[PATCH 1/3] drivers/misc: add support for BMP18x pressure sensors

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


This driver adds support for Bosch Sensortec's pressure sensors
BMP085 and BMP18x.

The driver is based on the bmp085 driver by Christoph Mair
and uses the same sysfs interface.

Tested-by: Zhengguang Guo <zhengguang.guo@xxxxxxxxxxxxxxxxxxx>
Reviewed-by: Stefan Nilsson <stefan.nilsson@xxxxxxxxxxxxx>
Signed-off-by: Eric Andersson <eric.andersson@xxxxxxxxxxxxx>
---
 drivers/misc/Kconfig       |   30 +++
 drivers/misc/Makefile      |    3 +
 drivers/misc/bmp18x-core.c |  502 ++++++++++++++++++++++++++++++++++++++++++++
 drivers/misc/bmp18x-i2c.c  |  121 +++++++++++
 drivers/misc/bmp18x-spi.c  |  143 +++++++++++++
 include/linux/i2c/bmp18x.h |   65 ++++++
 6 files changed, 864 insertions(+), 0 deletions(-)
 create mode 100644 drivers/misc/bmp18x-core.c
 create mode 100644 drivers/misc/bmp18x-i2c.c
 create mode 100644 drivers/misc/bmp18x-spi.c
 create mode 100644 include/linux/i2c/bmp18x.h

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index c779509..2e894fd 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -498,6 +498,36 @@ config MAX8997_MUIC
 	  Maxim MAX8997 PMIC.
 	  The MAX8997 MUIC is a USB port accessory detector and switch.
 
+config BMP18X
+        tristate "BMP18X digital pressure sensor"
+        depends on (I2C || SPI_MASTER) && SYSFS
+        help
+          Say Y here if you want support for Bosch Sensortec's digital
+	  pressure sensors BMP085 and BMP18x.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bmp18x-core.
+
+config BMP18X_I2C
+        tristate "support I2C bus connection"
+        depends on BMP18X && I2C
+        help
+          Say Y here if you want to support Bosch Sensortec's digital pressure
+          sensor hooked to an I2C bus.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bmp18x-i2c.
+
+config BMP18X_SPI
+        tristate "support SPI bus connection"
+        depends on BMP18X && SPI_MASTER
+        help
+          Say Y here if you want to support Bosch Sensortec's digital pressure
+          sensor hooked to a SPI bus.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bmp18x-spi.
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 3e1d801..a1aa04a 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -11,6 +11,9 @@ obj-$(CONFIG_ATMEL_PWM)		+= atmel_pwm.o
 obj-$(CONFIG_ATMEL_SSC)		+= atmel-ssc.o
 obj-$(CONFIG_ATMEL_TCLIB)	+= atmel_tclib.o
 obj-$(CONFIG_BMP085)		+= bmp085.o
+obj-$(CONFIG_BMP18X)		+= bmp18x-core.o
+obj-$(CONFIG_BMP18X_I2C)	+= bmp18x-i2c.o
+obj-$(CONFIG_BMP18X_SPI)	+= bmp18x-spi.o
 obj-$(CONFIG_ICS932S401)	+= ics932s401.o
 obj-$(CONFIG_LKDTM)		+= lkdtm.o
 obj-$(CONFIG_TIFM_CORE)       	+= tifm_core.o
diff --git a/drivers/misc/bmp18x-core.c b/drivers/misc/bmp18x-core.c
new file mode 100644
index 0000000..62ab8ca
--- /dev/null
+++ b/drivers/misc/bmp18x-core.c
@@ -0,0 +1,502 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * Based on:
+ * BMP085 driver, bmp085.c
+ * Copyright (c) 2010  Christoph Mair <christoph.mair@xxxxxxxxx>
+ *
+ * This driver supports the bmp18x digital barometric pressure
+ * and temperature sensors from Bosch Sensortec. The datasheet
+ * is available from their website:
+ * http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP180-DS000-07.pdf
+ *
+ * A pressure measurement is issued by reading from pressure0_input.
+ * The return value ranges from 30000 to 110000 pascal with a resulution
+ * of 1 pascal (0.01 millibar) which enables measurements from 9000m above
+ * to 500m below sea level.
+ *
+ * The temperature can be read from temp0_input. Values range from
+ * -400 to 850 representing the ambient temperature in degree celsius
+ * multiplied by 10.The resolution is 0.1 celsius.
+ *
+ * Because ambient pressure is temperature dependent, a temperature
+ * measurement will be executed automatically even if the user is reading
+ * from pressure0_input. This happens if the last temperature measurement
+ * has been executed more then one second ago.
+ *
+ * To decrease RMS noise from pressure measurements, the bmp18x can
+ * autonomously calculate the average of up to eight samples. This is
+ * set up by writing to the oversampling sysfs file. Accepted values
+ * are 0, 1, 2 and 3. 2^x when x is the value written to this file
+ * specifies the number of samples used to calculate the ambient pressure.
+ * RMS noise is specified with six pascal (without averaging) and decreases
+ * down to 3 pascal when using an oversampling setting of 3.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/i2c/bmp18x.h>
+
+#define BMP18X_CHIP_ID			0x55
+
+#define BMP18X_CALIBRATION_DATA_START	0xAA
+#define BMP18X_CALIBRATION_DATA_LENGTH	11	/* 16 bit values */
+#define BMP18X_CHIP_ID_REG		0xD0
+#define BMP18X_CTRL_REG			0xF4
+#define BMP18X_TEMP_MEASUREMENT		0x2E
+#define BMP18X_PRESSURE_MEASUREMENT	0x34
+#define BMP18X_CONVERSION_REGISTER_MSB	0xF6
+#define BMP18X_CONVERSION_REGISTER_LSB	0xF7
+#define BMP18X_CONVERSION_REGISTER_XLSB	0xF8
+#define BMP18X_TEMP_CONVERSION_TIME	5
+
+struct bmp18x_calibration_data {
+	s16 AC1, AC2, AC3;
+	u16 AC4, AC5, AC6;
+	s16 B1, B2;
+	s16 MB, MC, MD;
+};
+
+struct bmp18x_data {
+	struct	bmp18x_data_bus data_bus;
+	struct	device *dev;
+	struct	mutex lock;
+	struct	bmp18x_calibration_data calibration;
+	u8	oversampling_setting;
+	u32	raw_temperature;
+	u32	raw_pressure;
+	u32	temp_measurement_period;
+	u32	last_temp_measurement;
+	s32	b6; /* calculated temperature correction coefficient */
+};
+
+static inline int bmp18x_read_block(struct bmp18x_data *data, u8 reg, int len,
+				    char *buf)
+{
+	return data->data_bus.bops->read_block(data->data_bus.client, reg,
+					       len, buf);
+}
+
+static inline int bmp18x_read_byte(struct bmp18x_data *data, u8 reg)
+{
+	return data->data_bus.bops->read_byte(data->data_bus.client, reg);
+}
+
+static inline int bmp18x_write_byte(struct bmp18x_data *data, u8 reg, u8 value)
+{
+	return data->data_bus.bops->write_byte(data->data_bus.client, reg,
+					       value);
+}
+
+static s32 bmp18x_read_calibration_data(struct bmp18x_data *data)
+{
+	u16 tmp[BMP18X_CALIBRATION_DATA_LENGTH];
+	struct bmp18x_calibration_data *cali = &(data->calibration);
+	s32 status = bmp18x_read_block(data, BMP18X_CALIBRATION_DATA_START,
+				(BMP18X_CALIBRATION_DATA_LENGTH << 1),
+				(u8 *)tmp);
+	if (status < 0)
+		return status;
+
+	if (status != (BMP18X_CALIBRATION_DATA_LENGTH << 1))
+		return -EIO;
+
+	cali->AC1 =  be16_to_cpu(tmp[0]);
+	cali->AC2 =  be16_to_cpu(tmp[1]);
+	cali->AC3 =  be16_to_cpu(tmp[2]);
+	cali->AC4 =  be16_to_cpu(tmp[3]);
+	cali->AC5 =  be16_to_cpu(tmp[4]);
+	cali->AC6 = be16_to_cpu(tmp[5]);
+	cali->B1 = be16_to_cpu(tmp[6]);
+	cali->B2 = be16_to_cpu(tmp[7]);
+	cali->MB = be16_to_cpu(tmp[8]);
+	cali->MC = be16_to_cpu(tmp[9]);
+	cali->MD = be16_to_cpu(tmp[10]);
+	return 0;
+}
+
+static s32 bmp18x_update_raw_temperature(struct bmp18x_data *data)
+{
+	u16 tmp;
+	s32 status;
+
+	mutex_lock(&data->lock);
+	status = bmp18x_write_byte(data, BMP18X_CTRL_REG,
+				   BMP18X_TEMP_MEASUREMENT);
+	if (status < 0) {
+		dev_err(data->dev,
+			"Error while requesting temperature measurement.\n");
+		goto exit;
+	}
+	msleep(BMP18X_TEMP_CONVERSION_TIME);
+
+	status = bmp18x_read_block(data, BMP18X_CONVERSION_REGISTER_MSB,
+				   sizeof(tmp), (u8 *)&tmp);
+	if (status < 0)
+		goto exit;
+	if (status != sizeof(tmp)) {
+		dev_err(data->dev,
+			"Error while reading temperature measurement result\n");
+		status = -EIO;
+		goto exit;
+	}
+	data->raw_temperature = be16_to_cpu(tmp);
+	data->last_temp_measurement = jiffies;
+	status = 0;	/* everything ok, return 0 */
+
+exit:
+	mutex_unlock(&data->lock);
+	return status;
+}
+
+static s32 bmp18x_update_raw_pressure(struct bmp18x_data *data)
+{
+	u32 tmp = 0;
+	s32 status;
+
+	mutex_lock(&data->lock);
+	status = bmp18x_write_byte(data, BMP18X_CTRL_REG,
+			BMP18X_PRESSURE_MEASUREMENT +
+			(data->oversampling_setting << 6));
+	if (status < 0) {
+		dev_err(data->dev,
+			"Error while requesting pressure measurement.\n");
+		goto exit;
+	}
+
+	/* wait for the end of conversion */
+	msleep(2+(3 << data->oversampling_setting));
+
+	/* copy data into a u32 (4 bytes), but skip the first byte. */
+	status = bmp18x_read_block(data, BMP18X_CONVERSION_REGISTER_MSB, 3,
+				   ((u8 *)&tmp)+1);
+	if (status < 0)
+		goto exit;
+	if (status != 3) {
+		dev_err(data->dev,
+			"Error while reading pressure measurement results\n");
+		status = -EIO;
+		goto exit;
+	}
+	data->raw_pressure = be32_to_cpu((tmp));
+	data->raw_pressure >>= (8-data->oversampling_setting);
+	status = 0;	/* everything ok, return 0 */
+
+exit:
+	mutex_unlock(&data->lock);
+	return status;
+}
+
+/*
+ * This function starts the temperature measurement and returns the value
+ * in tenth of a degree celsius.
+ */
+static s32 bmp18x_get_temperature(struct bmp18x_data *data, int *temperature)
+{
+	struct bmp18x_calibration_data *cali = &data->calibration;
+	long x1, x2;
+	int status;
+
+	status = bmp18x_update_raw_temperature(data);
+	if (status < 0)
+		goto exit;
+
+	x1 = ((data->raw_temperature - cali->AC6) * cali->AC5) >> 15;
+	x2 = (cali->MC << 11) / (x1 + cali->MD);
+	data->b6 = x1 + x2 - 4000;
+	/* if NULL just update b6. Used for pressure only measurements */
+	if (temperature != NULL)
+		*temperature = (x1+x2+8) >> 4;
+
+exit:
+	return status;
+}
+
+/*
+ * This function starts the pressure measurement and returns the value
+ * in millibar. Since the pressure depends on the ambient temperature,
+ * a temperature measurement is executed according to the given temperature
+ * measurememt period (default is 1 sec boundary). This period could vary
+ * and needs to be adjusted according to the sensor environment, i.e. if big
+ * temperature variations then the temperature needs to be read out often.
+ */
+static s32 bmp18x_get_pressure(struct bmp18x_data *data, int *pressure)
+{
+	struct bmp18x_calibration_data *cali = &data->calibration;
+	s32 x1, x2, x3, b3;
+	u32 b4, b7;
+	s32 p;
+	int status;
+
+	/* update the ambient temperature according to the given meas. period */
+	if (data->last_temp_measurement +
+			data->temp_measurement_period < jiffies) {
+		status = bmp18x_get_temperature(data, NULL);
+		if (status < 0)
+			return status;
+	}
+
+	status = bmp18x_update_raw_pressure(data);
+	if (status < 0)
+		return status;
+
+	x1 = (data->b6 * data->b6) >> 12;
+	x1 *= cali->B2;
+	x1 >>= 11;
+
+	x2 = cali->AC2 * data->b6;
+	x2 >>= 11;
+
+	x3 = x1 + x2;
+
+	b3 = (((((s32)cali->AC1) * 4 + x3) << data->oversampling_setting) + 2);
+	b3 >>= 2;
+
+	x1 = (cali->AC3 * data->b6) >> 13;
+	x2 = (cali->B1 * ((data->b6 * data->b6) >> 12)) >> 16;
+	x3 = (x1 + x2 + 2) >> 2;
+	b4 = (cali->AC4 * (u32)(x3 + 32768)) >> 15;
+
+	b7 = ((u32)data->raw_pressure - b3) *
+					(50000 >> data->oversampling_setting);
+	p = ((b7 < 0x80000000) ? ((b7 << 1) / b4) : ((b7 / b4) * 2));
+
+	x1 = p >> 8;
+	x1 *= x1;
+	x1 = (x1 * 3038) >> 16;
+	x2 = (-7357 * p) >> 16;
+	p += (x1 + x2 + 3791) >> 4;
+
+	*pressure = p;
+
+	return 0;
+}
+
+/*
+ * This function sets the chip-internal oversampling. Valid values are 0..3.
+ * The chip will use 2^oversampling samples for internal averaging.
+ * This influences the measurement time and the accuracy; larger values
+ * increase both. The datasheet gives an overview on how measurement time,
+ * accuracy and noise correlate.
+ */
+static void bmp18x_set_oversampling(struct bmp18x_data *data,
+						unsigned char oversampling)
+{
+	if (oversampling > 3)
+		oversampling = 3;
+	data->oversampling_setting = oversampling;
+}
+
+/*
+ * Returns the currently selected oversampling. Range: 0..3
+ */
+static unsigned char bmp18x_get_oversampling(struct bmp18x_data *data)
+{
+	return data->oversampling_setting;
+}
+
+/* sysfs callbacks */
+static ssize_t set_oversampling(struct device *dev,
+				struct device_attribute *attr,
+				const char *buf, size_t count)
+{
+	struct bmp18x_data *data = dev_get_drvdata(dev);
+	unsigned long oversampling;
+	int err = kstrtoul(buf, 10, &oversampling);
+
+	if (err == 0) {
+		mutex_lock(&data->lock);
+		bmp18x_set_oversampling(data, oversampling);
+		mutex_unlock(&data->lock);
+		return count;
+	}
+
+	return err;
+}
+
+static ssize_t show_oversampling(struct device *dev,
+				 struct device_attribute *attr, char *buf)
+{
+	struct bmp18x_data *data = dev_get_drvdata(dev);
+
+	return sprintf(buf, "%u\n", bmp18x_get_oversampling(data));
+}
+static DEVICE_ATTR(oversampling, S_IWUSR | S_IRUGO,
+					show_oversampling, set_oversampling);
+
+
+static ssize_t show_temperature(struct device *dev,
+				struct device_attribute *attr, char *buf)
+{
+	int temperature;
+	int status;
+	struct bmp18x_data *data = dev_get_drvdata(dev);
+
+	status = bmp18x_get_temperature(data, &temperature);
+	if (status < 0)
+		return status;
+	else
+		return sprintf(buf, "%d\n", temperature);
+}
+static DEVICE_ATTR(temp0_input, S_IRUGO, show_temperature, NULL);
+
+
+static ssize_t show_pressure(struct device *dev,
+			     struct device_attribute *attr, char *buf)
+{
+	int pressure;
+	int status;
+	struct bmp18x_data *data = dev_get_drvdata(dev);
+
+	status = bmp18x_get_pressure(data, &pressure);
+	if (status < 0)
+		return status;
+	else
+		return sprintf(buf, "%d\n", pressure);
+}
+static DEVICE_ATTR(pressure0_input, S_IRUGO, show_pressure, NULL);
+
+
+static struct attribute *bmp18x_attributes[] = {
+	&dev_attr_temp0_input.attr,
+	&dev_attr_pressure0_input.attr,
+	&dev_attr_oversampling.attr,
+	NULL
+};
+
+static const struct attribute_group bmp18x_attr_group = {
+	.attrs = bmp18x_attributes,
+};
+
+static int bmp18x_init_client(struct bmp18x_data *data,
+			      struct bmp18x_platform_data *pdata)
+{
+	int status = bmp18x_read_calibration_data(data);
+
+	if (status < 0)
+		return status;
+
+	data->last_temp_measurement = 0;
+	data->temp_measurement_period =
+		pdata ? (pdata->temp_measurement_period/1000)*HZ : 1*HZ;
+	data->oversampling_setting = pdata ? pdata->default_oversampling : 3;
+	mutex_init(&data->lock);
+
+	return 0;
+}
+
+__devinit int bmp18x_probe(struct device *dev, struct bmp18x_data_bus *data_bus)
+{
+	struct bmp18x_data *data;
+	struct bmp18x_platform_data *pdata = dev->platform_data;
+	u8 chip_id = (pdata && pdata->chip_id) ? pdata->chip_id : BMP18X_CHIP_ID;
+	int err = 0;
+
+	if (pdata && pdata->init_hw) {
+		err = pdata->init_hw();
+		if (err) {
+			dev_err(dev, "%s: init_hw failed!\n",
+				BMP18X_NAME);
+			return err;
+		}
+	}
+
+	data = kzalloc(sizeof(struct bmp18x_data), GFP_KERNEL);
+	if (!data) {
+		err = -ENOMEM;
+		goto exit;
+	}
+
+	dev_set_drvdata(dev, data);
+	data->data_bus = *data_bus;
+	data->dev = dev;
+
+	if (bmp18x_read_byte(data, BMP18X_CHIP_ID_REG) != chip_id) {
+		dev_err(dev, "%s: chip_id failed!\n", BMP18X_NAME);
+		err = -ENODEV;
+		goto exit_free;
+	}
+
+	/* Initialize the BMP18X chip */
+	err = bmp18x_init_client(data, pdata);
+	if (err < 0)
+		goto exit_free;
+
+	/* Register sysfs hooks */
+	err = sysfs_create_group(&dev->kobj, &bmp18x_attr_group);
+	if (err)
+		goto exit_free;
+
+	dev_info(dev, "Succesfully initialized bmp18x!\n");
+	return 0;
+
+exit_free:
+	kfree(data);
+exit:
+	if (pdata && pdata->deinit_hw)
+		pdata->deinit_hw();
+	return err;
+}
+EXPORT_SYMBOL(bmp18x_probe);
+
+int bmp18x_remove(struct device *dev)
+{
+	struct bmp18x_data *data = dev_get_drvdata(dev);
+	struct bmp18x_platform_data *pdata = dev->platform_data;
+
+	sysfs_remove_group(&dev->kobj, &bmp18x_attr_group);
+
+	if (pdata && pdata->deinit_hw)
+		pdata->deinit_hw();
+
+	kfree(data);
+
+	return 0;
+}
+EXPORT_SYMBOL(bmp18x_remove);
+
+#ifdef CONFIG_PM
+int bmp18x_disable(struct device *dev)
+{
+	struct bmp18x_platform_data *pdata = dev->platform_data;
+
+	if (pdata && pdata->deinit_hw)
+		pdata->deinit_hw();
+
+	return 0;
+}
+EXPORT_SYMBOL(bmp18x_disable);
+
+int bmp18x_enable(struct device *dev)
+{
+	struct bmp18x_platform_data *pdata = dev->platform_data;
+
+	if (pdata && pdata->init_hw)
+		return pdata->init_hw();
+
+	return 0;
+}
+EXPORT_SYMBOL(bmp18x_enable);
+#endif
+
+MODULE_AUTHOR("Eric Andersson <eric.andersson@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("BMP18X driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/misc/bmp18x-i2c.c b/drivers/misc/bmp18x-i2c.c
new file mode 100644
index 0000000..b7d7ade
--- /dev/null
+++ b/drivers/misc/bmp18x-i2c.c
@@ -0,0 +1,121 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * Based on:
+ * BMP085 driver, bmp085.c
+ * Copyright (c) 2010  Christoph Mair <christoph.mair@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/i2c/bmp18x.h>
+
+static int bmp18x_i2c_read_block(void *client, u8 reg, int len, char *buf)
+{
+	return i2c_smbus_read_i2c_block_data(client, reg, len, buf);
+}
+
+static int bmp18x_i2c_read_byte(void *client, u8 reg)
+{
+	return i2c_smbus_read_byte_data(client, reg);
+}
+
+static int bmp18x_i2c_write_byte(void *client, u8 reg, u8 value)
+{
+	return i2c_smbus_write_byte_data(client, reg, value);
+}
+
+static const struct bmp18x_bus_ops bmp18x_i2c_bus_ops = {
+	.read_block	= bmp18x_i2c_read_block,
+	.read_byte	= bmp18x_i2c_read_byte,
+	.write_byte	= bmp18x_i2c_write_byte
+};
+
+static int __devinit bmp18x_i2c_probe(struct i2c_client *client,
+				      const struct i2c_device_id *id)
+{
+	struct bmp18x_data_bus data_bus = {
+		.bops = &bmp18x_i2c_bus_ops,
+		.client = client
+	};
+
+	return bmp18x_probe(&client->dev, &data_bus);
+}
+
+static void bmp18x_i2c_shutdown(struct i2c_client *client)
+{
+	bmp18x_disable(&client->dev);
+}
+
+static int bmp18x_i2c_remove(struct i2c_client *client)
+{
+	return bmp18x_remove(&client->dev);
+}
+
+#ifdef CONFIG_PM
+static int bmp18x_i2c_suspend(struct device *dev)
+{
+	return bmp18x_disable(dev);
+}
+
+static int bmp18x_i2c_resume(struct device *dev)
+{
+	return bmp18x_enable(dev);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(bmp18x_i2c_pm_ops, bmp18x_i2c_suspend,
+			 bmp18x_i2c_resume);
+
+static const struct i2c_device_id bmp18x_id[] = {
+	{ BMP18X_NAME, 0 },
+	{ "bmp085", 0 },
+	{ "bmp180", 0 },
+	{ "bmp181", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, bmp18x_id);
+
+static struct i2c_driver bmp18x_i2c_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= BMP18X_NAME,
+		.pm	= &bmp18x_i2c_pm_ops,
+	},
+	.id_table	= bmp18x_id,
+	.probe		= bmp18x_i2c_probe,
+	.shutdown	= bmp18x_i2c_shutdown,
+	.remove		= __devexit_p(bmp18x_i2c_remove)
+};
+
+static int __init bmp18x_i2c_init(void)
+{
+	return i2c_add_driver(&bmp18x_i2c_driver);
+}
+
+static void __exit bmp18x_i2c_exit(void)
+{
+	i2c_del_driver(&bmp18x_i2c_driver);
+}
+
+MODULE_AUTHOR("Eric Andersson <eric.andersson@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("BMP18X I2C bus driver");
+MODULE_LICENSE("GPL");
+
+module_init(bmp18x_i2c_init);
+module_exit(bmp18x_i2c_exit);
diff --git a/drivers/misc/bmp18x-spi.c b/drivers/misc/bmp18x-spi.c
new file mode 100644
index 0000000..d2525b2
--- /dev/null
+++ b/drivers/misc/bmp18x-spi.c
@@ -0,0 +1,143 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * Based on:
+ * BMP085 driver, bmp085.c
+ * Copyright (c) 2010  Christoph Mair <christoph.mair@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/i2c/bmp18x.h>
+
+static int bmp18x_spi_write_byte(void *client, u8 reg, u8 value)
+{
+	u8 data[2] = {reg, value};
+	return spi_write(client, data, 2);
+}
+
+static int bmp18x_spi_read_block(void *client, u8 reg, int len, char *buf)
+{
+	int err = bmp18x_spi_write_byte(client, reg, 0);
+
+	if (err < 0)
+		return err;
+
+	return spi_read(client, buf, len);
+}
+
+static int bmp18x_spi_read_byte(void *client, u8 reg)
+{
+	u8 data;
+	int err = bmp18x_spi_write_byte(client, reg, 0);
+
+	if (err < 0)
+		return err;
+
+	err = spi_read(client, &data, 1);
+	if (err < 0)
+		return err;
+
+	return data;
+}
+
+static const struct bmp18x_bus_ops bmp18x_spi_bus_ops = {
+	.read_block	= bmp18x_spi_read_block,
+	.read_byte	= bmp18x_spi_read_byte,
+	.write_byte	= bmp18x_spi_write_byte
+};
+
+static int __devinit bmp18x_spi_probe(struct spi_device *client)
+{
+	int err;
+	struct bmp18x_data_bus data_bus = {
+		.bops = &bmp18x_spi_bus_ops,
+		.client = client
+	};
+
+	client->bits_per_word = 8;
+	err = spi_setup(client);
+	if (err < 0) {
+		dev_err(&client->dev, "spi_setup failed!\n");
+		return err;
+	}
+
+	return bmp18x_probe(&client->dev, &data_bus);
+}
+
+static void bmp18x_spi_shutdown(struct spi_device *client)
+{
+	bmp18x_disable(&client->dev);
+}
+
+static int bmp18x_spi_remove(struct spi_device *client)
+{
+	return bmp18x_remove(&client->dev);
+}
+
+#ifdef CONFIG_PM
+static int bmp18x_spi_suspend(struct device *dev)
+{
+	return bmp18x_disable(dev);
+}
+
+static int bmp18x_spi_resume(struct device *dev)
+{
+	return bmp18x_enable(dev);
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(bmp18x_spi_pm_ops, bmp18x_spi_suspend, bmp18x_spi_resume);
+
+static const struct spi_device_id bmp18x_id[] = {
+	{ BMP18X_NAME, 0 },
+	{ "bmp085", 0 },
+	{ "bmp180", 0 },
+	{ "bmp181", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(spi, bmp18x_id);
+
+static struct spi_driver bmp18x_spi_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= BMP18X_NAME,
+		.pm	= &bmp18x_spi_pm_ops,
+	},
+	.id_table	= bmp18x_id,
+	.probe		= bmp18x_spi_probe,
+	.shutdown	= bmp18x_spi_shutdown,
+	.remove		= __devexit_p(bmp18x_spi_remove)
+};
+
+static int __init bmp18x_spi_init(void)
+{
+	return spi_register_driver(&bmp18x_spi_driver);
+}
+
+static void __exit bmp18x_spi_exit(void)
+{
+	spi_unregister_driver(&bmp18x_spi_driver);
+}
+
+MODULE_AUTHOR("Eric Andersson <eric.andersson@xxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("BMP18X SPI bus driver");
+MODULE_LICENSE("GPL");
+
+module_init(bmp18x_spi_init);
+module_exit(bmp18x_spi_exit);
diff --git a/include/linux/i2c/bmp18x.h b/include/linux/i2c/bmp18x.h
new file mode 100644
index 0000000..30fa636
--- /dev/null
+++ b/include/linux/i2c/bmp18x.h
@@ -0,0 +1,65 @@
+/*
+ * Copyright (c) 2012  Bosch Sensortec GmbH
+ * Copyright (c) 2012  Unixphere AB
+ *
+ * Based on:
+ * BMP085 driver, bmp085.c
+ * Copyright (c) 2010  Christoph Mair <christoph.mair@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef _BMP18X_H
+#define _BMP18X_H
+
+#define BMP18X_NAME "bmp18x"
+
+/**
+ * struct bmp18x_platform_data - represents platform data for the bmp18x driver
+ * @chip_id: Configurable chip id for non-default chip revisions
+ * @default_oversampling: Default oversampling value to be used at startup,
+ * value range is 0-3 with rising sensitivity.
+ * @temp_measurement_period: Temperature measurement period (milliseconds), set
+ * to zero if unsure.
+ * @init_hw: Callback for hw specific startup
+ * @deinit_hw: Callback for hw specific shutdown
+ */
+struct bmp18x_platform_data {
+	u8	chip_id;
+	u8	default_oversampling;
+	u32	temp_measurement_period;
+	int	(*init_hw)(void);
+	void	(*deinit_hw)(void);
+};
+
+struct bmp18x_bus_ops {
+	int	(*read_block)(void *client, u8 reg, int len, char *buf);
+	int	(*read_byte)(void *client, u8 reg);
+	int	(*write_byte)(void *client, u8 reg, u8 value);
+};
+
+struct bmp18x_data_bus {
+	const struct bmp18x_bus_ops	*bops;
+	void	*client;
+};
+
+int bmp18x_probe(struct device *dev, struct bmp18x_data_bus *data_bus);
+int bmp18x_remove(struct device *dev);
+#ifdef CONFIG_PM
+int bmp18x_enable(struct device *dev);
+int bmp18x_disable(struct device *dev);
+#endif
+
+#endif
-- 
1.7.3.4

--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/


[Other Archives]     [Linux Kernel Newbies]     [Linux Driver Development]     [Fedora Kernel]     [Linux Kernel Testers]     [Linux SH]     [Linux Omap]     [Linux Kbuild]     [Linux Tape]     [Linux Input]     [Linux Kernel Janitors]     [Linux Kernel Packagers]     [Linux Doc]     [Linux Man Pages]     [Linux API]     [Linux Memory Management]     [Linux Modules]     [Linux Standards]     [Kernel Announce]     [Netdev]     [Git]     [Linux PCI]     Linux CAN Development     [Linux I2C]     [Linux RDMA]     [Linux NUMA]     [Netfilter]     [Netfilter Devel]     [SELinux]     [Bugtraq]     [FIO]     [Linux Perf Users]     [Linux Serial]     [Linux PPP]     [Linux ISDN]     [Linux Next]     [Kernel Stable Commits]     [Linux Tip Commits]     [Kernel MM Commits]     [Linux Security Module]     [Filesystem Development]     [Ext3 Filesystem]     [Linux bcache]     [Ext4 Filesystem]     [Linux BTRFS]     [Linux CEPH Filesystem]     [Linux XFS]     [XFS]     [Linux NFS]     [Linux CIFS]     [Ecryptfs]     [Linux NILFS]     [Linux Cachefs]     [Reiser FS]     [Initramfs]     [Linux FB Devel]     [Linux OpenGL]     [DRI Devel]     [Fastboot]     [Linux RT Users]     [Linux RT Stable]     [eCos]     [Corosync]     [Linux Clusters]     [LVS Devel]     [Hot Plug]     [Linux Virtualization]     [KVM]     [KVM PPC]     [KVM ia64]     [Linux Containers]     [Linux Hexagon]     [Linux Cgroups]     [Util Linux]     [Wireless]     [Linux Bluetooth]     [Bluez Devel]     [Ethernet Bridging]     [Embedded Linux]     [Barebox]     [Linux MMC]     [Linux IIO]     [Sparse]     [Smatch]     [Linux Arch]     [x86 Platform Driver]     [Linux ACPI]     [Linux IBM ACPI]     [LM Sensors]     [CPU Freq]     [Linux Power Management]     [Linmodems]     [Linux DCCP]     [Linux SCTP]     [ALSA Devel]     [Linux USB]     [Linux PA RISC]     [Linux Samsung SOC]     [MIPS Linux]     [IBM S/390 Linux]     [ARM Linux]     [ARM Kernel]     [ARM MSM]     [Tegra Devel]     [Sparc Linux]     [Linux Security]     [Linux Sound]     [Linux Media]     [Video 4 Linux]     [Linux IRDA Users]     [Linux for the blind]     [Linux RAID]     [Linux ATA RAID]     [Device Mapper]     [Linux SCSI]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Linux IDE]     [Linux SMP]     [Linux AXP]     [Linux Alpha]     [Linux M68K]     [Linux ia64]     [Linux 8086]     [Linux x86_64]     [Linux Config]     [Linux Apps]     [Linux MSDOS]     [Linux X.25]     [Linux Crypto]     [DM Crypt]     [Linux Trace Users]     [Linux Btrace]     [Linux Watchdog]     [Utrace Devel]     [Linux C Programming]     [Linux Assembly]     [Dash]     [DWARVES]     [Hail Devel]     [Linux Kernel Debugger]     [Linux gcc]     [Gcc Help]     [X.Org]     [Wine]

Add to Google Powered by Linux

[Older Kernel Discussion]     [Yosemite National Park Forum]     [Large Format Photos]     [Gimp]     [Yosemite Photos]     [Stuff]