Re: ModemData.txt dmsg.txt output after scanMode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


Hi,

having more than one PCI device on the same interrupt isn't a concern in most cases. If you beleive that "nouveau" is interferring with the HCF driver, you can always unload "nouveau" (might require to stop Xorg and use a virtual terminal (i.e. Ctrl+Alt+F1) to do that) and try to use the modem again. With the limited information provided, I don't see a problem with the driver, it seems to be ready to use.

If you require more assistance, you should send a dump file generated with the 'hcfpciconfig --dumpdiag' command in a root shell to support@xxxxxxxxxxxx, this information will help us find the source of the problem, if any.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
support@xxxxxxxxxxxx


JESÚS VERA GIMENEZ wrote:
Thank you Antonio.
I'll wait for Jonathan's reaction
Jesús

On Nov 26, 2010, at 6:47 PM, Antonio Olivares wrote:

Jesus,

Something is causing the driver to not work correctly, i.e, a
conflict.  Novuevau and modem hcfpcimodem are sharing resources and
this is causing the modem to fail :(

Modem interrupt assignment and sharing:
16:          4   IO-APIC-fasteoi   nouveau, hcfpcihw

[  924.781371] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  960.815473] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  961.595176] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  961.851799] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  963.182548] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  963.882184] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  984.612035] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.

Hopefully Jonathan (Linuxant support) has some suggestions you can try out.

Regards,

Antonio

On Fri, Nov 26, 2010 at 4:24 AM, jvg <macjvg@xxxxxxxxx> wrote:
Greetings to everyone.
It follows scanMode output after following instructions on installing
modem-fax pci software on Ubuntu 10.10. It doesn't work neither
Any help will be appreciated.
Regards,

Jesús

ModemData.txt------------------------------------

 Only plain text email is forwarded by the  Discuss@xxxxxxxxxxxxx List
Server,
 as HTML can contain viruses. Use as the email Subject Line:
          YourName, YourCountry  kernel 2.6.35-22-generic
 With this Subject Line cogent experts will be alerted, and useful case
names left in the Archive.
 YourCountry will enable Country specific guidance. Linux experts in
YourCountry
 can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for
dialup service.
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
Internet Provider mail filters.
 So in a day, also check the Archived responses at
http://www.linmodems.org
--------------------------  System information
----------------------------
CPU=i686,  Ubuntu ,  ALSA_version=1.0.23
Linux version 2.6.35-22-generic (buildd@vernadsky) (gcc version 4.4.5
(Ubuntu/Linaro 4.4.4-14ubuntu5) ) #35-Ubuntu SMP Sat Oct 16 20:36:48 UTC
2010
 scanModem update of:  2010_05_29
The modem symbolic link is /dev/modem -> ttySHCF0
Distrib_ID=Ubuntu
DistribCodeName=maverick
AptRepositoryStem=http://es.archive.ubuntu.com/ubuntu/


The dkms driver upgrade utilities are installed,

 There are no blacklisted modem drivers in /etc/modprobe*  files

 Potentially useful modem drivers now loaded are:
         slamr

slamrTest=
Attached USB devices are:
 ID 06bd:2091 AGFA-Gevaert NV SnapScan e20
 ID ffc0:0001
 ID 0783:0006 C3PO LTC31v2
 ID 047f:0ca1 Plantronics, Inc. USB DSP v4 Audio Interface
 ID 058f:6362 Alcor Micro Corp. Flash Card Reader/Writer
 ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B Wireless 802.11g
54Mbps Network Adapter
If a cellphone is not detected, see
http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html

If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx

Candidate PCI devices with modem chips are:
00:0c.0 Communication controller: Conexant Systems, Inc. HCF 56k
Data/Fax Modem (rev 08)
High Definition Audio cards can host modem chips.

For candidate card in slot 00:0c.0, firmware information and bootup
diagnostics are:
 PCI slot       PCI ID          SubsystemID     Name
 ----------     ---------       ---------       --------------
00:0c.0 14f1:1033 1092:0ac8 Communication controller: Conexant Systems,
Inc. HCF 56k Data/Fax Modem

 Modem interrupt assignment and sharing:
 16:          4   IO-APIC-fasteoi   nouveau, hcfpcihw
 --- Bootup diagnostics for card in PCI slot 00:0c.0 ----
[    0.115157] pci 0000:00:0c.0: reg 10: [mem 0xfebe0000-0xfebeffff]
[    0.115169] pci 0000:00:0c.0: reg 14: [io  0xc000-0xc007]
[    0.115227] pci 0000:00:0c.0: PME# supported from D0 D3hot D3cold
[    0.115235] pci 0000:00:0c.0: PME# disabled
[  499.897864] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  501.765444] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  503.018257] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  505.215408] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  506.805357] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  924.781371] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  960.815473] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  961.851799] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  963.182548] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 2303.485359] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 2303.721466] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 3607.929090] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 3646.336789] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 3984.717732] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 4021.495374] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 4022.446913] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 4023.825258] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16

 The PCI slot 00:0c.0 of the modem card may be disabled early in
 a bootup process,  but then enabled later. If modem drivers load
 but the  modem is not responsive, read DOCs/Bootup.txt about possible
fixes.
 Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
 if help is needed.


=== Finished firmware and bootup diagnostics, next deducing cogent
software. ===

Predictive  diagnostics for card in bus 00:0c.0:
       Modem chipset not detected on
NAME="Communication controller: Conexant Systems, Inc. HCF 56k Data/Fax
Modem "
CLASS=0780
PCIDEV=14f1:1033
SUBSYS=1092:0ac8
IRQ=16
IDENT=hcfpcimodem

 For candidate modem in:  00:0c.0

     Primary device ID:
 Support type needed or chipset:


 Completed candidate modem analyses.

 The base of the UDEV device file system is: /dev/.udev

 Versions adequately match for the compiler installed: 4.4.5
            and the compiler used in kernel assembly: 4.4.5

 linux-headers-2.6.35-22-generic resources needed for compiling are not
manifestly ready!

 If compiling is necessary packages must be installed, providing:
        linux-headers-2.6.35-22-generic


If a driver compilation fails, with message including some lack of some
FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include.
The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev

If an alternate ethernet connection is available,
$  apt-get update
$  apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to
display the needed package list:

Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb

Checking settings of:   /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx

In case of a message like:
  Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html

For guidance on FAX usage, get from
http://linmodems.technion.ac.il/packages/  get faxing.tar.gz
It has samples for a modem using port /dev/ttySL0, which must be changed
to match your modem's port.

Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth1
wlan0 wlan3
Which can interfere with Browser naviagation.

 Don't worry about the following, it is for experts should trouble
shooting be necessary.
==========================================================

 Checking for modem support lines:
 --------------------------------------
    /device/modem symbolic link:   lrwxrwxrwx 1 root root 8 2010-11-26
10:06 /dev/modem -> ttySHCF0
slmodemd created symbolic link /dev/ttySL0:
    Within /etc/udev/ files:
/etc/udev/rules.d/00-hcfpci.rules:KERNEL=="ttySHCF0", SYMLINK="modem"
    Within /etc/modprobe.conf files:
/etc/modprobe.d/sl-modem.conf:install slamr /sbin/modprobe -qb
ungrab-winmodem; /sbin/modprobe --ignore-install slamr; test
-e /dev/slamr0 && (chmod 660 /dev/slamr0 && chgrp dialout /dev/slamr0)
|| (/bin/mknod -m 660 /dev/slamr0 c 242 0 2>/dev/null && chgrp
dialout /dev/slamr0)
/etc/modprobe.d/sl-modem.conf:install slusb /sbin/modprobe -qb
ungrab-winmodem; /sbin/modprobe --ignore-install slusb; test
-e /dev/slusb0 && (chmod 660 /dev/slusb0 && chgrp dialout /dev/slusb0)
|| (/bin/mknod -m 660 /dev/slusb0 c 243 0 2>/dev/null && chgrp
dialout /dev/slusb0)
/etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
/etc/modprobe.d/hcfpci.conf:alias /dev/modem /dev/ttySHCF
/etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order
to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
    Within any ancient /etc/devfs files:
    Within ancient kernel 2.4.n /etc/module.conf files:
/etc/modules.conf:alias /dev/modem /dev/ttySHCF
--------- end modem support lines --------

-------------------------------------------------------dmsg.txt--------------------------
          CPU0
 0:         48   IO-APIC-edge      timer
 1:       5771   IO-APIC-edge      i8042
 6:          3   IO-APIC-edge      floppy
 7:          0   IO-APIC-edge      parport0
 8:          0   IO-APIC-edge      rtc0
 9:          0   IO-APIC-fasteoi   acpi
 14:          0   IO-APIC-edge      pata_via
 15:        356   IO-APIC-edge      pata_via
 16:          4   IO-APIC-fasteoi   nouveau, hcfpcihw
 17:          0   IO-APIC-fasteoi   eth1
 18:         69   IO-APIC-fasteoi   Ensoniq AudioPCI
 19:      58862   IO-APIC-fasteoi   b43
 20:      34590   IO-APIC-fasteoi   sata_via
 21:     577982   IO-APIC-fasteoi   ehci_hcd:usb1, uhci_hcd:usb2,
uhci_hcd:usb3, uhci_hcd:usb4, uhci_hcd:usb5
 23:          0   IO-APIC-fasteoi   eth0
NMI:          0   Non-maskable interrupts
LOC:    1877035   Local timer interrupts
SPU:          0   Spurious interrupts
PMI:          0   Performance monitoring interrupts
PND:          0   Performance pending work
RES:          0   Rescheduling interrupts
CAL:          0   Function call interrupts
TLB:          0   TLB shootdowns
TRM:          0   Thermal event interrupts
THR:          0   Threshold APIC interrupts
MCE:          0   Machine check exceptions
MCP:         17   Machine check polls
ERR:          0
MIS:          0

[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.35-22-generic (buildd@vernadsky) (gcc
version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #35-Ubuntu SMP Sat Oct
16 20:36:48 UTC 2010 (Ubuntu 2.6.35-22.35-generic 2.6.35.4)
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000
(reserved)
[    0.000000]  BIOS-e820: 00000000000e4000 - 0000000000100000
(reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000007ff30000 (usable)
[    0.000000]  BIOS-e820: 000000007ff30000 - 000000007ff40000 (ACPI
data)
[    0.000000]  BIOS-e820: 000000007ff40000 - 000000007fff0000 (ACPI
NVS)
[    0.000000]  BIOS-e820: 000000007fff0000 - 0000000080000000
(reserved)
[    0.000000]  BIOS-e820: 00000000fffc0000 - 0000000100000000
(reserved)
[    0.000000] NX (Execute Disable) protection: approximated by x86
segment limits
[    0.000000] DMI 2.3 present.
[    0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working
around it.
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[    0.000000] e820 update range: 0000000000000000 - 0000000000001000
(usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000
(usable)
[    0.000000] last_pfn = 0x7ff30 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-DFFFF uncachable
[    0.000000]   E0000-EFFFF write-through
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 000000000 mask F80000000 write-back
[    0.000000]   1 disabled
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new
0x7010600070106
[    0.000000] Scanning 0 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000009fc00 (usable)
[    0.000000]  modified: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000e4000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000007ff30000 (usable)
[    0.000000]  modified: 000000007ff30000 - 000000007ff40000 (ACPI
data)
[    0.000000]  modified: 000000007ff40000 - 000000007fff0000 (ACPI NVS)
[    0.000000]  modified: 000000007fff0000 - 0000000080000000 (reserved)
[    0.000000]  modified: 00000000fffc0000 - 0000000100000000 (reserved)
[    0.000000] initial memory mapped : 0 - 00c00000
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 15000-1a000
[    0.000000] RAMDISK: 375ac000 - 37ff0000
[    0.000000] Allocated new RAMDISK: 009a5000 - 013e86b5
[    0.000000] Move RAMDISK from 00000000375ac000 - 0000000037fef6b4 to
009a5000 - 013e86b4
[    0.000000] ACPI: RSDP 000f9bc0 00014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT 7ff30000 00030 (v01 A M I  OEMRSDT  10000428
MSFT 00000097)
[    0.000000] ACPI: FACP 7ff30200 00081 (v02 A M I  OEMFACP  10000428
MSFT 00000097)
[    0.000000] ACPI: DSDT 7ff30360 0342A (v01  P4V88 P4V88001 00000001
INTL 02002026)
[    0.000000] ACPI: FACS 7ff40000 00040
[    0.000000] ACPI: APIC 7ff30300 00052 (v01 A M I  OEMAPIC  10000428
MSFT 00000097)
[    0.000000] ACPI: OEMB 7ff40040 0003F (v01 A M I  OEMBIOS  10000428
MSFT 00000097)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1159MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x0007ff30
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x0007ff30
[    0.000000] On node 0 totalpages: 523967
[    0.000000] free_area_init_node: node 0, pgdat c07ffd40, node_mem_map
c13ea200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2319 pages used for memmap
[    0.000000]   HighMem zone: 294435 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI
0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e4000
[    0.000000] PM: Registered nosave memory: 00000000000e4000 -
0000000000100000
[    0.000000] Allocating PCI resources starting at 80000000 (gap:
80000000:7ffc0000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] early_res array is doubled to 64 at [16000 - 167ff]
[    0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:2
nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @c2400000 s36416 r0 d20928
u2097152
[    0.000000] pcpu-alloc: s36416 r0 d20928 u2097152 alloc=1*4194304
[    0.000000] pcpu-alloc: [0] 0 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519872
[    0.000000] Kernel command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.35-22-generic
root=UUID=901d9326-5b10-42f2-86b8-8bfb0192bba4 ro quiet splash
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] allocated 10481280 bytes of page_cgroup
[    0.000000] please try 'cgroup_disable=memory' option if you don't
want memory cgroups
[    0.000000] Subtract (42 early reservations)
[    0.000000]   #1 [0000001000 - 0000002000]   EX TRAMPOLINE
[    0.000000]   #2 [0000100000 - 00009a0adc]   TEXT DATA BSS
[    0.000000]   #3 [000009d800 - 0000100000]   BIOS reserved
[    0.000000]   #4 [00009a1000 - 00009a408d]             BRK
[    0.000000]   #5 [0000010000 - 0000011000]      TRAMPOLINE
[    0.000000]   #6 [0000011000 - 0000015000]     ACPI WAKEUP
[    0.000000]   #7 [0000015000 - 0000016000]         PGTABLE
[    0.000000]   #8 [00009a5000 - 00013e9000]     NEW RAMDISK
[    0.000000]   #9 [00013e9000 - 00013ea000]         BOOTMEM
[    0.000000]   #10 [00013ea000 - 00023ea000]         BOOTMEM
[    0.000000]   #11 [00023ea000 - 00023ea004]         BOOTMEM
[    0.000000]   #12 [00023ea040 - 00023ea100]         BOOTMEM
[    0.000000]   #13 [00023ea100 - 00023ea154]         BOOTMEM
[    0.000000]   #14 [00023ea180 - 00023ed180]         BOOTMEM
[    0.000000]   #15 [00023ed180 - 00023ed1f0]         BOOTMEM
[    0.000000]   #16 [00023ed200 - 00023f3200]         BOOTMEM
[    0.000000]   #17 [00023f3200 - 00023f3227]         BOOTMEM
[    0.000000]   #18 [00023f3240 - 00023f333c]         BOOTMEM
[    0.000000]   #19 [00023f3340 - 00023f3380]         BOOTMEM
[    0.000000]   #20 [00023f3380 - 00023f33c0]         BOOTMEM
[    0.000000]   #21 [00023f33c0 - 00023f3400]         BOOTMEM
[    0.000000]   #22 [00023f3400 - 00023f3440]         BOOTMEM
[    0.000000]   #23 [00023f3440 - 00023f3480]         BOOTMEM
[    0.000000]   #24 [00023f3480 - 00023f34c0]         BOOTMEM
[    0.000000]   #25 [00023f34c0 - 00023f3500]         BOOTMEM
[    0.000000]   #26 [00023f3500 - 00023f3540]         BOOTMEM
[    0.000000]   #27 [00023f3540 - 00023f3550]         BOOTMEM
[    0.000000]   #28 [00023f3580 - 00023f35ea]         BOOTMEM
[    0.000000]   #29 [00023f3600 - 00023f366a]         BOOTMEM
[    0.000000]   #30 [0002400000 - 000240e000]         BOOTMEM
[    0.000000]   #31 [0002600000 - 000260e000]         BOOTMEM
[    0.000000]   #32 [00023f5680 - 00023f5684]         BOOTMEM
[    0.000000]   #33 [00023f56c0 - 00023f56c4]         BOOTMEM
[    0.000000]   #34 [00023f5700 - 00023f5708]         BOOTMEM
[    0.000000]   #35 [00023f5740 - 00023f5748]         BOOTMEM
[    0.000000]   #36 [00023f5780 - 00023f5828]         BOOTMEM
[    0.000000]   #37 [00023f5840 - 00023f58a8]         BOOTMEM
[    0.000000]   #38 [00023f58c0 - 00023f98c0]         BOOTMEM
[    0.000000]   #39 [000240e000 - 000248e000]         BOOTMEM
[    0.000000]   #40 [000248e000 - 00024ce000]         BOOTMEM
[    0.000000]   #41 [000260e000 - 000300ce80]         BOOTMEM
[    0.000000] Initializing HighMem for node 0 (000377fe:0007ff30)
[    0.000000] Memory: 2048908k/2096320k available (4928k kernel code,
46960k reserved, 2336k data, 684k init, 1187016k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfff16000 - 0xfffff000   ( 932 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc0819000 - 0xc08c4000   ( 684 kB)
[    0.000000]       .data : 0xc05d030e - 0xc0818668   (2336 kB)
[    0.000000]       .text : 0xc0100000 - 0xc05d030e   (4928 kB)
[    0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[    0.000000] SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0,
CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000]  RCU-based detection of stalled CPUs is disabled.
[    0.000000]  Verbose stalled-CPUs detection is disabled.
[    0.000000] NR_IRQS:2304 nr_irqs:512
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1695.223 MHz processor.
[    0.004009] Calibrating delay loop (skipped), value calculated using
timer frequency.. 3390.44 BogoMIPS (lpj=6780892)
[    0.004020] pid_max: default: 32768 minimum: 301
[    0.004061] Security Framework initialized
[    0.004102] AppArmor: AppArmor initialized
[    0.004107] Yama: becoming mindful.
[    0.004224] Mount-cache hash table entries: 512
[    0.004517] Initializing cgroup subsys ns
[    0.004527] Initializing cgroup subsys cpuacct
[    0.004537] Initializing cgroup subsys memory
[    0.004558] Initializing cgroup subsys devices
[    0.004563] Initializing cgroup subsys freezer
[    0.004569] Initializing cgroup subsys net_cls
[    0.004626] CPU0: Hyper-Threading is disabled
[    0.004633] mce: CPU supports 4 MCE banks
[    0.004653] CPU0: Thermal monitoring enabled (TM1)
[    0.004672] Performance Events: Netburst events, Netburst P4/Xeon PMU
driver.
[    0.004694] ... version:                0
[    0.004699] ... bit width:              40
[    0.004703] ... generic registers:      18
[    0.004708] ... value mask:             000000ffffffffff
[    0.004713] ... max period:             0000007fffffffff
[    0.004718] ... fixed-purpose events:   0
[    0.004722] ... event mask:             000000000003ffff
[    0.009077] SMP alternatives: switching to UP code
[    0.028085] ACPI: Core revision 20100428
[    0.037427] ftrace: converting mcount calls to 0f 1f 44 00 00
[    0.037438] ftrace: allocating 21758 entries in 43 pages
[    0.040147] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.041291] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.083717] CPU0: Intel(R) Pentium(R) 4 CPU 1.70GHz stepping 02
[    0.084000] Brought up 1 CPUs
[    0.084000] Total of 1 processors activated (3390.44 BogoMIPS).
[    0.084000] devtmpfs: initialized
[    0.084039] regulator: core version 0.5
[    0.084097] Time:  8:59:29  Date: 11/26/10
[    0.084194] NET: Registered protocol family 16
[    0.084450] EISA bus registered
[    0.084474] ACPI: bus type pci registered
[    0.084685] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=1
[    0.084691] PCI: Using configuration type 1 for base access
[    0.086778] bio: create slab <bio-0> at 0
[    0.088355] ACPI: EC: Look up EC in DSDT
[    0.090682] ACPI: Executed 1 blocks of module-level executable AML
code
[    0.098420] ACPI: Interpreter enabled
[    0.098429] ACPI: (supports S0 S1 S4 S5)
[    0.098469] ACPI: Using IOAPIC for interrupt routing
[    0.113378] ACPI Warning: Incorrect checksum in table [OEMB] - 0xA3,
should be 0x95 (20100428/tbutils-314)
[    0.113584] ACPI: No dock devices found.
[    0.113594] PCI: Ignoring host bridge windows from ACPI; if
necessary, use "pci=use_crs" and report a bug
[    0.113840] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.114289] pci_root PNP0A03:00: host bridge window [io
0x0000-0x0cf7] (ignored)
[    0.114296] pci_root PNP0A03:00: host bridge window [io
0x0d00-0xffff] (ignored)
[    0.114302] pci_root PNP0A03:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[    0.114308] pci_root PNP0A03:00: host bridge window [mem
0x80000000-0xffffffff] (ignored)
[    0.114352] pci 0000:00:00.0: reg 10: [mem 0xf8000000-0xfbffffff
pref]
[    0.114792] pci 0000:00:01.0: supports D1
[    0.114847] pci 0000:00:09.0: reg 10: [io  0xb800-0xb8ff]
[    0.114860] pci 0000:00:09.0: reg 14: [mem 0xfebff400-0xfebff4ff]
[    0.114919] pci 0000:00:09.0: supports D1 D2
[    0.114923] pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold
[    0.114932] pci 0000:00:09.0: PME# disabled
[    0.114976] pci 0000:00:0a.0: reg 10: [io  0xbc00-0xbc3f]
[    0.115040] pci 0000:00:0a.0: supports D2
[    0.115073] pci 0000:00:0b.0: reg 10: [mem 0xfebfc000-0xfebfdfff]
[    0.115157] pci 0000:00:0c.0: reg 10: [mem 0xfebe0000-0xfebeffff]
[    0.115169] pci 0000:00:0c.0: reg 14: [io  0xc000-0xc007]
[    0.115227] pci 0000:00:0c.0: PME# supported from D0 D3hot D3cold
[    0.115235] pci 0000:00:0c.0: PME# disabled
[    0.115284] pci 0000:00:0f.0: reg 10: [io  0xec00-0xec07]
[    0.115296] pci 0000:00:0f.0: reg 14: [io  0xe800-0xe803]
[    0.115307] pci 0000:00:0f.0: reg 18: [io  0xe400-0xe407]
[    0.115318] pci 0000:00:0f.0: reg 1c: [io  0xe000-0xe003]
[    0.115330] pci 0000:00:0f.0: reg 20: [io  0xdc00-0xdc0f]
[    0.115341] pci 0000:00:0f.0: reg 24: [io  0xd800-0xd8ff]
[    0.115439] pci 0000:00:0f.1: reg 20: [io  0xfc00-0xfc0f]
[    0.115562] pci 0000:00:10.0: reg 20: [io  0xc400-0xc41f]
[    0.115603] pci 0000:00:10.0: supports D1 D2
[    0.115607] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.115616] pci 0000:00:10.0: PME# disabled
[    0.115683] pci 0000:00:10.1: reg 20: [io  0xc800-0xc81f]
[    0.115723] pci 0000:00:10.1: supports D1 D2
[    0.115727] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.115736] pci 0000:00:10.1: PME# disabled
[    0.115802] pci 0000:00:10.2: reg 20: [io  0xcc00-0xcc1f]
[    0.115842] pci 0000:00:10.2: supports D1 D2
[    0.115846] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.115855] pci 0000:00:10.2: PME# disabled
[    0.115923] pci 0000:00:10.3: reg 20: [io  0xd000-0xd01f]
[    0.115962] pci 0000:00:10.3: supports D1 D2
[    0.115967] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.115975] pci 0000:00:10.3: PME# disabled
[    0.116042] pci 0000:00:10.4: reg 10: [mem 0xfebff800-0xfebff8ff]
[    0.116105] pci 0000:00:10.4: supports D1 D2
[    0.116110] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.116118] pci 0000:00:10.4: PME# disabled
[    0.116209] HPET not enabled in BIOS. You might try hpet=force boot
option
[    0.116291] pci 0000:00:12.0: reg 10: [io  0xd400-0xd4ff]
[    0.116302] pci 0000:00:12.0: reg 14: [mem 0xfebffc00-0xfebffcff]
[    0.116362] pci 0000:00:12.0: supports D1 D2
[    0.116367] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot
D3cold
[    0.116375] pci 0000:00:12.0: PME# disabled
[    0.116482] pci 0000:01:00.0: reg 10: [mem 0xfd000000-0xfdffffff]
[    0.116493] pci 0000:01:00.0: reg 14: [mem 0xe8000000-0xefffffff
pref]
[    0.116525] pci 0000:01:00.0: reg 30: [mem 0xfeaf0000-0xfeafffff
pref]
[    0.116607] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.116615] pci 0000:00:01.0:   bridge window [io  0xf000-0x0000]
(disabled)
[    0.116625] pci 0000:00:01.0:   bridge window [mem
0xfca00000-0xfeafffff]
[    0.116634] pci 0000:00:01.0:   bridge window [mem
0xe7f00000-0xf7efffff pref]
[    0.116648] pci_bus 0000:00: on NUMA node 0
[    0.116660] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.132141] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14
15)
[    0.132341] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *10 11 14
15)
[    0.132530] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14
15)
[    0.132719] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 10 11 14
15)
[    0.132908] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[    0.133099] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[    0.133299] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[    0.133487] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14
15) *0, disabled.
[    0.133569] HEST: Table is not found!
[    0.133767] vgaarb: device added: PCI:0000:01:00.0,decodes=io
+mem,owns=io+mem,locks=none
[    0.133773] vgaarb: loaded
[    0.134117] SCSI subsystem initialized
[    0.134256] libata version 3.00 loaded.
[    0.134394] usbcore: registered new interface driver usbfs
[    0.134421] usbcore: registered new interface driver hub
[    0.134489] usbcore: registered new device driver usb
[    0.134825] ACPI: WMI: Mapper loaded
[    0.134832] PCI: Using ACPI for IRQ routing
[    0.134841] PCI: pci_cache_line_size set to 64 bytes
[    0.134983] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[    0.134990] reserve RAM buffer: 000000007ff30000 - 000000007fffffff
[    0.135214] NetLabel: Initializing
[    0.135220] NetLabel:  domain hash size = 128
[    0.135223] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.135249] NetLabel:  unlabeled traffic allowed by default
[    0.135372] Switching to clocksource tsc
[    0.151916] AppArmor: AppArmor Filesystem Enabled
[    0.151954] pnp: PnP ACPI init
[    0.151997] ACPI: bus type pnp registered
[    0.160017] pnp: PnP ACPI: found 13 devices
[    0.160024] ACPI: ACPI bus type pnp unregistered
[    0.160032] PnPBIOS: Disabled by ACPI PNP
[    0.160064] system 00:08: [io  0x0295-0x0296] has been reserved
[    0.160072] system 00:08: [io  0x03e0-0x03e7] has been reserved
[    0.160078] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.160084] system 00:08: [io  0x0800-0x087f] has been reserved
[    0.160090] system 00:08: [io  0x0400-0x041f] has been reserved
[    0.160105] system 00:09: [mem 0xfec80000-0xfec800ff] has been
reserved
[    0.160113] system 00:09: [mem 0xfec00000-0xfec00fff] could not be
reserved
[    0.160119] system 00:09: [mem 0xfee00000-0xfee00fff] has been
reserved
[    0.160126] system 00:09: [mem 0xfff80000-0xffffffff] could not be
reserved
[    0.160139] system 00:0c: [mem 0x00000000-0x0009ffff] could not be
reserved
[    0.160146] system 00:0c: [mem 0x000c0000-0x000dffff] could not be
reserved
[    0.160153] system 00:0c: [mem 0x000e0000-0x000fffff] could not be
reserved
[    0.160159] system 00:0c: [mem 0x00100000-0x7fffffff] could not be
reserved
[    0.197944] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.197951] pci 0000:00:01.0:   bridge window [io  disabled]
[    0.197963] pci 0000:00:01.0:   bridge window [mem
0xfca00000-0xfeafffff]
[    0.197972] pci 0000:00:01.0:   bridge window [mem
0xe7f00000-0xf7efffff pref]
[    0.198003] pci 0000:00:01.0: setting latency timer to 64
[    0.198013] pci_bus 0000:00: resource 0 [io  0x0000-0xffff]
[    0.198018] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[    0.198024] pci_bus 0000:01: resource 1 [mem 0xfca00000-0xfeafffff]
[    0.198030] pci_bus 0000:01: resource 2 [mem 0xe7f00000-0xf7efffff
pref]
[    0.198109] NET: Registered protocol family 2
[    0.198239] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[    0.198805] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[    0.200151] TCP bind hash table entries: 65536 (order: 7, 524288
bytes)
[    0.200899] TCP: Hash tables configured (established 131072 bind
65536)
[    0.200906] TCP reno registered
[    0.200919] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.200944] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.201165] NET: Registered protocol family 1
[    0.201220] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[    0.201373] pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert
Message
[    0.201402] pci 0000:01:00.0: Boot video device
[    0.201409] PCI: CLS 32 bytes, default 64
[    0.201725] cpufreq-nforce2: No nForce2 chipset.
[    0.201793] Scanning for low memory corruption every 60 seconds
[    0.202042] audit: initializing netlink socket (disabled)
[    0.202067] type=2000 audit(1290761969.200:1): initialized
[    0.218113] Trying to unpack rootfs image as initramfs...
[    0.237237] highmem bounce pool size: 64 pages
[    0.237252] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.244817] VFS: Disk quotas dquot_6.5.2
[    0.244998] Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[    0.246420] fuse init (API version 7.14)
[    0.246656] msgmni has been set to 1683
[    0.253546] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[    0.253555] io scheduler noop registered
[    0.253559] io scheduler deadline registered
[    0.253598] io scheduler cfq registered (default)
[    0.253873] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.253919] pciehp: PCI Express Hot Plug Controller Driver version:
0.4
[    0.254310] input: Power Button
as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[    0.254324] ACPI: Power Button [PWRB]
[    0.254415] input: Power Button
as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    0.254423] ACPI: Power Button [PWRF]
[    0.254763] ACPI: acpi_idle registered with cpuidle
[    0.260226] ERST: Table is not found!
[    0.264754] isapnp: Scanning for PnP cards...
[    0.270593] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    0.270744] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.271506] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.278591] brd: module loaded
[    0.279703] loop: module loaded
[    0.280258]   alloc irq_desc for 20 on node -1
[    0.280265]   alloc kstat_irqs on node -1
[    0.280281] pata_acpi 0000:00:0f.1: PCI INT A -> GSI 20 (level, low)
-> IRQ 20
[    0.280370] pata_acpi 0000:00:0f.1: PCI INT A disabled
[    0.329151] Fixed MDIO Bus: probed
[    0.329236] PPP generic driver version 2.4.2
[    0.329391] tun: Universal TUN/TAP device driver, 1.6
[    0.329396] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[    0.329595] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[    0.329654]   alloc irq_desc for 21 on node -1
[    0.329659]   alloc kstat_irqs on node -1
[    0.329675] ehci_hcd 0000:00:10.4: PCI INT C -> GSI 21 (level, low)
-> IRQ 21
[    0.329709] ehci_hcd 0000:00:10.4: EHCI Host Controller
[    0.329820] ehci_hcd 0000:00:10.4: new USB bus registered, assigned
bus number 1
[    0.329925] ehci_hcd 0000:00:10.4: irq 21, io mem 0xfebff800
[    0.340939] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[    0.341289] hub 1-0:1.0: USB hub found
[    0.341301] hub 1-0:1.0: 8 ports detected
[    0.341449] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.341487] uhci_hcd: USB Universal Host Controller Interface driver
[    0.341579] uhci_hcd 0000:00:10.0: PCI INT A -> GSI 21 (level, low)
-> IRQ 21
[    0.341597] uhci_hcd 0000:00:10.0: UHCI Host Controller
[    0.341710] uhci_hcd 0000:00:10.0: new USB bus registered, assigned
bus number 2
[    0.341752] uhci_hcd 0000:00:10.0: irq 21, io base 0x0000c400
[    0.342036] hub 2-0:1.0: USB hub found
[    0.342048] hub 2-0:1.0: 2 ports detected
[    0.342172] uhci_hcd 0000:00:10.1: PCI INT A -> GSI 21 (level, low)
-> IRQ 21
[    0.342188] uhci_hcd 0000:00:10.1: UHCI Host Controller
[    0.342288] uhci_hcd 0000:00:10.1: new USB bus registered, assigned
bus number 3
[    0.342327] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000c800
[    0.342603] hub 3-0:1.0: USB hub found
[    0.342615] hub 3-0:1.0: 2 ports detected
[    0.342745] uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low)
-> IRQ 21
[    0.342761] uhci_hcd 0000:00:10.2: UHCI Host Controller
[    0.342867] uhci_hcd 0000:00:10.2: new USB bus registered, assigned
bus number 4
[    0.342908] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000cc00
[    0.343201] hub 4-0:1.0: USB hub found
[    0.343213] hub 4-0:1.0: 2 ports detected
[    0.343342] uhci_hcd 0000:00:10.3: PCI INT B -> GSI 21 (level, low)
-> IRQ 21
[    0.343357] uhci_hcd 0000:00:10.3: UHCI Host Controller
[    0.343457] uhci_hcd 0000:00:10.3: new USB bus registered, assigned
bus number 5
[    0.343495] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000d000
[    0.343766] hub 5-0:1.0: USB hub found
[    0.343777] hub 5-0:1.0: 2 ports detected
[    0.344008] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[    0.344014] PNP: PS/2 appears to have AUX port disabled, if this is
incorrect please boot with i8042.nopnp
[    0.344264] serio: i8042 KBD port at 0x60,0x64 irq 1
[    0.344518] mice: PS/2 mouse device common for all mice
[    0.344827] rtc_cmos 00:02: RTC can wake from S4
[    0.344924] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    0.344991] rtc0: alarms up to one year, y3k, 114 bytes nvram
[    0.345252] device-mapper: uevent: version 1.0.3
[    0.348880] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05)
initialised: dm-devel@xxxxxxxxxx
[    0.355518] device-mapper: multipath: version 1.1.1 loaded
[    0.355528] device-mapper: multipath round-robin: version 1.0.0
loaded
[    0.355924] EISA: Probing bus 0 at eisa.0
[    0.355974] EISA: Detected 0 cards.
[    0.360812] cpuidle: using governor ladder
[    0.360819] cpuidle: using governor menu
[    0.361565] TCP cubic registered
[    0.361879] NET: Registered protocol family 10
[    0.362652] lo: Disabled Privacy Extensions
[    0.363131] NET: Registered protocol family 17
[    0.363249] Using IPI No-Shortcut mode
[    0.363476] PM: Resume from disk failed.
[    0.363513] registered taskstats version 1
[    0.363913]   Magic number: 2:275:979
[    0.364062] rtc_cmos 00:02: setting system clock to 2010-11-26
08:59:29 UTC (1290761969)
[    0.364071] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    0.364075] EDD information not available.
[    0.369008] input: AT Translated Set 2 keyboard
as /devices/platform/i8042/serio0/input/input2
[    0.948904] isapnp: No Plug & Play device found
[    1.004753] usb 1-4: new high speed USB device using ehci_hcd and
address 4
[    1.181425] Freeing initrd memory: 10512k freed
[    1.195852] Freeing unused kernel memory: 684k freed
[    1.197022] Write protecting the kernel text: 4932k
[    1.197090] Write protecting the kernel read-only data: 1976k
[    1.251206] udev[63]: starting version 163
[    1.320116] usb 1-7: new high speed USB device using ehci_hcd and
address 6
[    1.773567] Floppy drive(s): fd0 is 1.44M
[    1.798520] sata_via 0000:00:0f.0: version 2.6
[    1.798553] sata_via 0000:00:0f.0: PCI INT B -> GSI 20 (level, low)
-> IRQ 20
[    1.798633] sata_via 0000:00:0f.0: routed to hard irq line 10
[    1.800759] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22,
2004)
[    1.808071] usb 2-1: new full speed USB device using uhci_hcd and
address 2
[    1.822267] scsi0 : sata_via
[    1.826678] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald
Becker
[    1.838931] FDC 0 is a post-1991 82077
[    1.842175] scsi1 : sata_via
[    1.842307] ata1: SATA max UDMA/133 cmd 0xec00 ctl 0xe800 bmdma
0xdc00 irq 20
[    1.842314] ata2: SATA max UDMA/133 cmd 0xe400 ctl 0xe000 bmdma
0xdc08 irq 20
[    1.842446] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an
8139C+ compatible chip, use 8139too
[    1.842507] pata_via 0000:00:0f.1: version 0.3.4
[    1.842536] pata_via 0000:00:0f.1: PCI INT A -> GSI 20 (level, low)
-> IRQ 20
[    1.862368] scsi2 : pata_via
[    1.876158] scsi3 : pata_via
[    1.880620] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00
irq 14
[    1.880628] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08
irq 15
[    1.889920]   alloc irq_desc for 23 on node -1
[    1.889928]   alloc kstat_irqs on node -1
[    1.889944] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low)
-> IRQ 23
[    1.891012] eth0: VIA Rhine II at 0xfebffc00, 00:0b:6a:a2:89:18, IRQ
23.
[    1.891730] eth0: MII PHY found at address 1, status 0x7849
advertising 05e1 Link 0000.
[    1.892531]   alloc irq_desc for 19 on node -1
[    1.892538]   alloc kstat_irqs on node -1
[    1.892553] b43-pci-bridge 0000:00:0b.0: PCI INT A -> GSI 19 (level,
low) -> IRQ 19
[    1.892619] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x04, vendor
0x4243)
[    1.892629] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x05,
vendor 0x4243)
[    1.892639] ssb: Core 2 found: PCMCIA (cc 0x80D, rev 0x02, vendor
0x4243)
[    1.892649] ssb: Core 3 found: V90 (cc 0x807, rev 0x02, vendor
0x4243)
[    1.892658] ssb: Core 4 found: PCI (cc 0x804, rev 0x09, vendor
0x4243)
[    1.911748] Initializing USB Mass Storage driver...
[    1.920509] ssb: Sonics Silicon Backplane found on PCI device
0000:00:0b.0
[    1.932580] scsi4 : usb-storage 1-7:1.0
[    1.941685] usbcore: registered new interface driver usb-storage
[    1.941694] USB Mass Storage support registered.
[    2.044084] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.234323] ata1.00: ATA-8: ST3500418AS, CC34, max UDMA/133
[    2.234333] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth
0/32)
[    2.276026] usb 3-1: new full speed USB device using uhci_hcd and
address 2
[    2.290345] ata1.00: configured for UDMA/133
[    2.290561] scsi 0:0:0:0: Direct-Access     ATA      ST3500418AS
CC34 PQ: 0 ANSI: 5
[    2.290941] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.291649] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500
GB/465 GiB)
[    2.291769] sd 0:0:0:0: [sda] Write Protect is off
[    2.291776] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.291825] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[    2.292233]  sda: sda1 sda2 < sda5 >
[    2.324420] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.492036] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.656394] ata2.00: ATA-6: ST380817AS, 3.42, max UDMA/133
[    2.656401] ata2.00: 156301488 sectors, multi 16: LBA48 NCQ (not
used)
[    2.672414] ata2.00: configured for UDMA/133
[    2.672640] scsi 1:0:0:0: Direct-Access     ATA      ST380817AS
3.42 PQ: 0 ANSI: 5
[    2.673006] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    2.673833] sd 1:0:0:0: [sdb] 156301488 512-byte logical blocks:
(80.0 GB/74.5 GiB)
[    2.673952] sd 1:0:0:0: [sdb] Write Protect is off
[    2.673959] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.674008] sd 1:0:0:0: [sdb] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[    2.674382]  sdb: sdb1 sdb2
[    2.692229] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.700032] usb 4-1: new low speed USB device using uhci_hcd and
address 2
[    2.844459] ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-4040B, A300, max
UDMA/33
[    2.844532] ata4.01: ATAPI: HL-DT-STDVD-ROM GDR8162B, 0015, max
UDMA/33
[    2.860428] ata4.00: configured for UDMA/33
[    2.875690] usbcore: registered new interface driver hiddev
[    2.876375] ata4.01: configured for UDMA/33
[    2.881375] input: Plantronics Plantronics Headset
as /devices/pci0000:00/0000:00:10.0/usb2/2-1/2-1:1.3/input/input3
[    2.881928] generic-usb 0003:047F:0CA1.0001: input,hidraw0: USB HID
v1.00 Device [Plantronics Plantronics Headset] on
usb-0000:00:10.0-1/input3
[    2.891585] scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-4040B
A300 PQ: 0 ANSI: 5
[    2.896097] sr0: scsi3-mmc drive: 32x/32x writer dvd-ram cd/rw
xa/form2 cdda tray
[    2.896106] Uniform CD-ROM driver Revision: 3.20
[    2.896430] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    2.896603] sr 3:0:0:0: Attached scsi generic sg2 type 5
[    2.899393] input: HID ffc0:0001
as /devices/pci0000:00/0000:00:10.2/usb4/4-1/4-1:1.0/input/input4
[    2.900469] generic-usb 0003:FFC0:0001.0002: input,hidraw1: USB HID
v1.10 Mouse [HID ffc0:0001] on usb-0000:00:10.2-1/input0
[    2.901035] usbcore: registered new interface driver usbhid
[    2.901045] usbhid: USB HID core driver
[    2.903308] scsi 3:0:1:0: CD-ROM            HL-DT-ST DVD-ROM GDR8162B
0015 PQ: 0 ANSI: 5
[    2.919720] sr1: scsi3-mmc drive: 20x/48x cd/rw xa/form2 cdda tray
[    2.920964] sr 3:0:1:0: Attached scsi CD-ROM sr1
[    2.921475] sr 3:0:1:0: Attached scsi generic sg3 type 5
[    2.979306] scsi 4:0:0:0: Direct-Access     Generic  USB SD Reader
1.00 PQ: 0 ANSI: 0
[    2.984938] scsi 4:0:0:1: Direct-Access     Generic  USB CF Reader
1.01 PQ: 0 ANSI: 0
[    2.985616] scsi 4:0:0:2: Direct-Access     Generic  USB SM Reader
1.02 PQ: 0 ANSI: 0
[    2.987226] scsi 4:0:0:3: Direct-Access     Generic  USB MS Reader
1.03 PQ: 0 ANSI: 0
[    2.990469] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[    3.002305] sd 4:0:0:0: Attached scsi generic sg4 type 0
[    3.008526] sd 4:0:0:1: [sdd] Attached SCSI removable disk
[    3.011463] sd 4:0:0:1: Attached scsi generic sg5 type 0
[    3.013704] sd 4:0:0:2: [sde] Attached SCSI removable disk
[    3.019434] sd 4:0:0:2: Attached scsi generic sg6 type 0
[    3.019976] sd 4:0:0:3: Attached scsi generic sg7 type 0
[    3.021456] sd 4:0:0:3: [sdf] Attached SCSI removable disk
[    3.036521] 8139too: 8139too Fast Ethernet driver 0.9.28
[    3.036594]   alloc irq_desc for 17 on node -1
[    3.036600]   alloc kstat_irqs on node -1
[    3.036616] 8139too 0000:00:09.0: PCI INT A -> GSI 17 (level, low) ->
IRQ 17
[    3.038186] 8139too 0000:00:09.0: eth1: RealTek RTL8139 at 0xb800,
00:02:44:37:94:06, IRQ 17
[    3.096144] usb 5-2: new full speed USB device using uhci_hcd and
address 2
[    3.423803] EXT4-fs (sda1): mounted filesystem with ordered data
mode. Opts: (null)
[   11.464833] Adding 6033404k swap on /dev/sda5.  Priority:-1 extents:1
across:6033404k
[   11.640258] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   11.648944] udev[347]: starting version 163
[   11.848822] lp: driver loaded but no devices found
[   12.284333] shpchp: Standard Hot Plug PCI Controller Driver version:
0.4
[   12.510863] Linux agpgart interface v0.103
[   12.542230] type=1400 audit(1290758381.674:2): apparmor="STATUS"
operation="profile_load" name="/sbin/dhclient3" pid=460
comm="apparmor_parser"
[   12.543171] type=1400 audit(1290758381.674:3): apparmor="STATUS"
operation="profile_load"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=460
comm="apparmor_parser"
[   12.543687] type=1400 audit(1290758381.674:4): apparmor="STATUS"
operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script"
pid=460 comm="apparmor_parser"
[   12.678390] WARNING! power/level is deprecated; use power/control
instead
[   12.745203] agpgart: Detected VIA PT880 chipset
[   12.891651] parport_pc 00:06: reported by Plug and Play ACPI
[   12.891785] parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   13.020283] agpgart-via 0000:00:00.0: AGP aperture is 64M @
0xf8000000
[   13.136496] lp0: using parport0 (interrupt-driven).
[   13.749280] cfg80211: Calling CRDA to update world regulatory domain
[   13.749438] gameport gameport0: NS558 PnP Gameport is
pnp00:07/gameport0, io 0x200, speed 774kHz
[   14.156396] ppdev: user-space parallel port driver
[   14.166028] cfg80211: World regulatory domain updated:
[   14.166039]     (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[   14.166046]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[   14.166053]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[   14.166059]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[   14.166065]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[   14.166071]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[   14.342222] [drm] Initialized drm 1.1.0 20060810
[   14.543343] b43-phy0: Broadcom 4306 WLAN found (core revision 5)
[   15.007851] phy0: Selected rate control algorithm 'minstrel'
[   15.009306] Registered led device: b43-phy0::tx
[   15.009353] Registered led device: b43-phy0::rx
[   15.009392] Registered led device: b43-phy0::radio
[   15.009566] Broadcom 43xx driver loaded [ Features: PL, Firmware-ID:
FW13 ]
[   15.009852] phy1: Selected rate control algorithm 'minstrel'
[   15.011345] phy1: hwaddr 00:e0:4c:8d:ab:4b, RTL8187BvE V0 +
rtl8225z2, rfkill mask 2
[   15.048889] rtl8187: Customer ID is 0x00
[   15.050291] Registered led device: rtl8187-phy1::radio
[   15.052352] Registered led device: rtl8187-phy1::tx
[   15.052887] Registered led device: rtl8187-phy1::rx
[   15.054631] rtl8187: wireless switch is on
[   15.055206] usbcore: registered new interface driver rtl8187
[   15.241118] udev[367]: renamed network interface wlan1 to wlan3
[   15.378019]   alloc irq_desc for 16 on node -1
[   15.378027]   alloc kstat_irqs on node -1
[   15.378043] nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) ->
IRQ 16
[   15.443374] [drm] nouveau 0000:01:00.0: Detected an NV10 generation
card (0x011000b2)
[   15.443743] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image
from PRAMIN
[   15.490461] [drm] nouveau 0000:01:00.0: ... appears to be valid
[   15.490652] [drm] nouveau 0000:01:00.0: BMP BIOS found
[   15.490657] [drm] nouveau 0000:01:00.0: BMP version 5.20
[   15.490663] [drm] nouveau 0000:01:00.0: Bios version 03.11.01.43
[   15.490670] [drm] nouveau 0000:01:00.0: Found Display Configuration
Block version 1.4
[   15.490675] [drm] nouveau 0000:01:00.0: No useful information in BIOS
output table; adding all possible outputs
[   15.490680] [drm] nouveau 0000:01:00.0: Probing TV encoders on I2C
bus: 1
[   15.536605] usbcore: registered new interface driver snd-usb-audio
[   15.559335]   alloc irq_desc for 18 on node -1
[   15.559342]   alloc kstat_irqs on node -1
[   15.559358] ENS1371 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) ->
IRQ 18
[   15.635068] eth1: link down
[   15.635910] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   15.727655] type=1400 audit(1290758384.858:5): apparmor="STATUS"
operation="profile_load" name="/usr/share/gdm/guest-session/Xsession"
pid=906 comm="apparmor_parser"
[   15.783164] type=1400 audit(1290758384.914:6): apparmor="STATUS"
operation="profile_replace" name="/sbin/dhclient3" pid=912
comm="apparmor_parser"
[   15.784558] type=1400 audit(1290758384.918:7): apparmor="STATUS"
operation="profile_replace"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=912
comm="apparmor_parser"
[   15.785084] type=1400 audit(1290758384.918:8): apparmor="STATUS"
operation="profile_replace"
name="/usr/lib/connman/scripts/dhclient-script" pid=912
comm="apparmor_parser"
[   15.929691] [drm] nouveau 0000:01:00.0: Detected TV encoder: ch7006
[   15.929882] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at
offset 0xB74C
[   15.929904] [drm] nouveau 0000:01:00.0: 0xB766: Failed parsing init
table opcode: INIT_CONFIGURE_PREINIT -19
[   15.929985] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at
offset 0xBE3A
[   15.929996] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at
offset 0xB767
[   15.930020] [drm] nouveau 0000:01:00.0: 0xB7F9: Failed parsing init
table opcode: INIT_CONFIGURE_CLK -19
[   15.930094] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at
offset 0xBDE1
[   15.930108] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at
offset 0xB7FA
[   15.930114] [drm] nouveau 0000:01:00.0: 0xB81E: Failed parsing init
table opcode: INIT_CONFIGURE_MEM -19
[   15.930189] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at
offset 0xB94E
[   15.930214] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 6 at
offset 0xB81F
[   15.930245] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 7 at
offset 0xB8E9
[   15.930257] [drm] nouveau 0000:01:00.0: Detected 64MiB VRAM
[   15.962512] type=1400 audit(1290758385.094:9): apparmor="STATUS"
operation="profile_load" name="/usr/bin/evince" pid=917
comm="apparmor_parser"
[   15.971296] [TTM] Zone  kernel: Available graphics memory: 436544
kiB.
[   15.971304] [TTM] Zone highmem: Available graphics memory: 1030052
kiB.
[   15.971308] [TTM] Initializing pool allocator.
[   15.971534] agpgart-via 0000:00:00.0: AGP 3.5 bridge
[   15.971564] agpgart-via 0000:00:00.0: bridge is in legacy mode,
falling back to 2.x
[   15.971575] agpgart-via 0000:00:00.0: putting AGP V2 device into 4x
mode
[   15.971697] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
[   15.971704] [drm] nouveau 0000:01:00.0: 64 MiB GART (aperture)
[   15.973169] [drm] nouveau 0000:01:00.0: Allocating FIFO number 0
[   15.975138] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc:
initialised FIFO 0
[   15.975160] [drm] nouveau 0000:01:00.0: Initial CRTC_OWNER is 0
[   15.975173] [drm] nouveau 0000:01:00.0: Saving VGA fonts
[   16.031949] type=1400 audit(1290758385.162:10): apparmor="STATUS"
operation="profile_load" name="/usr/bin/evince-previewer" pid=917
comm="apparmor_parser"
[   16.078981] type=1400 audit(1290758385.210:11): apparmor="STATUS"
operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=917
comm="apparmor_parser"
[   16.117521] b43-phy0: Loading firmware version 410.2160 (2007-05-26
15:32:10)
[   16.149942] [drm] nouveau 0000:01:00.0: Probing TV encoders on I2C
bus: 1
[   16.150869] [drm] nouveau 0000:01:00.0: Detected TV encoder: ch7006
[   16.190965] ch7006 1-0075: Detected version ID: 50
[   16.198806] [drm] nouveau 0000:01:00.0: Detected a VGA connector
[   16.199348] [drm] nouveau 0000:01:00.0: Detected a TV connector
[   16.210086] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   16.372589] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga
encoder (output 0)
[   16.372599] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV
encoder (output 1)
[   16.916856] [drm] nouveau 0000:01:00.0: allocated 1440x900 fb:
0x49000, bo f47ec800
[   16.993377] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV
encoder (output 1)
[   17.003573] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga
encoder (output 0)
[   17.003581] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on
CRTC 0 using output @
[   17.012339] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV
encoder (output 1)
[   17.012360] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV
encoder (output 1)
[   17.023110] Console: switching to colour frame buffer device 180x56
[   17.027112] fb0: nouveaufb frame buffer device
[   17.027117] drm: registered panic notifier
[   17.032174] Slow work thread pool: Starting up
[   17.032293] Slow work thread pool: Ready
[   17.032313] [drm] Initialized nouveau 0.0.16 20090420 for
0000:01:00.0 on minor 0
[   20.953556] ADDRCONF(NETDEV_UP): wlan3: link is not ready
[   20.972974] eth0: link down
[   20.973348] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.009359] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1
[   22.010332] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc:
initialised FIFO 1
[   29.783390] EXT4-fs (sda1): re-mounted. Opts:
errors=remount-ro,commit=0
[   35.526477] slamr: module license 'Smart Link Ltd.' taints kernel.
[   35.526487] Disabling lock debugging due to kernel taint
[   35.553152] slamr: SmartLink AMRMO modem.
[   46.635240] wlan0: authenticate with 00:80:5a:28:6e:0e (try 1)
[   46.636687] wlan0: authenticated
[   46.638558] wlan0: associate with 00:80:5a:28:6e:0e (try 1)
[   46.640566] wlan0: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=1)
[   46.640575] wlan0: associated
[   46.642025] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   52.832089] ata4: lost interrupt (Status 0x58)
[   52.832139] ata4: drained 24 bytes to clear DRQ.
[   52.832155] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6
frozen
[   52.832169] sr 3:0:0:0: CDB: Xdread, Read track info: 52 01 00 00 00
01 00 00 20 00
[   52.832197] ata4.00: cmd a0/01:00:00:20:00/00:00:00:00:00/a0 tag 0
dma 16416 in
[   52.832200]          res 40/00:02:00:08:00/00:00:00:00:00/a0 Emask
0x4 (timeout)
[   52.832206] ata4.00: status: { DRDY }
[   52.888083] ata4: soft resetting link
[   53.044273] ata4.01: NODEV after polling detection
[   53.044281] ata4.01: revalidation failed (errno=-2)
[   57.640046] wlan0: no IPv6 routers present
[   58.044094] ata4: soft resetting link
[   58.200215] ata4.01: NODEV after polling detection
[   58.200223] ata4.01: revalidation failed (errno=-2)
[   59.784060] cfg80211: Found new beacon on frequency: 2467 MHz (Ch 12)
on phy1
[   60.505317] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[   60.507426] wlan3: authenticated
[   60.577290] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[   60.653917] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[   60.653928] wlan3: associated
[   60.729725] ADDRCONF(NETDEV_CHANGE): wlan3: link becomes ready
[   63.200071] ata4: soft resetting link
[   63.356223] ata4.01: NODEV after polling detection
[   63.356231] ata4.01: revalidation failed (errno=-2)
[   63.356239] ata4.01: disabled
[   63.356250] ata4.00: failed to IDENTIFY (I/O error, err_mask=0x40)
[   63.356255] ata4.00: revalidation failed (errno=-5)
[   68.356063] ata4: soft resetting link
[   68.536373] ata4.00: configured for UDMA/33
[   68.538669] ata4: EH complete
[   70.896012] wlan3: no IPv6 routers present
[   71.461218] ISO 9660 Extensions: Microsoft Joliet Level 1
[   71.547826] ISOFS: changing to secondary root
[   72.599097] ISO 9660 Extensions: Microsoft Joliet Level 1
[   72.628085] ISOFS: changing to secondary root
[   87.332052] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[  107.382765] wlan0: authenticate with 00:80:5a:28:6e:0e (try 1)
[  107.580087] wlan0: authenticate with 00:80:5a:28:6e:0e (try 2)
[  107.581529] wlan0: authenticated
[  107.581907] wlan0: associate with 00:80:5a:28:6e:0e (try 1)
[  107.598793] wlan0: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=1)
[  107.598802] wlan0: associated
[  352.548031] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[  355.169335] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[  355.368041] wlan3: authenticate with 00:80:5a:28:6e:0e (try 2)
[  355.568033] wlan3: authenticate with 00:80:5a:28:6e:0e (try 3)
[  355.768032] wlan3: authentication with 00:80:5a:28:6e:0e timed out
[  367.465326] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  367.664029] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  367.864473] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  368.064036] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  370.573440] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  370.772039] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  370.972035] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  371.172058] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  382.889436] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  383.088034] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  383.288040] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  383.488242] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  390.564040] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[  390.564883] cfg80211: All devices are disconnected, going to restore
regulatory settings
[  390.564894] cfg80211: Restoring regulatory settings
[  390.564901] cfg80211: Calling CRDA to update world regulatory domain
[  390.583824] cfg80211: World regulatory domain updated:
[  390.583833]     (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[  390.583841]     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[  390.583847]     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[  390.583853]     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi,
2000 mBm)
[  390.583859]     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[  390.583865]     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi,
2000 mBm)
[  391.970389] wlan0: authenticate with 00:80:5a:28:6e:0e (try 1)
[  392.169050] wlan0: authenticate with 00:80:5a:28:6e:0e (try 2)
[  392.368055] wlan0: authenticate with 00:80:5a:28:6e:0e (try 3)
[  392.568068] wlan0: authentication with 00:80:5a:28:6e:0e timed out
[  395.213284] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  395.412171] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  395.612036] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  395.812040] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  407.601244] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  407.800044] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  408.000047] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  408.200048] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  409.563599] wlan0: direct probe to 00:80:5a:28:6e:0e (try 1)
[  409.760062] wlan0: direct probe to 00:80:5a:28:6e:0e (try 2)
[  409.960050] wlan0: direct probe to 00:80:5a:28:6e:0e (try 3)
[  410.160032] wlan0: direct probe to 00:80:5a:28:6e:0e timed out
[  420.011084] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  420.208087] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  420.409443] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  420.609257] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  427.180006] wlan0: direct probe to 00:80:5a:28:6e:0e (try 1)
[  427.380081] wlan0: direct probe to 00:80:5a:28:6e:0e (try 2)
[  427.580178] wlan0: direct probe to 00:80:5a:28:6e:0e (try 3)
[  427.780082] wlan0: direct probe to 00:80:5a:28:6e:0e timed out
[  443.466153] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  443.664080] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  443.864078] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  444.064071] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  451.115366] wlan0: direct probe to 00:80:5a:28:6e:0e (try 1)
[  451.312079] wlan0: direct probe to 00:80:5a:28:6e:0e (try 2)
[  451.512086] wlan0: direct probe to 00:80:5a:28:6e:0e (try 3)
[  451.712049] wlan0: direct probe to 00:80:5a:28:6e:0e timed out
[  455.842272] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  456.040070] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  456.240646] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  456.441885] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  468.281329] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  468.480313] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  468.680101] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  468.880113] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  480.705338] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  480.904081] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  481.104110] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  481.304090] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  484.266996] wlan0: authenticate with 00:24:d1:16:a7:25 (try 1)
[  484.269012] wlan0: authenticated
[  484.269217] wlan0: associate with 00:24:d1:16:a7:25 (try 1)
[  484.271483] wlan0: RX AssocResp from 00:24:d1:16:a7:25 (capab=0x411
status=0 aid=1)
[  484.271492] wlan0: associated
[  493.116077] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[  493.316070] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[  493.516076] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[  493.716081] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[  499.897864] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  501.044340] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  501.765444] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  503.018257] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  504.723050] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  505.215408] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  506.805357] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  508.263459] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  517.037333] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[  517.043827] wlan3: authenticated
[  517.113347] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[  517.186862] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[  517.186873] wlan3: associated
[  924.781371] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  960.815473] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  961.595176] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  961.851799] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[  963.182548] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[  963.882184] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[  984.612035] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[  987.282016] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[  987.480047] wlan3: authenticate with 00:80:5a:28:6e:0e (try 2)
[  987.482227] wlan3: authenticated
[  987.549248] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[  987.619266] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[  987.619277] wlan3: associated
[ 1052.580090] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[ 1055.253290] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 1055.452037] wlan3: authenticate with 00:80:5a:28:6e:0e (try 2)
[ 1055.652037] wlan3: authenticate with 00:80:5a:28:6e:0e (try 3)
[ 1055.852026] wlan3: authentication with 00:80:5a:28:6e:0e timed out
[ 1067.613318] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 1067.812078] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 1068.012064] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 1068.212074] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 1070.721360] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 1070.920045] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 1070.921785] wlan3: direct probe responded
[ 1070.921807] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 1070.924439] wlan3: authenticated
[ 1070.997292] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[ 1071.067331] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[ 1071.067343] wlan3: associated
[ 1135.524026] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[ 1138.197299] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 1138.198807] wlan3: authenticated
[ 1138.269275] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[ 1138.338882] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[ 1138.338891] wlan3: associated
[ 1168.200236] show_signal_msg: 9 callbacks suppressed
[ 1168.200249] gs[6547]: segfault at 8 ip 00272c67 sp bfc225f0 error 4
in libtiff.so.4.3.3[26e000+57000]
[ 1171.556051] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[ 1174.225265] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 1174.424037] wlan3: authenticate with 00:80:5a:28:6e:0e (try 2)
[ 1174.624033] wlan3: authenticate with 00:80:5a:28:6e:0e (try 3)
[ 1174.824035] wlan3: authentication with 00:80:5a:28:6e:0e timed out
[ 1186.577240] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 1186.776038] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 1186.976070] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 1187.176028] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 1189.693350] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 1189.892051] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 1190.092031] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 1190.292042] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 1202.105706] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 1202.107820] wlan3: authenticated
[ 1202.181282] wlan3: associate with 00:80:5a:28:6e:0e (try 1)
[ 1202.380044] wlan3: associate with 00:80:5a:28:6e:0e (try 2)
[ 1202.382344] wlan3: RX AssocResp from 00:80:5a:28:6e:0e (capab=0x431
status=0 aid=2)
[ 1202.382352] wlan3: associated
[ 2303.485359] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 2303.721466] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 2304.334881] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[ 2306.230645] process `sysctl' is using deprecated sysctl (syscall)
net.ipv6.neigh.default.retrans_time; Use
net.ipv6.neigh.default.retrans_time_ms instead.
[ 2320.548027] No probe response from AP 00:80:5a:28:6e:0e after 500ms,
disconnecting.
[ 2323.214144] wlan3: authenticate with 00:80:5a:28:6e:0e (try 1)
[ 2323.412034] wlan3: authenticate with 00:80:5a:28:6e:0e (try 2)
[ 2323.612028] wlan3: authenticate with 00:80:5a:28:6e:0e (try 3)
[ 2323.812027] wlan3: authentication with 00:80:5a:28:6e:0e timed out
[ 2335.581731] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2335.780031] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2335.980037] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2336.180085] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2338.705313] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2338.904050] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2339.104072] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2339.304083] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2351.109477] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2351.308031] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2351.508044] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2351.708038] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2363.485259] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2363.684043] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2363.884062] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2364.084041] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2375.853316] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2376.052050] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2376.252030] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2376.452040] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2388.245325] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2388.444032] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2388.644032] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2388.844032] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2405.629307] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2405.828033] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2406.028043] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2406.228042] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2417.997338] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2418.196031] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2418.396041] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2418.596041] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2430.385248] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2430.584030] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2430.784038] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2430.984041] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2442.801298] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2443.000124] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2443.200037] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2443.400041] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 2455.169583] wlan3: direct probe to 00:80:5a:28:6e:0e (try 1)
[ 2455.368073] wlan3: direct probe to 00:80:5a:28:6e:0e (try 2)
[ 2455.568039] wlan3: direct probe to 00:80:5a:28:6e:0e (try 3)
[ 2455.768028] wlan3: direct probe to 00:80:5a:28:6e:0e timed out
[ 3607.929090] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 3646.336789] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 3646.973085] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[ 3984.717732] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 4021.495374] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 4022.162141] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)
[ 4022.446913] hcfpcihw 0000:00:0c.0: PCI INT A disabled
[ 4023.825258] hcfpcihw 0000:00:0c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
[ 4024.632717] ttySHCF0 at I/O 0xc000 (irq = 16) is a Conexant HCF
controllerless PCI modem (PCI-14f1:1033-1092:0ac8)

Module                  Size  Used by
hcfpcihw                4979  0
hcfpciserial           18627  1 hcfpcihw
hcfpciengine          945480  2 hcfpcihw,hcfpciserial
hcfpciosspec           58895  3 hcfpciserial,hcfpciengine
nls_utf8                1069  1
isofs                  30022  1
binfmt_misc             6599  1
slamr                 420449  0
ungrab_winmodem         1003  0
ch7006                 16545  1
snd_ens1371            18782  2
nouveau               516971  2
snd_usb_audio          86704  2
snd_ac97_codec         99227  1 snd_ens1371
ac97_bus                1014  1 snd_ac97_codec
snd_pcm                71475  3 snd_ens1371,snd_ac97_codec,snd_usb_audio
arc4                    1165  4
snd_hwdep               5040  1 snd_usb_audio
snd_usbmidi_lib        17413  1 snd_usb_audio
snd_seq_midi            4588  0
ttm                    56633  1 nouveau
rtl8187                51470  0
b43                   168681  0
snd_rawmidi            17783  3 snd_ens1371,snd_usbmidi_lib,snd_seq_midi
drm_kms_helper         30200  2 ch7006,nouveau
snd_seq_midi_event      6047  1 snd_seq_midi
mac80211              231541  2 rtl8187,b43
snd_seq                47174  2 snd_seq_midi,snd_seq_midi_event
ppdev                   5556  0
snd_timer              19067  2 snd_pcm,snd_seq
snd_seq_device          5744  3 snd_seq_midi,snd_rawmidi,snd_seq
drm                   168054  5 ch7006,nouveau,ttm,drm_kms_helper
ns558                   3068  0
cfg80211              144470  3 rtl8187,b43,mac80211
parport_pc             26058  1
eeprom_93cx6            1345  1 rtl8187
gameport                9327  3 snd_ens1371,ns558
i2c_viapro              5777  0
via_agp                 5322  1
snd                    49006  18
snd_ens1371,snd_ac97_codec,snd_usb_audio,snd_pcm,snd_hwdep,snd_usbmidi_lib,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_algo_bit            5168  1 nouveau
soundcore                880  1 snd
led_class               2633  2 rtl8187,b43
snd_page_alloc          7120  1 snd_pcm
shpchp                 29886  0
agpgart                32011  3 ttm,drm,via_agp
lp                      7342  0
parport                31492  3 ppdev,parport_pc,lp
8139too                19581  0
usbhid                 36882  0
hid                    67742  1 usbhid
usb_storage            40172  0
via_rhine              19038  0
pata_via                7300  1
8139cp                 16934  0
sata_via                7344  2
ssb                    39288  1 b43
floppy                 54311  0
mii                     4425  3 8139too,via_rhine,8139cp






[Linux DVB]     [Asterisk]     [Photo]     [DCCP]     [Netdev]     [Xorg]     [Xfree86]     [Fedora Women]     [Linux USB]

Powered by Linux