[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Search Epson Archive

Re: alternative inks, and ink usage



Hey Joe,

Do you think these pads are $35 better than just putting
some regular sponge material in there instead? Does
anything look special about them?

John Richmond
Alpha Electronics
3846 Pipers Crest
San Antonio, Tx 78251
(210) 681-1527
grjr@satx.rr.com

----- Original Message ----- 
From: "Joe Dolice" <tech-man@erols.com>
To: <epson-inkjet@leben.com>
Sent: Wednesday, May 29, 2002 12:15 PM
Subject: Re: alternative inks, and ink usage


> Hi Phil & Marilu,
> I just ordred 2 sets of pads for my 1160 from National Parts Depot.
> Margaret Jones <MJones@nationalparts.com> is very halpful and pleasant
> to deal with. I sent the order via email, and she replied within hours
> that the order was received, gave me an order number and let me know
> that the pads would take about a week to get to them and that she would
> then notify me when they were shipped from NPD to me.
> National Parts Depot's minimum order is $25, so I ordered TWO sets of
> pads. I'm quoting my order here in case you need quantities, numbers,
> etc:
> "8 each Epson ref# 743, Part# 1048802 Porous Pad FL each $0.50 Total
> $4.00; 4 each Epson ref# 752, Part# 1048800 Porous Pad LG each $3.20
> Total $12.80; 4 each Epson ref# 766, Part# 1048801 Porous Pad SM each
> $2.20 Total $ 8.80."
> Above comes to $25.60 + with their shipping and tax, the total billed
> to my CC was $35.83; for me shipped to New York City. Your total may
> vary, of course depending upon where you are located. Personally, I 
> always try to get a service manual for any equipment before I tear into
> it, and one is available also through them. FYI, the Epson part # for
> the Service Manual for the 1160 is "TM-SC860/1160", and if I recall
> correctly it cost around $21. You might be able to get one cheaper from
> anothr source, but I have found Margaret Jones at NPD so helpful in
> responding to my inquiries that I order from them exclusively. Hope this
> is of help.
> Joe D.      
> 
> Phil & Marilu Morse wrote:
> > 
> > Hello Larry,
> > 
> > Here is the procedure I used yesterday to successfully reset my 1160.  I am
> > sorry I cannot credit the orignal author or list where I found this as I had
> > saved only the procedure body of the message.  My apologies and thanks to
> > the original author for his concise work.
> > 
> > 1. Turn the printer off using the power button on the panel of the
> > printer.
> > 2. Disconnect the interface cable at the back of the printer.
> > 3. Hold down the 'LOAD/EJECT' and 'CLEANING' buttons simultaneously.
> > 4. Turn the printer on. Release all buttons as soon as paper out light
> > flashes.
> > 5. Quickly press the 'LOAD/EJECT' button while paper out light is
> > flashing.
> > 6. Release the button and the printer will initialize.
> > 7. Once initialization is complete, turn the printer off.
> > 8. Reconnect the interface cable.
> > 9. Turn the printer on and try to print a document.
> > 
> > Now can anyone tell me where I can purchase 1160 waste ink pads?
> > 
> > Phil
> > 
> > ----- Original Message -----
> > From: "Larry Buzzell" <melarry@gci.net>
> > 
> > > Turned on power, and the lights remain blinking on/off....................
> > > ........My reset procedure isn't staying stuck!
> > >
> > > Larry
> > 
> > -
> > Turn off HTML mail features. Keep quoted material short. Use accurate
> > subject lines. http://www.leben.com/lists for list instructions.
> -
> Turn off HTML mail features. Keep quoted material short. Use accurate
> subject lines. http://www.leben.com/lists for list instructions.
-
Turn off HTML mail features. Keep quoted material short. Use accurate
subject lines. http://www.leben.com/lists for list instructions.

[Photo]     [Photo Printers]     [Yosemite News]    [Yosemite Photos]    [Scanner Discussion Archive]     [Free Online Dating]     [Gimp]     [Deep Creek Hot Springs]     [Photo Sharing]     [Linux Power Management]     [Gimp Users]

Powered by Linux