.hs_max_dtr = hs_max_dtr;
 	card->ext_csd.hs200_max_dtr = hs200_max_dtr;
 	card->mmc_avail_type = avail_type;
@@ -499,6 +511,8 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
 			ext_csd[EXT_CSD_PWR_CL_DDR_52_195];
 		card->ext_csd.raw_pwr_cl_ddr_52_360 =
 			ext_csd[EXT_CSD_PWR_CL_DDR_52_360];
+		card->ext_csd.raw_pwr_cl_ddr_200_360 =
+			ext_csd[EXT_CSD_PWR_CL_DDR_200_360];
 	}
 
 	if (card->ext_csd.rev >= 5) {
@@ -665,7 +679,10 @@ static int mmc_compare_ext_csds(struct mmc_card *card, unsigned bus_width)
 		(card->ext_csd.raw_pwr_cl_ddr_52_195 ==
 			bw_ext_csd[EXT_CSD_PWR_CL_DDR_52_195]) &&
 		(card->ext_csd.raw_pwr_cl_ddr_52_360 ==
-			bw_ext_csd[EXT_CSD_PWR_CL_DDR_52_360]));
+			bw_ext_csd[EXT_CSD_PWR_CL_DDR_52_360]) &&
+		(card->ext_csd.raw_pwr_cl_ddr_200_360 ==
+			bw_ext_csd[EXT_CSD_PWR_CL_DDR_200_360]));
+
 	if (err)
 		err = -EINVAL;
 
@@ -776,7 +793,9 @@ static int __mmc_select_powerclass(struct mmc_card *card,
 				ext_csd->raw_pwr_cl_52_360 :
 				ext_csd->raw_pwr_cl_ddr_52_360;
 		else if (host->ios.clock <= MMC_HS200_MAX_DTR)
-			pwrclass_val = ext_csd->raw_pwr_cl_200_360;
+			pwrclass_val = (bus_width == EXT_CSD_DDR_BUS_WIDTH_8) ?
+				ext_csd->raw_pwr_cl_ddr_200_360 :
+				ext_csd->raw_pwr_cl_200_360;
 		break;
 	default:
 		pr_warning("%s: Voltage range not supported "
@@ -840,7 +859,8 @@ static void mmc_set_bus_speed(struct mmc_card *card)
 {
 	unsigned int max_dtr = (unsigned int)-1;
 
-	if (mmc_card_hs200(card) && max_dtr > card->ext_csd.hs200_max_dtr)
+	if ((mmc_card_hs200(card) || mmc_card_hs400(card)) &&
+	     max_dtr > card->ext_csd.hs200_max_dtr)
 		max_dtr = card->ext_csd.hs200_max_dtr;
 	else if (mmc_card_hs(card) && max_dtr > card->ext_csd.hs_max_dtr)
 		max_dtr = card->ext_csd.hs_max_dtr;
@@ -993,6 +1013,61 @@ static int mmc_select_hs_ddr(struct mmc_card *card)
 	return err;
 }
 
+static int mmc_select_hs400(struct mmc_card *card)
+{
+	struct mmc_host *host = card->host;
+	int err = 0;
+
+	/*
+	 * HS400 mode requires 8-bit bus width
+	 */
+	if (!(card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS400 &&
+	      host->ios.bus_width == MMC_BUS_WIDTH_8))
+		return 0;
+
+	/*
+	 * Before switching to dual data rate operation for HS400,
+	 * it is required to convert from HS200 mode to HS mode.
+	 */
+	mmc_set_timing(card->host, MMC_TIMING_MMC_HS);
+	mmc_set_bus_speed(card);
+
+	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+			   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS,
+			   card->ext_csd.generic_cmd6_time,
+			   true, true, true);
+	if (err) {
+		pr_warn("%s: switch to high-speed from hs200 failed, err:%d\n",
+			mmc_hostname(host), err);
+		return err;
+	}
+
+	err = mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+			 EXT_CSD_BUS_WIDTH,
+			 EXT_CSD_DDR_BUS_WIDTH_8,
+			 card->ext_csd.generic_cmd6_time);
+	if (err) {
+		pr_warn("%s: switch to bus width for hs400 failed, err:%d\n",
+			mmc_hostname(host), err);
+		return err;
+	}
+
+	err = __mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
+			   EXT_CSD_HS_TIMING, EXT_CSD_TIMING_HS400,
+			   card->ext_csd.generic_cmd6_time,
+			   true, true, true);
+	if (err) {
+		pr_warn("%s: switch to hs400 failed, err:%d\n",
+			 mmc_hostname(host), err);
+		return err;
+	}
+
+	mmc_set_timing(host, MMC_TIMING_MMC_HS400);
+	mmc_set_bus_speed(card);
+
+	return 0;
+}
+
 /*
  * For device supporting HS200 mode, the following sequence
  * should be done before executing the tuning process.
@@ -1070,13 +1145,22 @@ bus_speed:
 
 /*
  * Execute tuning sequence to seek the proper bus operating
- * conditions for HS200, which sends CMD21 to the device.
+ * conditions for HS200 and HS400, which sends CMD21 to the device.
  */
 static int mmc_hs200_tuning(struct mmc_card *card)
 {
 	struct mmc_host *host = card->host;
 	int err = 0;
 
+	/*
+	 * Timing should be adjusted to the HS400 target
+	 * operation frequency for tuning process
+	 */
+	if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS400 &&
+	    host->ios.bus_width == MMC_BUS_WIDTH_8)
+		if (host->ops->prepare_hs400_tuning)
+			host->ops->prepare_hs400_tuning(host, &host->ios);
+
 	if (host->ops->execute_tuning) {
 		mmc_host_clk_hold(host);
 		err = host->ops->execute_tuning(host,
@@ -1304,6 +1388,10 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr,
 		err = mmc_hs200_tuning(card);
 		if (err)
 			goto err;
+
+		err = mmc_select_hs400(card);
+		if (err)
+			goto err;
 	} else if (mmc_card_hs(card)) {
 		/* Select the desired bus width optionally */
 		err = mmc_select_bus_width(card);
diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index c422349..e68bbeb 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -110,6 +110,7 @@ struct mmc_ext_csd {
 	u8			raw_pwr_cl_200_360;	/* 237 */
 	u8			raw_pwr_cl_ddr_52_195;	/* 238 */
 	u8			raw_pwr_cl_ddr_52_360;	/* 239 */
+	u8			raw_pwr_cl_ddr_200_360;	/* 253 */
 	u8			raw_bkops_status;	/* 246 */
 	u8			raw_sectors[4];		/* 212 - 4 bytes */
 
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 1ee3c10..1a3ced2 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -61,6 +61,7 @@ struct mmc_ios {
 #define MMC_TIMING_UHS_DDR50	7
 #define MMC_TIMING_MMC_DDR52	8
 #define MMC_TIMING_MMC_HS200	9
+#define MMC_TIMING_MMC_HS400	10
 
 	unsigned char	signal_voltage;		/* signalling voltage (1.8V or 3.3V) */
 
@@ -132,6 +133,9 @@ struct mmc_host_ops {
 
 	/* The tuning command opcode value is different for SD and eMMC cards */
 	int	(*execute_tuning)(struct mmc_host *host, u32 opcode);
+
+	/* Prepare HS400 target operating frequency depending host driver */
+	int	(*prepare_hs400_tuning)(struct mmc_host *host, struct mmc_ios *ios);
 	int	(*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
 	void	(*hw_reset)(struct mmc_host *host);
 	void	(*card_event)(struct mmc_host *host);
@@ -274,6 +278,10 @@ struct mmc_host {
 #define MMC_CAP2_PACKED_CMD	(MMC_CAP2_PACKED_RD | \
 				 MMC_CAP2_PACKED_WR)
 #define MMC_CAP2_NO_PRESCAN_POWERUP (1 << 14)	/* Don't power up before scan */
+#define MMC_CAP2_HS400_1_8V	(1 << 15)	/* Can support HS400 1.8V */
+#define MMC_CAP2_HS400_1_2V	(1 << 16)	/* Can support HS400 1.2V */
+#define MMC_CAP2_HS400		(MMC_CAP2_HS400_1_8V | \
+				 MMC_CAP2_HS400_1_2V)
 
 	mmc_pm_flag_t		pm_caps;	/* supported pm features */
 
@@ -493,4 +501,10 @@ static inline bool mmc_card_ddr52(struct mmc_card *card)
 {
 	return card->host->ios.timing == MMC_TIMING_MMC_DDR52;
 }
+
+static inline bool mmc_card_hs400(struct mmc_card *card)
+{
+	return card->host->ios.timing == MMC_TIMING_MMC_HS400;
+}
+
 #endif /* LINUX_MMC_HOST_H */
diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h
index f429f13..64ec963 100644
--- a/include/linux/mmc/mmc.h
+++ b/include/linux/mmc/mmc.h
@@ -325,6 +325,7 @@ struct _mmc_csd {
 #define EXT_CSD_POWER_OFF_LONG_TIME	247	/* RO */
 #define EXT_CSD_GENERIC_CMD6_TIME	248	/* RO */
 #define EXT_CSD_CACHE_SIZE		249	/* RO, 4 bytes */
+#define EXT_CSD_PWR_CL_DDR_200_360	253	/* RO */
 #define EXT_CSD_TAG_UNIT_SIZE		498	/* RO */
 #define EXT_CSD_DATA_TAG_SUPPORT	499	/* RO */
 #define EXT_CSD_MAX_PACKED_WRITES	500	/* RO */
@@ -354,7 +355,6 @@ struct _mmc_csd {
 #define EXT_CSD_CMD_SET_SECURE		(1<<1)
 #define EXT_CSD_CMD_SET_CPSECURE	(1<<2)
 
-#define EXT_CSD_CARD_TYPE_MASK	0x3F	/* Mask out reserved bits */
 #define EXT_CSD_CARD_TYPE_HS_26	(1<<0)	/* Card can run at 26MHz */
 #define EXT_CSD_CARD_TYPE_HS_52	(1<<1)	/* Card can run at 52MHz */
 #define EXT_CSD_CARD_TYPE_HS	(EXT_CSD_CARD_TYPE_HS_26 | \
@@ -370,6 +370,10 @@ struct _mmc_csd {
 						/* SDR mode @1.2V I/O */
 #define EXT_CSD_CARD_TYPE_HS200		(EXT_CSD_CARD_TYPE_HS200_1_8V | \
 					 EXT_CSD_CARD_TYPE_HS200_1_2V)
+#define EXT_CSD_CARD_TYPE_HS400_1_8V	(1<<6)	/* Card can run at 200MHz DDR, 1.8V */
+#define EXT_CSD_CARD_TYPE_HS400_1_2V	(1<<7)	/* Card can run at 200MHz DDR, 1.2V */
+#define EXT_CSD_CARD_TYPE_HS400		(EXT_CSD_CARD_TYPE_HS400_1_8V | \
+					 EXT_CSD_CARD_TYPE_HS400_1_2V)
 
 #define EXT_CSD_BUS_WIDTH_1	0	/* Card is in 1 bit mode */
 #define EXT_CSD_BUS_WIDTH_4	1	/* Card is in 4 bit mode */
@@ -380,6 +384,7 @@ struct _mmc_csd {
 #define EXT_CSD_TIMING_BC	0	/* Backwards compatility */
 #define EXT_CSD_TIMING_HS	1	/* High speed */
 #define EXT_CSD_TIMING_HS200	2	/* HS200 */
+#define EXT_CSD_TIMING_HS400	3	/* HS400 */
 
 #define EXT_CSD_SEC_ER_EN	BIT(0)
 #define EXT_CSD_SEC_BD_BLK_EN	BIT(2)
-- 
1.7.0.4


--
To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux USB Devel]     [Linux Media]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux