Re: Andrew, United States, kernel 3.0.0-12-generic

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Andrew,

Would you mind posting posting
$ sudo wvdialconf /etc/wvdial.conf

after the apparent successful install of the driver.  If the modem
device is not found, then something else is in the way, like the
output from scanModem shows some IRQ trouble:

\begin{QUOTE}
For candidate card in slot 01:01.0, firmware information and bootup
diagnostics are:
 PCI slot       PCI ID          SubsystemID     Name
 ----------     ---------       ---------       --------------
 01:01.0        8086:1080       1028:1000       Modem: Intel Corporation
FA82537EP 56K V.92 Data/Fax Modem PCI

 Modem interrupt assignment and sharing:
 --- Bootup diagnostics for card in PCI slot 01:01.0 ----
[    0.165277] pci 0000:01:01.0: [8086:1080] type 0 class 0x000703
[    0.165296] pci 0000:01:01.0: reg 10: [mem 0xfeafe000-0xfeafefff]
[    0.165306] pci 0000:01:01.0: reg 14: [io  0xde00-0xdeff]
[    0.165366] pci 0000:01:01.0: PME# supported from D0 D3hot D3cold
[    0.165371] pci 0000:01:01.0: PME# disabled
[    0.640344] serial 0000:01:01.0: PCI INT A -> GSI 22 (level, low) -> IRQ
22
[    0.640536] 0000:01:01.0: ttyS5 at I/O 0xde08 (irq = 22) is a 16450
[    0.640645] 0000:01:01.0: ttyS6 at I/O 0xde10 (irq = 22) is a 8250
[    0.640751] 0000:01:01.0: ttyS7 at I/O 0xde18 (irq = 22) is a 16450
[    0.640860] 0000:01:01.0: ttyS8 at I/O 0xde20 (irq = 22) is a 8250
[    0.640969] 0000:01:01.0: ttyS9 at I/O 0xde28 (irq = 22) is a 8250
[    0.641611] 0000:01:01.0: ttyS16 at I/O 0xde60 (irq = 22) is a 8250

 The PCI slot 01:01.0 of the modem card may be disabled early in  a bootup
process,  but then enabled later. If modem drivers load  but the  modem is
not responsive, read DOCs/Bootup.txt about possible fixes.
 Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx  if help
is needed.
\end{QUOTE}

Please send us something so we could try to find out what is going on?

Regards,


Antonio


On Sun, Jun 17, 2012 at 9:53 PM, Andrew Merczynski-Hait
<andrewmh20@xxxxxxxxxx> wrote:
> Thank you for your help.
>
> I am not getting any errors like a kernel panic, the modem is just not
> recognized by anything. However, Scanmodem does recognize it. Nothing else
> will though.
>
> Before I posted this I did a lot of Google searching and I think I already
> tried your recommended method, and ran into problems because of the fact
> that ubuntu puts the autoconf.h file in a non-standard directory. I will try
> again and see what happens (and in case I had a slightly different file or
> something), however if it still doesn't work is there any way to fix the
> ubuntu issue, or will it be necessary to install a different distro?
>
> Thanks,
> Andrew
>
> -----Original Message-----
> From: Antonio Olivares [mailto:olivares14031@xxxxxxxxx]
> Sent: Sunday, June 17, 2012 10:25 PM
> To: Andrew Merczynski-Hait
> Cc: discuss@xxxxxxxxxxxxx; Philippe Vouters
> Subject: Re: Andrew, United States, kernel 3.0.0-12-generic
>
> Dear Andrew,
>
> You have tried the driver but what do you get?
>
> You need to provide more information.  We do not know if you got a kernel
> panic?  a kernel mismatch?
>
> I would recommend that you uninstall the driver that you have installed and
> take a different approach, ie,
>
> Download:
>
> http://vouters.dyndns.org/Intel/intel-536EP-537EP_2012_05_19.tar.bz2
>
> Carefully read the document:
>
> http://vouters.dyndns.org/Intel/Intel-Readme.html
>
> Then proceed to take steps to see if your modem may work.
>
> If you have downloaded the driver intel-536-537EP_2012_05_19.tar.bz2,
> copy it over to your Linux partition, then extract with $ tar -jxvf
> intel-536-537EP_2012_05_19.tar.bz2
> $ cd intel-536-537
> $ sudo make intel-536-537
> $ sudo make install
>
> $ sudo wvdialconf /etc/wvdial.conf
>
> to see if scanmodem finds the modem.
>
> Let us know how this goes.
>
> Regards,
>
>
> Antonio
>
> On Sun, Jun 17, 2012 at 7:42 PM, Andrew Merczynski-Hait
> <andrewmh20@xxxxxxxxxx> wrote:
>> SCANMODEM RECOGNIZES THE MODEM, BUT NOTHING ELSE SEEMS TO. I HAVE
>> TRIED A BUNCH OF MOSTLY RANDOM STUFF, AND HAVE ALREADY TRIED USING THE
>> .DEB PACKAGED 537EP DRIVERS FROM
>>
> https://sites.google.com/site/ubuntumodems/modem-driver-downloads-for-537ep.
>> THIS IS MY MODEM DATA.TXT FILE:
>>
>> Only plain text email is forwarded by the  Discuss@xxxxxxxxxxxxx List
>> Server,  as HTML can contain viruses. Use as the email Subject Line:
>>           YourName, YourCountry  kernel 3.0.0-12-generic  With this
>> Subject Line cogent experts will be alerted, and useful case names
>> left in the Archive.
>>  YourCountry will enable Country specific guidance. Linux experts in
>> YourCountry  can be found through: http://www.linux.org/groups/index.html.
>> They will know your Country's modem code, which may be essential for
>> dialup service.
>> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
>> Internet Provider m`ail filters.
>>  So in a day, also check the Archived responses at
>> http://www.linmodems.org
>> --------------------------  System information
>> ---------------------------- CPU=i686,  Ubuntu ,  ALSA_version=1.0.24
>> Linux version 3.0.0-12-generic
>> (buildd@vernadsky) (gcc version 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) )
>> #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011  scanModem update of:
>> 2011_08_08
>>
>> Distrib_ID=Ubuntu
>> DistribCodeName=oneiric
>> AptRepositoryStem=http://us.archive.ubuntu.com/ubuntu/
>>
>>
>> Presently install your Linux Distributions dkms package. It provides
>> for automated driver updates, following upgrade of your kernel.  For
>> details see http://linux.dell.com/projects.shtml#dkms
>>
>>  There are no blacklisted modem drivers in /etc/modprobe*  files
>>
>>  Potentially useful modem drivers now loaded are:
>>
>>
>> Attached USB devices are:
>>  ID 152d:2329 JMicron Technology Corp. / JMicron USA Technology Corp.
>> JM20329 SATA Bridge  ID 062a:0000 Creative Labs Optical mouse If a
>> cellphone is not detected, see
>> http://ubuntuforums.org/archive/index.php/t-878554.html
>> A sample report is:
>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>>
>> If a USB modem or cellphone is attached and was not detected, please
>> provide available information in your request to discuss@xxxxxxxxxxxxx
>>
>> Candidate PCI devices with modem chips are:
>> 01:01.0 Modem: Intel Corporation FA82537EP 56K V.92 Data/Fax Modem PCI
>> (rev
>> 04) High Definition Audio cards can host modem chips.
>>
>> For candidate card in slot 01:01.0, firmware information and bootup
>> diagnostics are:
>>  PCI slot       PCI ID          SubsystemID     Name
>>  ----------     ---------       ---------       --------------
>>  01:01.0        8086:1080       1028:1000       Modem: Intel
>> Corporation FA82537EP 56K V.92 Data/Fax Modem PCI
>>
>>  Modem interrupt assignment and sharing:
>>  --- Bootup diagnostics for card in PCI slot 01:01.0 ---- [
>> 0.165277] pci 0000:01:01.0: [8086:1080] type 0 class 0x000703 [
>> 0.165296] pci 0000:01:01.0: reg 10: [mem 0xfeafe000-0xfeafefff] [
>> 0.165306] pci 0000:01:01.0: reg 14: [io  0xde00-0xdeff] [    0.165366]
>> pci 0000:01:01.0: PME# supported from D0 D3hot D3cold [    0.165371]
>> pci 0000:01:01.0: PME# disabled [    0.640344] serial 0000:01:01.0:
>> PCI INT A -> GSI 22 (level, low) -> IRQ
>> 22
>> [    0.640536] 0000:01:01.0: ttyS5 at I/O 0xde08 (irq = 22) is a 16450
>> [    0.640645] 0000:01:01.0: ttyS6 at I/O 0xde10 (irq = 22) is a 8250
>> [    0.640751] 0000:01:01.0: ttyS7 at I/O 0xde18 (irq = 22) is a 16450
>> [    0.640860] 0000:01:01.0: ttyS8 at I/O 0xde20 (irq = 22) is a 8250
>> [    0.640969] 0000:01:01.0: ttyS9 at I/O 0xde28 (irq = 22) is a 8250
>> [    0.641611] 0000:01:01.0: ttyS16 at I/O 0xde60 (irq = 22) is a 8250
>>
>>  The PCI slot 01:01.0 of the modem card may be disabled early in  a
>> bootup process,  but then enabled later. If modem drivers load  but
>> the  modem is not responsive, read DOCs/Bootup.txt about possible fixes.
>>  Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx  if
>> help is needed.
>>
>>
>> === Finished firmware and bootup diagnostics, next deducing cogent
> software.
>> ===
>>
>> Predictive  diagnostics for card in bus 01:01.0:
>>        Modem chipset  detected on
>> NAME="Modem: Intel Corporation FA82537EP 56K V.92 Data/Fax Modem PCI "
>> CLASS=0703
>> PCIDEV=8086:1080
>> SUBSYS=1028:1000
>> IRQ=22
>> IDENT=INTEL537EP
>>
>>  For candidate modem in:  01:01.0
>>   0703 Modem: Intel Corporation FA82537EP 56K V.92 Data/Fax Modem PCI
>>      Primary device ID:  8086:1080
>>  Support type needed or chipset:        INTEL537EP
>>
>>
>>
>>  Since 2006, Intel appears to have ceased its modem code updates for
> Linux.
>>  The outdated official Intel support packages can be accessed through:
>>       http://developer.intel.com/design/modems/support/drivers.htm
>>  Beneficially, Philippe Vouters has been provided updates as the Linux
>> kernel evolves.
>>  But intensive personal support is not feasible, see:
>> http://archives.linmodems.org/24939
>>  The code for the INTEL537 and INTEL536 chipset modems is now at:
>>      http://vouters.dyndns.org/Intel/ , previously http://x9000.fr
>> Copies are also stored at:
>>       http://linmodems.technion.ac.il/packages/intel/Philippe.Vouters/
>> For Ubuntu Linux users with Intel 536 and 537 chipsets, there are
>> driver installation packages available thru
>> http://groups.google.com/group/ubuntu-modems
>>
>>  Read DOCs/Intel.txt and Modem/DOCs/YourSystem.txt for follow through
>> guidance.
>>
>>
>> Writing DOCs/Intel.txt
>>
>>  Completed candidate modem analyses.
>>
>>  The base of the UDEV device file system is: /dev/.udev
>>
>>  Versions adequately match for the compiler installed: 4.6.1
>>             and the compiler used in kernel assembly: 4.6.1
>>
>>  linux-headers-3.0.0-12-generic resources needed for compiling are not
>> manifestly ready!
>>  The patch utility is needed for compiling ALSA drivers, and possibly
>> others.
>>
>>  If compiling is necessary packages must be installed, providing:
>>         linux-headers-3.0.0-12-generic
>>
>>
>> If a driver compilation fails, with message including some lack of
>> some FileName.h (stdio.h for example), then Some additional
>> kernel-header files need installation to /usr/include. The minimal
>> additional packages are libc6-dev and any of its dependents, under
>> Ubuntu linux-libc-dev
>>
>> If an alternate ethernet connection is available, $  apt-get update $
>> apt-get -s install linux-kernel-devel will install needed packages.
>> For Debian/Ubuntu related distributions, run the following command to
>> display the needed package list:
>>
>> Otherwise packages have to be found through http://packages.ubuntu.com
>> Once downloaded and transferred into a Linux partition, they can be
>> installed alltogether with:
>> $ sudo dpkg -i *.deb
>>
>> Checking settings of:   /etc/ppp/options asyncmap 0 noauth crtscts
>> lock hide-password modem lcp-echo-interval 30 lcp-echo-failure 4 noipx
>>
>> In case of a message like:
>>   Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
>> see
>> http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>>
>> For guidance on FAX usage, get from
>> http://linmodems.technion.ac.il/packages/  get faxing.tar.gz It has
>> samples for a modem using port /dev/ttySL0, which must be changed to
>> match your modem's port.
>>
>> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
>> Which can interfere with Browser naviagation.
>>
>>  Don't worry about the following, it is for experts should trouble
>> shooting be necessary.
>> ==========================================================
>>
>>  Checking for modem support lines:
>>  --------------------------------------
>>     /device/modem symbolic link:
>> slmodemd created symbolic link /dev/ttySL0:
>>     Within /etc/udev/ files:
>>
>>     Within /etc/modprobe.conf files:
>> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in
>> order to blacklist unwanted modem drivers
>> /etc/modprobe.d/blacklist-modem.conf:#
>> blacklist snd-atiixp-modem /etc/modprobe.d/blacklist-modem.conf:#
>> blacklist snd-via82xx-modem /etc/modprobe.d/alsa-base.conf:options
>> snd-atiixp-modem
>> index=-2 /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem
>> index=-2
>>     Within any ancient /etc/devfs files:
>>
>>     Within ancient kernel 2.4.n /etc/module.conf files:
>>
>> --------- end modem support lines --------
>>
>>
>> ~Andrew Merczynski-Hait
>>
>>
>



[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux