Re: Hotplug borked after suspend/resume in Linux-3.3 ?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


On Thu, Apr 19, 2012 at 2:32 AM, Martin Mokrejs <mmokrejs@xxxxxxxxxxxxxxxxxx> wrote:
> Martin Mokrejs wrote:
>>
>>
>> Jeff Garzik wrote:
>>> On 04/18/2012 01:10 PM, Martin Mokrejs wrote:
>>>> Fix: I got my 3TB disk detected by this single command:
>>>>
>>>> # echo on>   /sys/devices/pci0000:00/0000:00:1f.2/ata6/power/control
>>>> #
>>>>
>>>> This is a Dell Vostro 3550 with A09 BIOS. Same happend with 3.4-rc3 kernel.
>>>>
>>>> I can do some more testing if you want me to.
>>>> Best,
>>>> Martin
>>>
>>>
>>> Can you test this one-line patch from Lin Ming?  Hopefully there is zero sysfs twiddling required with this one...
>>>
>>> --- a/drivers/ata/libata-transport.c
>>> +++ b/drivers/ata/libata-transport.c
>>> @@ -294,6 +294,7 @@ int ata_tport_add(struct device *parent,
>>>      device_enable_async_suspend(dev);
>>>      pm_runtime_set_active(dev);
>>>      pm_runtime_enable(dev);
>>> +    pm_runtime_forbid(dev);
>>>
>>>      transport_add_device(dev);
>>>      transport_configure_device(dev);
>
>
> There is one more minor issue. I cannot get my disk re-dectected at 3Gbps. Here is when I plugged it in
> for the very first time after bootup (plain 3.4-rc3 with the above one-line fix):

I did bisect and found that this is a really old regression introduced
in 2.6.37-rc1 with below commit.

commit d9027470b88631d0956ac37cdadfdeb9cdcf2c99
Author: Gwendal Grignou <gwendal@xxxxxxxxxx>
Date:   Tue May 25 12:31:38 2010 -0700

    [libata] Add ATA transport class

    This is a scheleton for libata transport class.
    All information is read only, exporting information from libata:
    - ata_port class: one per ATA port
    - ata_link class: one per ATA port or 15 for SATA Port Multiplier
    - ata_device class: up to 2 for PATA link, usually one for SATA.

    Signed-off-by: Gwendal Grignou <gwendal@xxxxxxxxxx>
    Reviewed-by: Grant Grundler <grundler@xxxxxxxxxx>
    Signed-off-by: Jeff Garzik <jgarzik@xxxxxxxxxx>


Here is the patch to fix it.

Gwendal and Grant,

Would you help to review it?


>From f696daec7ff63e9b3697e8f7ef8f985152667965 Mon Sep 17 00:00:00 2001
From: Lin Ming <ming.m.lin@xxxxxxxxx>
Date: Thu, 19 Apr 2012 15:45:51 +0800
Subject: [PATCH] libata: clear error mask of old error history

The old error history was cleared in ata_ering_clear().
It only sets ATA_EFLAG_OLD_ER eflags, but the err_mask was not cleared.
So ata_ering_map() still iterates the old error history.

This causes problem, for example, wrong probe trials count were returned in
ata_eh_schedule_probe(), which in turn causes SATA link speed to be slowed down
to 1.5Gbps.

Reported-by: Martin Mokrejs <mmokrejs@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Lin Ming <ming.m.lin@xxxxxxxxx>
---
 drivers/ata/libata-eh.c |    3 ++-
 1 files changed, 2 insertions(+), 1 deletions(-)

diff --git a/drivers/ata/libata-eh.c b/drivers/ata/libata-eh.c
index c61316e..4c6f49b 100644
--- a/drivers/ata/libata-eh.c
+++ b/drivers/ata/libata-eh.c
@@ -419,9 +419,10 @@ int ata_ering_map(struct ata_ering *ering,
 	return rc;
 }
 
-int ata_ering_clear_cb(struct ata_ering_entry *ent, void *void_arg)
+static int ata_ering_clear_cb(struct ata_ering_entry *ent, void *void_arg)
 {
 	ent->eflags |= ATA_EFLAG_OLD_ER;
+	ent->err_mask = 0;
 	return 0;
 }
 
-- 
1.7.2.5



>
> [  146.876489] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4050000 action 0xe frozen
> [  146.876499] ata6: irq_stat 0x00400040, connection status changed
> [  146.876508] ata6: SError: { PHYRdyChg CommWake DevExch }
> [  146.876527] ata6: hard resetting link
> [  147.619956] ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
> [  147.869349] ata6.00: ATA-8: ST3000DM001-9YN166, CC4C, max UDMA/133
> [  147.869360] ata6.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> [  147.870126] ata6.00: configured for UDMA/133
> [  147.870131] ata6: EH complete
> [  147.870220] scsi 5:0:0:0: Direct-Access     ATA      ST3000DM001-9YN1 CC4C PQ: 0 ANSI: 5
> [  147.870391] sd 5:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
> [  147.870393] sd 5:0:0:0: [sdc] 4096-byte physical blocks
> [  147.870396] sd 5:0:0:0: Attached scsi generic sg3 type 0
> [  147.870434] sd 5:0:0:0: [sdc] Write Protect is off
> [  147.870436] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> [  147.870460] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [  147.904848]  sdc: sdc1
> [  147.905196] sd 5:0:0:0: [sdc] Attached SCSI disk
>
>
> Here is what happens on re-plug of the device. It is a 3.5" drive and the line
> [  617.838013] ata6: hard resetting link
> happens too early. I can hear the drive is still spinning up, it can't be ready yet.
> I think the delay should be increased.
>
>
> [  617.837966] ata6: exception Emask 0x10 SAct 0x0 SErr 0x4050002 action 0xe frozen
> [  617.837976] ata6: irq_stat 0x00400040, connection status changed
> [  617.837984] ata6: SError: { RecovComm PHYRdyChg CommWake DevExch }
> [  617.838004] ata6: limiting SATA link speed to 1.5 Gbps
> [  617.838013] ata6: hard resetting link
> [  623.610941] ata6: link is slow to respond, please be patient (ready=0)
> [  627.864604] ata6: COMRESET failed (errno=-16)
> [  627.864615] ata6: hard resetting link
> [  629.931538] ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
> [  629.932355] ata6.00: ATA-8: ST3000DM001-9YN166, CC4C, max UDMA/133
> [  629.932365] ata6.00: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
> [  629.933170] ata6.00: configured for UDMA/133
> [  629.951629] ata6: EH complete
> [  629.951700] scsi 5:0:0:0: Direct-Access     ATA      ST3000DM001-9YN1 CC4C PQ: 0 ANSI: 5
> [  629.951816] sd 5:0:0:0: [sdc] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
> [  629.951819] sd 5:0:0:0: [sdc] 4096-byte physical blocks
> [  629.951842] sd 5:0:0:0: Attached scsi generic sg3 type 0
> [  629.951875] sd 5:0:0:0: [sdc] Write Protect is off
> [  629.951877] sd 5:0:0:0: [sdc] Mode Sense: 00 3a 00 00
> [  629.951901] sd 5:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
> [  629.995970]  sdc: sdc1
> [  629.996359] sd 5:0:0:0: [sdc] Attached SCSI disk
>
>
> Martin


--
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Linux Filesystems]     [Linux SCSI]     [Linux RAID]     [Git]     [Kernel Newbies]     [Linux Newbie]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Photo]     [Yosemite]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux