RE: Andrew, United States, kernel 3.0.0-12-generic

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



If you mean physically on the board, No. What if I disable the serial port
in the BIOS?

-----Original Message-----
From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx] 
Sent: Friday, June 22, 2012 5:42 PM
To: Andrew Merczynski-Hait; 'Antonio Olivares'
Cc: 'Linmodems'; 'Marvin Stodolsky'
Subject: Re: Andrew, United States, kernel 3.0.0-12-generic

Dear Andrew,

There is an IRQ conflict between the serial driver and the Intel 537EP
driver. They both interrupt at PCI INT A -> GSI 22 (level, low) -> IRQ 22.
Can you look attentively at the specs of your modem board to watch out for a
possible jumper which would select another IRQ ? This can explain the error
returned on AT+FIP and the observed NO CARRIER.

Dear Antonio,

Do you know a way to prevent the serial driver from acting ? It conflicts
with the Intel 537EP driver.

Dear Andrew, Antonio,

A possible solution is to either invalidate the serial driver or change the
Intel 537EP modem IRQ.

Philippe Vouters (Fontainebleau/France)
URL: http://vouters.dyndns.org/
SIP: sip:Vouters@xxxxxxxxxxxxxxxx

Le 22/06/2012 23:17, Andrew Merczynski-Hait a écrit :
> andrew@ubuntu-11:~$ dmesg | grep IRQ
> [    0.000000] ACPI: IRQ0 used by override.
> [    0.000000] ACPI: IRQ2 used by override.
> [    0.000000] ACPI: IRQ9 used by override.
> [    0.000000] NR_IRQS:2304 nr_irqs:712 16
> [    0.264046] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12
> 15)
> [    0.264357] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 7 9 10 11 12
> 15)
> [    0.264667] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12
> 15)
> [    0.264975] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12
> 15)
> [    0.265283] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12
> 15)
> [    0.265591] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12
> 15)
> [    0.265898] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12
> 15)
> [    0.266207] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12
> 15)
> [    0.267074] PCI: Using ACPI for IRQ routing
> [    0.267438] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
> [    0.464138] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
> [    0.640333] serial 0000:01:01.0: PCI INT A -> GSI 22 (level, low) ->
IRQ
> 22
> [    0.651008] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) ->
> IRQ 18
> [    0.657120] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) ->
> IRQ 23
> [    0.728663] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) ->
> IRQ 16
> [    0.729019] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) ->
> IRQ 19
> [    0.729343] uhci_hcd 0000:00:1d.3: PCI INT A -> GSI 16 (level, low) ->
> IRQ 16
> [    1.422812] e100 0000:01:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ
20
> [    1.473846] firewire_ohci 0000:01:00.0: PCI INT A -> GSI 21 (level,
low)
> -> IRQ 21
> [   19.275485] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
> [   20.860201] CA0106 0000:01:02.0: PCI INT A -> GSI 17 (level, low) ->
IRQ
> 17
> [   21.570776] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) ->
> IRQ 17
> [  129.505453] pci 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> 
> IRQ 22
>
> -----Original Message-----
> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
> Sent: Friday, June 22, 2012 5:13 PM
> To: Andrew Merczynski-Hait
> Cc: 'Linmodems'; 'Antonio Olivares'; 'Marvin Stodolsky'
> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>
> Andrew,
>
> Now what does happen if you do:
> $ dmesg | grep IRQ ?
>
> Philippe Vouters (Fontainebleau/France)
> URL: http://vouters.dyndns.org/
> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>
> Le 22/06/2012 22:24, Andrew Merczynski-Hait a écrit :
>>              CPU0
>>     0:         49   IO-APIC-edge      timer
>>     1:        145   IO-APIC-edge      i8042
>>     4:          4   IO-APIC-edge
>>     6:          3   IO-APIC-edge      floppy
>>     7:          0   IO-APIC-edge      parport0
>>     8:          1   IO-APIC-edge      rtc0
>>     9:          0   IO-APIC-fasteoi   acpi
>>    14:          0   IO-APIC-edge      ata_piix
>>    15:        186   IO-APIC-edge      ata_piix
>>    16:        828   IO-APIC-fasteoi   uhci_hcd:usb2, uhci_hcd:usb4, i915
>>    17:        306   IO-APIC-fasteoi   snd_ca0106, Intel ICH5
>>    19:        692   IO-APIC-fasteoi   uhci_hcd:usb3
>>    20:        135   IO-APIC-fasteoi   eth0
>>    21:          4   IO-APIC-fasteoi   firewire_ohci
>>    23:      23981   IO-APIC-fasteoi   ehci_hcd:usb1
>> NMI:          0   Non-maskable interrupts
>> LOC:      14182   Local timer interrupts
>> SPU:          0   Spurious interrupts
>> PMI:          0   Performance monitoring interrupts
>> IWI:          0   IRQ work interrupts
>> RES:          0   Rescheduling interrupts
>> CAL:          0   Function call interrupts
>> TLB:          0   TLB shootdowns
>> TRM:          0   Thermal event interrupts
>> THR:          0   Threshold APIC interrupts
>> MCE:          0   Machine check exceptions
>> MCP:          1   Machine check polls
>> ERR:          0
>> MIS:          0
>>
>>
>> Thanks,
>> Andrew
>> -----Original Message-----
>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>> Sent: Friday, June 22, 2012 4:14 PM
>> To: Andrew Merczynski-Hait
>> Cc: 'Linmodems'; 'Antonio Olivares'; 'Marvin Stodolsky'
>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>
>> Andrew,
>>
>> The modem answers with:
>>
>> efax: 18:09 waiting 120.0 s
>> efax: 19:40 .532 [<CR><LF>NO CARRIER<CR><LF>]
>> efax: 19:40 response "NO CARRIER"
>> efax: 19:40 Error: unable to answer call
>> efax: 19:40 command  "Q0V1"
>> efax: 19:40 waiting 2.0 s
>>
>> Can you send us the following:
>> $ sudo cat /proc/interrupts
>> ???
>> Thank you in advance
>>
>> Philippe Vouters (Fontainebleau/France)
>> URL: http://vouters.dyndns.org/
>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>
>> Le 22/06/2012 21:22, Andrew Merczynski-Hait a écrit :
>>> Yes, if I hook up a phone to it I get a dial tone. My modem has two 
>>> physical ports on the back, so now I switched where the phone line 
>>> goes in to just to be sure. I still get the same error though. If I 
>>> listen to the phone while running it, I can hear the line ring 
>>> twice, and
>> then stop.
>>> If I don't terminate after that error after a while I get this:
>>>
>>> efax: 18:09 command  "+FNR=1,1,1,0"
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .132 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "+FLO=1"
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .304 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "+FBO=0"
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .472 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "+FCR=1"
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .644 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "+FIS?"
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .692 [<CR><LF>1,5,0,2,0,0,0,0<CR><LF>]
>>> efax: 18:09 .712 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "+FLI="                    ""
>>> efax: 18:09 waiting 5.0 s
>>> efax: 18:09 .784 [<CR><LF>OK<CR><LF>]
>>> efax: 18:09 response "OK"
>>> efax: 18:09 command  "A"
>>> efax: 18:09 waiting 120.0 s
>>> efax: 19:40 .532 [<CR><LF>NO CARRIER<CR><LF>]
>>> efax: 19:40 response "NO CARRIER"
>>> efax: 19:40 Error: unable to answer call
>>> efax: 19:40 command  "Q0V1"
>>> efax: 19:40 waiting 2.0 s
>>> efax: 19:40 .712 [<CR><LF>OK<CR><LF>]
>>> efax: 19:40 response "OK"
>>> efax: 19:40 command  "H"
>>> efax: 19:40 waiting 5.0 s
>>> efax: 19:41 .572 [<CR><LF>OK<CR><LF>]
>>> efax: 19:41 response "OK"
>>> efax: 19:41 done, returning 3 (invalid modem response
>>>
>>>
>>>
>>> -----Original Message-----
>>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>>> Sent: Friday, June 22, 2012 3:06 PM
>>> To: Andrew Merczynski-Hait
>>> Cc: 'Linmodems'; 'Antonio Olivares'; Marvin Stodolsky
>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>
>>> Andrew,
>>>
>>> With efax, you get this:
>>> efax: 47:42 command "Q0V1"
>>> efax: 47:42 waiting 2.0 s
>>> efax: 47:43 .072 [<CR><LF>NO CARRIER<CR><LF>]
>>> efax: 47:43 response "NO CARRIER"
>>> efax: 47:43 waiting 2.0 s
>>> efax: 47:45 command "Q0V1"
>>> efax: 47:45 waiting 2.0 s
>>> efax: 47:45 .252 [<CR><LF>OK<CR><LF>]
>>> efax: 47:45 response "OK"
>>>
>>> Are you sure your537EP modem is physically connected to a phone line ?
>>>
>>> Marv,
>>>
>>> I need your help for Ubuntu. Unlike Fedora, there is no
> /var/log/messages.
>>> Where does syslog logs on Ubuntu ????
>>>
>>> Philippe Vouters (Fontainebleau/France)
>>> URL: http://vouters.dyndns.org/
>>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>>
>>> Le 22/06/2012 20:49, Andrew Merczynski-Hait a écrit :
>>>> andrew@ubuntu-11:~$ efax -i M2L3 -vewinchmart
>>>> efax: Fri Jun 22 14:46:09 2012 efax v 0.9a-001114 Copyright 1999 Ed 
>>>> Casas
>>>> efax: Fri Jun 22 14:46:09 2012 efax v 0.9a-001114 Copyright 1999 Ed 
>>>> Casas
>>>> efax: 46:09 compiled Jun 21 2006 05:59:09
>>>> efax: 46:09 argv[0]=efax
>>>> efax: 46:09 argv[1]=-i
>>>> efax: 46:09 argv[2]=M2L3
>>>> efax: 46:09 argv[3]=-vewinchmart
>>>> efax: 46:11 opened /dev/modem
>>>> efax: 46:11 command  "Q0V1"
>>>> efax: 46:11 waiting 2.0 s
>>>> efax: 46:15 waiting 2.0 s
>>>> efax: 46:15 .120 [ATQ0V1<CR><CR><LF>]
>>>> efax: 46:15 .180 [OK<CR><LF>]
>>>> efax: 46:15 response "OK"
>>>> efax: 46:15 waiting 2.0 s
>>>> efax: 46:17 command  "Q0V1"
>>>> efax: 46:17 waiting 2.0 s
>>>> efax: 46:17 .300 [ATQ0V1<CR><CR><LF>]
>>>> efax: 46:17 .360 [OK<CR><LF>]
>>>> efax: 46:17 response "OK"
>>>> efax: 46:17 command  "M2L3"
>>>> efax: 46:17 waiting 5.0 s
>>>> efax: 46:17 .480 [ATM2L3<CR><CR><LF>]
>>>> efax: 46:17 .540 [OK<CR><LF>]
>>>> efax: 46:17 response "OK"
>>>> efax: 46:17 command  "E0"
>>>> efax: 46:17 waiting 5.0 s
>>>> efax: 46:17 .660 [ATE0<CR><CR><LF>]
>>>> efax: 46:17 .712 [OK<CR><LF>]
>>>> efax: 46:17 response "OK"
>>>> efax: 46:17 command  "I3"
>>>> efax: 46:17 waiting 5.0 s
>>>> efax: 46:17 .860 [<CR><LF>537EP <CR><LF>]
>>>> efax: 46:17 .880 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:17 response "OK"
>>>> efax: 46:17 command  "+FCLASS=?"
>>>> efax: 46:17 waiting 5.0 s
>>>> efax: 46:18 .032 [<CR><LF>0,1,2,2.0,8<CR><LF>]
>>>> efax: 46:18 .052 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:18 response "OK"
>>>> efax: 46:18 command  "+FCLASS=2.0"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:18 .220 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:18 response "OK"
>>>> efax: 46:18 command  "+FMI?"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:18 .372 [<CR><LF>Intel Corporation<CR><LF>]
>>>> efax: 46:18 .392 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:18 response "OK"
>>>> efax: 46:18 command  "+FMM?"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:18 .540 [<CR><LF>Intel V92 Data Fax Voice<CR><LF>]
>>>> efax: 46:18 .540 [<CR><LF>H.324 video-ready rev. 1.0<CR><LF>]
>>>> efax: 46:18 .560 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:18 response "OK"
>>>> efax: 46:18 command  "+FMR?"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:18 .712 [<CR><LF>RSA REV 4.04 <CR><LF>]
>>>> efax: 46:18 .732 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:18 response "OK"
>>>> efax: 46:18 using 537EP Intel Corporation Intel V92 Data Fax Voice 
>>>> RSA REV
>>>> 4.04 in class 2.0
>>>> efax: 46:18 command  "+FIP"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:18 .892 [<CR><LF>ERROR<CR><LF>]
>>>> efax: 46:18 response "ERROR"
>>>> efax: 46:18 Warning: wrong response after command:  +FIP THEN IT 
>>>> HANGS AND I TERMINATE IT AND GET THIS:
>>>>
>>>> ^Cefax: 46:18 command  "+FNR=1,1,1,0"
>>>> efax: 46:18 waiting 5.0 s
>>>> efax: 46:19 .060 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "+FLO=1"
>>>> efax: 46:19 waiting 5.0 s
>>>> efax: 46:19 .232 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "+FBO=0"
>>>> efax: 46:19 waiting 5.0 s
>>>> efax: 46:19 .400 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "+FCR=1"
>>>> efax: 46:19 waiting 5.0 s
>>>> efax: 46:19 .572 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "+FIS?"
>>>> efax: 46:19 waiting 5.0 s
>>>> efax: 46:19 .620 [<CR><LF>1,5,0,2,0,0,0,0<CR><LF>]
>>>> efax: 46:19 .640 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "+FLI="                    ""
>>>> efax: 46:19 waiting 5.0 s
>>>> efax: 46:19 .712 [<CR><LF>OK<CR><LF>]
>>>> efax: 46:19 response "OK"
>>>> efax: 46:19 command  "A"
>>>> efax: 46:19 waiting 120.0 s
>>>> efax: 47:42 Error: terminating on signal 2
>>>> efax: 47:42 command  "Q0V1"
>>>> efax: 47:42 waiting 2.0 s
>>>> efax: 47:43 .072 [<CR><LF>NO CARRIER<CR><LF>]
>>>> efax: 47:43 response "NO CARRIER"
>>>> efax: 47:43 waiting 2.0 s
>>>> efax: 47:45 command  "Q0V1"
>>>> efax: 47:45 waiting 2.0 s
>>>> efax: 47:45 .252 [<CR><LF>OK<CR><LF>]
>>>> efax: 47:45 response "OK"
>>>> efax: 47:45 command  "H"
>>>> efax: 47:45 waiting 5.0 s
>>>> efax: 47:46 .112 [<CR><LF>OK<CR><LF>]
>>>> efax: 47:46 response "OK"
>>>> efax: 47:46 done, returning 5 (terminated by signal)
>>>>
>>>>
>>>> There is no such file or directory /var/log/messages
>>>>
>>>> -----Original Message-----
>>>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>>>> Sent: Friday, June 22, 2012 9:41 AM
>>>> To: Andrew Merczynski-Hait; Linmodems; Antonio Olivares
>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>
>>>> Andrew,
>>>>
>>>> Can you cut and paste the full efax dialog along with $ tail -f 
>>>> /var/log/messages started in another terminal ?
>>>>
>>>> Philippe Vouters (Fontainebleau/France)
>>>> URL: http://vouters.dyndns.org/
>>>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>>>
>>>> Le 22/06/2012 02:19, Andrew Merczynski-Hait a écrit :
>>>>> Okay, using efax it seems that it sees the modem. It stops with,
>>> "Warning:
>>>>> wrong response after command: +FIP"
>>>>>
>>>>> What can I provide now to help?
>>>>>
>>>>> -----Original Message-----
>>>>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>>>>> Sent: Thursday, June 21, 2012 5:01 PM
>>>>> To: Andrew Merczynski-Hait
>>>>> Cc: 'Antonio Olivares'; 'Jacques Goldberg'; 'Marvin Stodolsky'
>>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>>
>>>>> Andrew,
>>>>>
>>>>> Can you follow the steps at
>>>>> http://vouters.dyndns.org/Intel/Intel-Readme.html ???
>>>>> It starts with testing using efax.
>>>>> Do not yet use wvdialconf unless you know what you do.
>>>>>
>>>>> Philippe Vouters (Fontainebleau/France)
>>>>> URL: http://vouters.dyndns.org/
>>>>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>>>>
>>>>> Le 21/06/2012 22:52, Andrew Merczynski-Hait a écrit :
>>>>>> andrew@ubuntu-11:~/Downloads/intel-536-537$ sudo wvdialconf 
>>>>>> [sudo] password for andrew:
>>>>>> Editing `/etc/wvdial.conf'.
>>>>>>
>>>>>> Scanning your serial ports for a modem.
>>>>>>
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 
>>>>>> baud
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 
>>>>>> baud
>>>>>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>>>> Modem Port Scan<*1>: S1   S2   S3   S4   S5   S6   S7   S8
>>>>>> Modem Port Scan<*1>: S9   S10  S11  S12  S13  S14  S15  S16
>>>>>> Modem Port Scan<*1>: S17  S18  S19  S20  S21  S22  S23  S24 Modem 
>>>>>> Port
>>>>>> Scan<*1>: S25  S26  S27  S28  S29  S30  S31
>>>>>>
>>>>>>
>>>>>> Sorry, no modem was detected!  Is it in use by another program?
>>>>>> Did you configure it properly with setserial?
>>>>>>
>>>>>> Please read the FAQ at http://alumnit.ca/wiki/?WvDial
>>>>>>
>>>>>>
>>>>>> $ dmesg | grep '537'
>>>>>> [   20.615679] Intel 537EP card found
>>>>>> [   20.615683] 537ep:softcore_init_struct: driver serial already
>>>> allocated
>>>>>> device.
>>>>>> [   20.615687] 537ep:softcore_init_struct: Unregistering serial
> driver.
>>>>>> [  268.245922] Modules linked in: Intel537(+) bnep rfcomm 
>>>>>> bluetooth ppdev
>>>>>> snd_ca0106 snd_seq_midi snd_rawmidi snd_intel8x0 snd_ac97_codec 
>>>>>> ac97_bus snd_pcm snd_seq_midi_event binfmt_misc dcdbas snd_seq 
>>>>>> snd_timer snd_seq_device snd soundcore snd_page_alloc i915 
>>>>>> parport_pc drm_kms_helper drm shpchp i2c_algo_bit video lp 
>>>>>> parport usbhid hid firewire_ohci e100 usb_storage uas 
>>>>>> firewire_core crc_itu_t floppy [last unloaded: Intel537] [ 
>>>>>> 268.246128] [<f932e693>]
>>>>>> sound_init+0xb3/0x190 [Intel537] [  268.246226] [<f932ae58>]
>>>>>> core_init_module+0x38/0x50 [Intel537] [  268.246331] [<f974a008>]
>>>>>> init_536+0x8/0x1000 [Intel537] [  268.246376] Intel 537EP card 
>>>>>> found [
>>>>> 301.827656] 537: Loaded [ 1537.609618] PM: Syncing filesystems ...
>>>>>> done.
>>>>>> [ 1537.613013] PM: Preparing system for mem sleep [ 1538.155375] 
>>>>>> firewire_ohci 0000:01:00.0: restoring config space at offset 0x4 
>>>>>> (was 0x0, writing 0xfeafd000)
>>>>>>
>>>>>>
>>>>>> -----Original Message-----
>>>>>> From: Antonio Olivares [mailto:olivares14031@xxxxxxxxx]
>>>>>> Sent: Thursday, June 21, 2012 4:44 PM
>>>>>> To: Andrew Merczynski-Hait
>>>>>> Cc: Philippe Vouters; Jacques Goldberg; Marvin Stodolsky
>>>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>>>
>>>>>> Dear Andrew,
>>>>>>
>>>>>> The driver is the same need not worry here.  After the 
>>>>>> installation is apparently successful, please do as this and send 
>>>>>> us the output of
>>>>>>
>>>>>> andrew@ubuntu-11:~/Downloads/intel-536-537$ sudo wvdialconf
>>>>>>
>>>>>> The modem driver should be loaded and the output of $ dmesg | 
>>>>>> grep
>> '537'
>>>>>> in case that wvdialconf does not find the modem port.
>>>>>>
>>>>>> Regards,
>>>>>>
>>>>>>
>>>>>> Antonio
>>>>>>
>>>>>>
>>>>>> On Thu, Jun 21, 2012 at 3:20 PM, Andrew Merczynski-Hait 
>>>>>> <andrewmh20@xxxxxxxxxx> wrote:
>>>>>>> Is that link any different than what I had earlier? The 
>>>>>>> filenames are the same. I had to have it downloaded already in 
>>>>>>> order to extract and build the driver??
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>>>>>>> Sent: Thursday, June 21, 2012 2:06 PM
>>>>>>> To: Andrew Merczynski-Hait
>>>>>>>
>>>>>>>
>>>>>>> Cc: 'Jacques Goldberg'; 'Antonio Olivares'; 'Marvin Stodolsky'
>>>>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Dear Andrew,
>>>>>>>
>>>>>>> First of all, did you download
>>>>>>> http://vouters.dyndns.org/Intel/intel-536EP-537EP_2012_05_19.tar
>>>>>>> .bz2
> ?
>>>>>>> Next I suggest you a reboot and afterwards:
>>>>>>> $ rm -rf /path/to/intel-536-537/ $ cd /path/to $ tar -jxvf 
>>>>>>> intel-536EP-537EP_2012_05_19.tar.bz2
