Re: 047e:2892 Agere Systems, Inc. (Lucent) Systems Soft Modem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


PeM

While in principle this USB modem chipset 047e:2892
should be supported by these drivers, there has not been a single
success under Linux,
though several users have tested them.

PCI card modems are using the same drivers successfully.

Sadly there is no assistance we can provide because the USB component
is substantially in the Closed Source (precompiled) component of the
code package.
Your best option is a modem which uses the Open Source linux drivers
present in any linux distribution.
Sadly, "modems in a box" rarely provide detail as to the drivers used,
so we cannot provide precise guidance as to what alternative hardware.

Sincerely:

Marvin Stodolsky
scanModem maintainer

On Fri, Apr 1, 2011 at 12:34 PM, PeM <pierremarie.coron@xxxxxxxxx> wrote:
> Hello
>
> I'm running on UBUNTU server 10.04 since few days I'm trying to use this
> modem :
>
> ID 047e:2892 Agere Systems, Inc. (Lucent) Systems Soft Modem
>
> I've tried to install the agrsm driver using the tar.bz but I'm still
> blocking by this :
> "Pas de rÃgle pour fabriquer la cible  kernel/bounds.c Â, nÃcessaire
> pour  kernel/bounds.s Â. ArrÃt"
> so I've tried to use the deb file (agrsm-11c11040_20091225_i386.deb) and
> the install was made.
> I've modprobed the two modules agrserial and agrmodem without error and
> the devices /dev/ttyAGS3 and /dev/SAGR were created.
> It should be fine for the moment..
> When I try :
> sudo wvdialconf
> I've this answer :
>
> pem@passerelle:~/Modem$ sudo wvdialconf
> Editing `/etc/wvdial.conf'.
>
> Scanning your serial ports for a modem.
>
> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> Modem Port Scan<*1>: S1 Â S2 Â S3
> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> ttySHSF0<Info>: Device or resource busy
> Modem Port Scan<*1>: SHSF0 SHSF1 SHSF2 SHSF3 SHSF4
> Modem Port Scan<*1>: SHSF5 SHSF6 SHSF7
>
>
> Sorry, no modem was detected! ÂIs it in use by another program?
> Did you configure it properly with setserial?
>
> Please read the FAQ at http://open.nit.ca/wiki/?WvDial
>
> If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>.
> pem@passerelle:~/Modem$
>
> I've read post witch purpose tu change grub options with acpi=off and
> disable the bios sound option without result..
>
> Does anybody could help me please?
>
> Perhaps this modem don't work at all with this driver?
>
> I apologies for my poor English...
> Best regards
>
>
>



[Linux DVB]     [Asterisk]     [Photo]     [DCCP]     [Netdev]     [Xorg]     [Xfree86]     [Fedora Women]     [Linux USB]

Powered by Linux