Re: Setting up a pci passthrough device

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]


On Mon, February 6, 2012 18:05, Ken Bass wrote:
> Take a look at http://wiki.xensource.com/xenwiki/VTdHowTo
>
> Two things in particular about PCI passthrough:
>
> - Only devices with FLR capabilities are supported.
> - Some motherboards are buggy. They advertised that they
> support Vt-d
> but do not correctly handle it (those with a broken ACPI
> DMAR table)
>
> I think lspci -vv will tell you if the device supports
> FLR. It will show
> 'FLReset+' I believe.
>
03:00.0 Serial controller: Oxford Semiconductor Ltd
OX16PCI954 (Quad 16950 UART) function 0 (Uart) (prog-if 06
[16950])
        Subsystem: Oxford Semiconductor Ltd Device 0000
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr-
DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR-
<PERR- INTx-
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at d040 [size=32]
        Region 1: Memory at d0702000 (32-bit,
non-prefetchable) [size=4K]
        Region 2: I/O ports at d020 [size=32]
        Region 3: Memory at d0701000 (32-bit,
non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0
DScale=0 PME-
        Kernel driver in use: serial


No FLR string is present.  So pci pass through is a dead
end I take it?


I increased the number of uarts available to the host
system at boot with the 8250.nr_uarts=10 option.  This
gives me the following:

# setserial -g /dev/ttyS*
/dev/ttyS0, UART: 16550A, Port: 0x03f8, IRQ: 4
/dev/ttyS1, UART: unknown, Port: 0x02f8, IRQ: 3
/dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4
/dev/ttyS3, UART: unknown, Port: 0x02e8, IRQ: 3
/dev/ttyS4, UART: 16950/954, Port: 0xd040, IRQ: 17
/dev/ttyS5, UART: 16950/954, Port: 0xd048, IRQ: 17
/dev/ttyS6, UART: 16950/954, Port: 0xd050, IRQ: 17
/dev/ttyS7, UART: 16950/954, Port: 0xd058, IRQ: 17
/dev/ttyS8, UART: unknown, Port: 0x0000, IRQ: 0
/dev/ttyS9, UART: unknown, Port: 0x0000, IRQ: 0

With this change I now can add one serial port
(/dev/ttyS4) to a virtual guest using virt-manager and
have the guest start, but no more than one.  Any more that
one and the guest fails to run with the same irq conflict
error as before.  I still have not tried to see if the
serial port actually works in this case, just that the
system starts.

I ran across this thread relating to serial devices in
qemu from some time ago:

http://www.mail-archive.com/qemu-devel@xxxxxxxxxx/msg27354.html

Which seems to me to imply that it is not possible for a
qemu guest to have more than 2 serial ports, one of which
I gather has to be the console.

However, this statement attracted my attention:

> This is wrong. Two devices should never be manipulating
> the same qemu_irq object.  If you want multiple devices
> connected to the same IRQ then you need an explicit
> multiplexer. e.g. arm_timer.c:sp804_set_irq.

And in a later message in the same thread:

> Two devices have the same s->irq. Give each on its own
> qemu_irq, and feed it into a multiplexer that ORs them
> together and sends the result to the interrupt
> controller's qemu_irq:


Is there a way to set irqs in quem to map to specific
ports on a pci card as this seems to imply?  How is it
done?




-- 
***          E-Mail is NOT a SECURE channel          ***
James B. Byrne                mailto:ByrneJB@xxxxxxxxxxxxx
Harte & Lyne Limited          http://www.harte-lyne.ca
9 Brockley Drive              vox: +1 905 561 1241
Hamilton, Ontario             fax: +1 905 561 0757
Canada  L8E 3C3

_______________________________________________
CentOS-virt mailing list
CentOS-virt@xxxxxxxxxx
http://lists.centos.org/mailman/listinfo/centos-virt


[CentOS Users]     [Linux Media]     [Asterisk]     [Photo]     [DCCP]     [Netdev]     [Xorg]     [Xfree86]     [Devices]     [Linux USB]

Powered by Linux Add to Google