>>>>>>> $ cd intel-536-537/
>>>>>>> $ sudo make uninstall
>>>>>>> $ make 537
>>>>>>> $ sudo make install
>>>>>>> $ dmesg | grep 537
>>>>>>> $ stty -F /dev/modem -a
>>>>>>> $ dmesg | grep 537
>>>>>>>
>>>>>>> Yours truly,
>>>>>>>
>>>>>>> Philippe Vouters (Fontainebleau/France)
>>>>>>>
>>>>>>> URL: http://vouters.dyndns.org/
>>>>>>>
>>>>>>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>>>>>>
>>>>>>> Le 21/06/2012 19:36, Andrew Merczynski-Hait a écrit :
>>>>>>>
>>>>>>> $ dmesg | grep 536
>>>>>>>
>>>>>>> [    0.000000] Inode-cache hash table entries: 65536 (order: 6,
> 262144
>>>>>>> bytes)
>>>>>>>
>>>>>>> [    0.343343] TCP bind hash table entries: 65536 (order: 7, 524288
>>>>>>> bytes)
>>>>>>>
>>>>>>> [    0.343681] TCP: Hash tables configured (established 131072 bind
>>>>>>> 65536)
>>>>>>>
>>>>>>> [    0.736536] NET: Registered protocol family 17
>>>>>>>
>>>>>>> [    2.453621] sd 2:0:0:0: [sda] Write cache: disabled, read cache:
>>>>>>> enabled, doesn't support DPO or FUA
>>>>>>>
>>>>>>> [   15.780536] EXT4-fs (sda1): mounted filesystem with ordered data
>>>> mode.
>>>>>>> Opts: (null)
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> I know you probably know what you?re doing J but I am using a 
>>>>>>> 537 modem not
>>>>>>> 536 so I also did this:
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> $ dmesg | grep 537
>>>>>>>
>>>>>>> [    0.647537] agpgart-intel 0000:00:00.0: Intel 865 Chipset
>>>>>>>
>>>>>>> [   19.664474] Intel 537EP card found
>>>>>>>
>>>>>>> [   19.664478] 537ep:softcore_init_struct: driver serial already
>>>>>>> allocated device.
>>>>>>>
>>>>>>> [   19.664482] 537ep:softcore_init_struct: Unregistering serial
>> driver.
>>>>>>>
>>>>>>> Thanks Andrew
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx]
>>>>>>> Sent: Thursday, June 21, 2012 4:17 AM
>>>>>>> To: Andrew Merczynski-Hait
>>>>>>> Cc: 'Jacques Goldberg'; 'Antonio Olivares'; 'Marvin Stodolsky'
>>>>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Hi Andrew,
>>>>>>>
>>>>>>> Can you cut'n paste and send us the following:
>>>>>>> $ dmesg | grep 536
>>>>>>> Yours truly,
>>>>>>> Philippe
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> Philippe Vouters (Fontainebleau/France)
>>>>>>>
>>>>>>> URL: http://vouters.dyndns.org/
>>>>>>>
>>>>>>> SIP: sip:Vouters@xxxxxxxxxxxxxxxx
>>>>>>>
>>>>>>> Le 21/06/2012 04:22, Andrew Merczynski-Hait a écrit :
>>>>>>>
>>>>>>> Hi all,
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> I apologize for causing an issue and I really do appreciate your
> help.
>>>>>>> I do realize you have a lot to deal with. (Incidentally, I did 
>>>>>>> make sure to put uname ?r  in quotes, I just didn?t know they 
>>>>>>> were back
>>>>>>> quotes.)
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> After copying over the autoconf.h file I seem to get a 
>>>>>>> successful build and install. However, gnome-ppp and wvdial 
>>>>>>> still cannot see that there is a modem installed. I see in the 
>>>>>>> readme that for unknown distributions the modules and utilities 
>>>>>>> will install but not the boot scripts. I presume that is 
>>>>>>> probably an issue; can it be fixed? Would it simplify things a 
>>>>>>> lot if I installed a different distro for the purpose
>>>>>> of using the modem?
>>>>>>> Thanks,
>>>>>>>
>>>>>>> Andrew
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> From: Jacques Goldberg [mailto:goldberg@xxxxxxxxxxxxxxxxxxxx]
>>>>>>> Sent: Wednesday, June 20, 2012 1:41 PM
>>>>>>> To: Andrew Merczynski-Hait
>>>>>>> Cc: 'Antonio Olivares'; 'Philippe Vouters'; 'Marvin Stodolsky'
>>>>>>> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>
>
>





[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux