Re: TP-LINK External Serial Modem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


"Jacques Goldberg" <Jacques.Goldberg@xxxxxxx> escribió:

You are right.

I had not understood that you continue to use the modem associated with /dev/ttySL0

Please send me a copy of the file /etc/wvdial.conf which you use to connect using ttySL0
i have the 2 configuration in the same file wvdial.conf this is the configuration of the external modem tp-link

[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = 060110
ISDN = 0
Username = islanis@xxxxxxxxxxxxxx
Init1 = ATZ
Password = **************
Modem = /dev/ttyS0
Baud = 115200


the other configuration i dont have it here because ia am in the work right now


The command mv /etc/wvdial.conf myfile.txt makes a copy without changing the original file.

Please hide the password   as you had done before.

I will send you a file modified to use the TP-LINK modem and instructions how to use it .

I also need to know what you do to start the other modem before giving the command wvdial to use it, because there are several ways to do it.

Do you give a command slmodemd to start the driver just before you need to connect, or is the driver started automatically when you boot?

let see, to start the external modem , the tp-link i use

wvdial

to start the smartlink internal modem i use

wvdial interno

later i'll send yopu the entire file ok,,

and i conect only of that way, i dont use the way that are you saying



On 07/13/2011 05:33 PM, islanis@xxxxxxxxxxxxxx wrote:

"Jacques Goldberg" <Jacques.Goldberg@xxxxxxx> escribió:

Juan,

1-In the listing which you have sent, islanis.txt, there is outout of the first four commands only.
The output for

wvdial |  tee  -a  islanis.txt

here is the missing part


root@ubuntu:/home/juan# wvdial
--> WvDial: Internet dialer version 1.60
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
-> Sending: ATDT060110
--> Waiting for carrier.
ATDT060110
--> Timed out while dialing.  Trying again.
--> Sending: ATDT060110
--> Waiting for carrier.
ATDT060110







is missing.

So I cannot know what happens when you try to connect with wvdial  !!!

Also your /etc/wvdial.conf   contains a section for   /dev/ttySL0

And finally   /dev/modem  too points to   /dev/ttySL0

This ambiguity between    ttySL0 and ttyS0 may fool the system.

If wvdial tries to start ttySL0 but it is your TP-LINK that is connected to the wall, it cannot connect to the phone company, and this is exactly the problem which you reported.

Please try

1-to remove /dev/modem       with command     rm/dev/modem
2-to remove the script which starts /dev/ttySL0 if it is still there. A way to know for sure is the command lsmod which should NOT show the driver for the other modem (the one you used before trying to use TP-LINK)
3-to remove   /etc/wvdial.conf     with command    rm  /etc/wvdial.conf
4-to run wvdialconf again
5-to edit it for the username, phone number, and password as you have done
6-to start    wvdial
ok so, you say that i have to delete /dev/modem and /dev/ttysl0, but if i delete them, how i'll comunicate with you, because the smartlink modem is the way that i am using to comunicate with you, if this, later of this action can not work properly how can i restart de configuration to send you the other parts,am afraid of that,remember that i am new in this world,and other peoples said to me that i can have working some mothems in the same operating system, help please
with a very simple basic /etc/wvdial.conf conaining only ONE modem , /dev/ttyS0

What you sent definitely shows that the software is recognizing the TP-LINK modem as expected. Thus, if wvdial fails, it can only be because the file /etc/wvdial.conf is bad.

This is why I suggested that you rebuild it from the beginning without adding sophistications.

Jacques

On 07/13/2011 07:53 AM, juan alejandro martines linares wrote
El mié, 13-07-2011 a las 10:59 0300, Jacques Goldberg escribió:
Juan,

Can you please, AFTER HAVING VERIFIED THAT THE TP-LINK MODEM IS
CONNECTED TO PC AND WALL AND POWERED UP, give the  five following
commands as superuser (that is becoming su with most Linux
distributions, or prefixing each command with sudo if you use Debian or
Ubuntu or a variation of Ubuntu or any other variation of Debian) ?
They will create one file named    islanis.txt
Edit the file by replacing the password by xxx  and send me the file. Be
sure not to leave your  password visible when sending the file,

ls -l /dev/ttyS*>  islanis.txt
ls -l /dev/modem>>   islanis.txt
cat /etc/wvdial.conf>>   islanis.txt
wvdialconf  /etc/wvdial.conf  |  tee  -a  islanis.txt
wvdial |  tee  -a  islanis.txt

here is all the requested info, the file islanis.txt

crw-rw---- 1 root dialout 4, 64 2011-07-13 06:45 /dev/ttyS0
crw-rw---- 1 root dialout 4, 65 2011-07-13 06:29 /dev/ttyS1
crw-rw---- 1 root dialout 4, 66 2011-07-13 06:29 /dev/ttyS2
crw-rw---- 1 root dialout 4, 67 2011-07-13 06:29 /dev/ttyS3
lrwxrwxrwx 1 root root       10 2011-07-13 06:29 /dev/ttySL0
->  /dev/pts/0
lrwxrwxrwx 1 root root 6 2011-07-13 06:29 /dev/modem ->  ttySL0

[Dialer Defaults]
Init = ATZ
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0&C1&D2 +FCLASS=0
#Stupid Mode = yes
Modem Type = Analog Modem
ISDN = 0
Phone = 060110
Modem = /dev/ttyS0
Username = islanis@xxxxxxxxxxxxxx
#Carrier Check = no
Password = ***********
Baud = 115200

[Dialer interno]
Init = ATZ
Init2 = ATQ0 V1 E1 S0=0 X3&C1&D2 +MS=90
Stupid Mode = yes
Modem Type = Analog Modem
ISDN = 0
Phone = 060110
Modem = /dev/ttySL0
Username = islanis@xxxxxxxxxxxxxx
Carrier Check = no
Password = *************
Baud = 460800
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.


Found a modem on /dev/ttyS0.
Modem configuration written to /etc/wvdial.conf.


Where you see>>  in these commands you MUST type  TWO>    with no space
between the two
Where you see |  in these commands  this is a vertical bar on your
keyboard, usually above \  at the RIGHT SIDE of your keyboard.

And please do not write in Spanish - I do not understand Spanish.
ok


Jacques




--

Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas

Infomed: http://www.sld.cu/





----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.


--

Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas

Infomed: http://www.sld.cu/





----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.


--

Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas

Infomed: http://www.sld.cu/



[Linux DVB]     [Asterisk]     [Photo]     [DCCP]     [Netdev]     [Xorg]     [Xfree86]     [Fedora Women]     [Linux USB]

Powered by Linux