On 02/14/2012 11:15 AM, Dan Barber wrote:
> On 02/14/2012 09:33 AM, Dan Barber wrote:
>>> Steven,
>>>
>>> Thanks for the reply, my apologies that my first response was sent
>>> directly to you. I am running "/etc/init.d/corosync start" as root, do I
>>> need to do something else to make sure that corosync runs as root? I get
>>> the same behavior from running "service corosync start" run as root,
>>> which is understandable as I believe those are essentially identical
>>> operations.
>>>
>>
>>No problem. Also please don't top post - it makes following the threads
>>difficult for followup readers of the thread archive.
>>
>>Which OS are you using? If RHEL/Fedora/centos, do you have selinux
> enabled?
>>
>>Can you run corosync-blackbox?
>
> Steve,
>
> Thanks again for the help, both on list protocol and the questions. It
> looks like it is
> a selinux problem, I am running on centos. I'm working with our linux
> folks to try and
> start making progress again, selinux isn't supposed to be enabled.
>
> Thanks!
>
> Dan
>
Note RHEL works fine with all current supported z streams for corosync
with selinux. Not sure in the centos case (that distro may not have
picked up the appropriate z stream packages).
Regards
-steve
>>
>>> Thanks,
>>>
>>> Dan
>>>
>>> ------------------------------------------------------------------------
>>> *From:* Steven Dake <sdake@xxxxxxxxxx>
>>> *To:* Dan Barber <dandy_dan_1999@xxxxxxxxx>
>>> *Cc:* "discuss@xxxxxxxxxxxx" <discuss@xxxxxxxxxxxx>
>>> *Sent:* Tuesday, February 14, 2012 9:19 AM
>>> *Subject:* Re: Problems starting up Corosync
>>>
>>> On 02/14/2012 09:16 AM, Dan Barber wrote:
>>>> I am having problems bringing up Corosync and hoping someone will see
>>>> the stupid mistake that I’ve made. I’ve done a lot of searching for the
>>>> error that I’m seeing, and haven’t found anything other than a reference
>>>> to the line of the code which produces this error, which concerns me a
>>>> little.
>>>>
>>>> Here’s the corosync.conf file that I’m using:
>>>> # Please read the corosync.conf.5 manual page
>>>> compatibility: whitetank
>>>>
>>>> totem {
>>>> version: 2
>>>> secauth: off
>>>> threads: 0
>>>> interface {
>>>> ringnumber: 0
>>>> bindnetaddr: 10.47.12.0
>>>> mcastaddr: 226.94.1.1
>>>> mcastport: 4000
>>>> ttl: 1
>>>> }
>>>> }
>>>>
>>>> logging {
>>>> fileline: off
>>>> to_stderr: no
>>>> to_logfile: yes
>>>> to_syslog: yes
>>>> logfile: /var/log/cluster/corosync.log
>>>> debug: on
>>>> timestamp: on
>>>> logger_subsys {
>>>> subsys: AMF
>>>> debug: off
>>>> }
>>>> }
>>>>
>>>> amf {
>>>> mode: disabled
>>>> }
>>>>
>>>> And here is corosync.log from start up to the failure lines:
>>>> Feb 13 09:45:36 corosync [MAIN ] Corosync Cluster Engine ('1.4.1'):
>>>> started and ready to provide service.
>>>> Feb 13 09:45:36 corosync [MAIN ] Corosync built-in features: nss dbus
>>>> rdma snmp
>>>> Feb 13 09:45:36 corosync [MAIN ] Successfully read main configuration
>>>> file '/etc/corosync/corosync.conf'.
>>>> Feb 13 09:45:36 corosync [TOTEM ] Token Timeout (1000 ms) retransmit
>>>> timeout (238 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] token hold (180 ms) retransmits before
>>>> loss (4 retrans)
>>>> Feb 13 09:45:36 corosync [TOTEM ] join (50 ms) send_join (0 ms)
>>>> consensus (1200 ms) merge (200 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] downcheck (1000 ms) fail to recv const
>>>> (2500 msgs)
>>>> Feb 13 09:45:36 corosync [TOTEM ] seqno unchanged const (30 rotations)
>>>> Maximum network MTU 1402
>>>> Feb 13 09:45:36 corosync [TOTEM ] window size per rotation (50 messages)
>>>> maximum messages per rotation (17 messages)
>>>> Feb 13 09:45:36 corosync [TOTEM ] missed count const (5 messages)
>>>> Feb 13 09:45:36 corosync [TOTEM ] send threads (0 threads)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP token expired timeout (238 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP token problem counter (2000 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP threshold (10 problem count)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP multicast threshold (100 problem
>>>> count)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP automatic recovery check timeout
>>>> (1000 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] RRP mode set to none.
>>>> Feb 13 09:45:36 corosync [TOTEM ] heartbeat_failures_allowed (0)
>>>> Feb 13 09:45:36 corosync [TOTEM ] max_network_delay (50 ms)
>>>> Feb 13 09:45:36 corosync [TOTEM ] HeartBeat is Disabled. To enable set
>>>> heartbeat_failures_allowed > 0
>>>> Feb 13 09:45:36 corosync [TOTEM ] Initializing transport (UDP/IP
>>> Multicast).
>>>> Feb 13 09:45:36 corosync [TOTEM ] Initializing transmit/receive
>>>> security: libtomcrypt SOBER128/SHA1HMAC (mode 0).
>>>> Feb 13 09:45:36 corosync [IPC ] you are using ipc api v2
>>>> Feb 13 09:45:36 corosync [TOTEM ] Unable to bind the socket to receive
>>>> multicast packets: Permission denied (13)
>>>> Feb 13 09:45:36 corosync [TOTEM ] Could not set traffic priority: Socket
>>>> operation on non-socket (88)
>>>>
>>>> The last two lines are the source of the problem, at least as far as I
>>>> can tell. This results in LOTS of these lines as Corosync continues to
>>>> try working:
>>>> Feb 13 09:45:44 corosync [TOTEM ] sendmsg(mcast) failed (non-critical):
>>>> Socket operation on non-socket (88)
>>>>
>>>> I’m hopeful someone will be able to quickly point out the absolutely
>>>> stupid mistake that I’m making.
>>>>
>>>> Thanks so much!
>>>>
>>>> Dan Barber
>>>>
>>>>
>>>
>>> corosync must be run as root.
>>>
>>> Regards
>>> -steve
>
>
>
> _______________________________________________
> discuss mailing list
> discuss@xxxxxxxxxxxx
> http://lists.corosync.org/mailman/listinfo/discuss
_______________________________________________
discuss mailing list
discuss@xxxxxxxxxxxx
http://lists.corosync.org/mailman/listinfo/discuss
[Corosync Project]
[Linux USB Devel]
[Video for Linux]
[Linux Audio Users]
[Photo]
[Yosemite News]
[Yosemite Photos]
[Free Online Dating]
[Linux Kernel]
[Linux SCSI]
[XFree86]
