[Patch v1 3/4] iio: imu: Enable checking of presence of device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Added logic to check presence of MPU6050 before continuing. Currently
only i2c writes are used in the initialzation path, which don't return
any error, if some i2c device responds. In this case it continues to
create iio devices, which don't work.
This can be reproduced in a PC like platform, where ACPI definition
of this defines multiple i2c addresses. We need to check for an valid
i2c address by checking some id before continuing.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@xxxxxxxxxxxxxxx>
---
 drivers/iio/imu/inv_mpu6050/inv_mpu_core.c | 27 +++++++++++++++++++++++++++
 drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h  |  5 +++++
 2 files changed, 32 insertions(+)

diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index 744eba4..200163d 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -54,6 +54,7 @@ static const struct inv_mpu6050_reg_map reg_set_6050 = {
 	.pwr_mgmt_1             = INV_MPU6050_REG_PWR_MGMT_1,
 	.pwr_mgmt_2             = INV_MPU6050_REG_PWR_MGMT_2,
 	.int_pin_cfg		= INV_MPU6050_REG_INT_PIN_CFG,
+	.who_am_i		= INV_MPU6050_REG_WHOAMI,
 };
 
 static const struct inv_mpu6050_chip_config chip_config_6050 = {
@@ -74,6 +75,12 @@ static const struct inv_mpu6050_hw hw_info[INV_NUM_PARTS] = {
 	},
 };
 
+static const u16 inv_mpu_unique_ids[] = {
+	INV_MPU60X0_UNIQUE_ID,
+	INV_MPU6500_UNIQUE_ID,
+	0x0000,
+};
+
 int inv_mpu6050_write_reg(struct inv_mpu6050_state *st, int reg, u8 d)
 {
 	return i2c_smbus_write_i2c_block_data(st->client, reg, 1, &d);
@@ -630,6 +637,8 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st,
 		const struct i2c_device_id *id)
 {
 	int result;
+	bool matched = false;
+	int i = 0;
 
 	st->chip_type = INV_MPU6050;
 	st->hw  = &hw_info[st->chip_type];
@@ -641,6 +650,24 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st,
 	if (result)
 		return result;
 	msleep(INV_MPU6050_POWER_UP_TIME);
+
+	result = i2c_smbus_read_byte_data(st->client, st->reg->who_am_i);
+	if (result < 0) {
+		dev_err(&st->client->dev, "Error reading WhoAmI\n");
+		return result;
+	}
+
+	while (inv_mpu_unique_ids[i] != 0x0000) {
+		if (inv_mpu_unique_ids[i++] == result)
+			matched = true;
+	}
+
+	if (!matched) {
+		dev_err(&st->client->dev, "Not a valid MPU6XXX device %x\n",
+								result);
+		return -ENOSYS;
+	}
+
 	/* toggle power state. After reset, the sleep bit could be on
 		or off depending on the OTP settings. Toggling power would
 		make it in a definite state as well as making the hardware
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
index 591ac2e..41196c5 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
@@ -55,6 +55,7 @@ struct inv_mpu6050_reg_map {
 	u8 pwr_mgmt_1;
 	u8 pwr_mgmt_2;
 	u8 int_pin_cfg;
+	u8 who_am_i;
 };
 
 /*device enum */
@@ -190,6 +191,10 @@ struct inv_mpu6050_state {
 #define INV_MPU6050_REG_INT_PIN_CFG		0x37
 #define INV_MPU6050_BIT_BYPASS_EN		0x2
 
+#define INV_MPU6050_REG_WHOAMI			0x75
+#define INV_MPU6500_UNIQUE_ID			0x70
+#define INV_MPU60X0_UNIQUE_ID			0x68
+
 /* scan element definition */
 enum inv_mpu6050_scan {
 	INV_MPU6050_SCAN_ACCL_X,
-- 
1.7.11.7

--
To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux IBM ACPI]     [Linux Power Management]     [Linux Kernel]     [Linux Laptop]     [Kernel Newbies]     [Share Photos]     [Security]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux