Sent by: linux-arm-bounces@xxxxxxxxxxxxxxxxxxx
Date: 11/05/2009 08:07PM
cc: linux-arm@xxxxxxxxxxxxxxxxxxx
Subject: Re: Reg Linux-2.6.27 hang
Hi Prabha,
Please pay attention to the EABI configure option.
2009/11/2 Prabha J <prabha.j@xxxxxxx>:
>
> Hi ,
>
> we are porting linux 2.6.27 on imx27 based platform. we did all the platform
> dependent changes .
>
> With this linux is booting till a point and stopping there ..
>
> stopping at
>
> (VFS) Mounting file system
> Freeing init memory
>
> While debugging through printk we could go till
>
> rest_init() -> kernel _init() -> init_post() --->
>
> Going for opening initial console . .... using sys_open() .... After that no
> prints .......
>
>
> Can any body help us to go forward ?
>
> Thanks in advance ,
> Prabha
>
>
> Please see the following logs ..
>
> Launch LinuxUncompressing
> Linux......................................................................
> done, booting the kernel.
> Linux version 2.6.28-arm2 (root@xxxxxxxxxxxxxxxxxxxxx) (gcc version 4.1.1)
> #75 Wed Oct 28 13:12:53 IST 2009
> CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177
> CPU: VIVT data cache, VIVT instruction cache
> Machine: Freescale i.MX27ADS
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
> Kernel command line: root=/dev/ram rw mem=64M console=ttymxc0,115200
> MXC GPIO hardware
> MXC IRQ initialized
> PID hash table entries: 256 (order: 8, 1024 bytes)
>
> Clock input source is 26000000
>
> After for loop
> test1
> CCM_PCCR1 = fe5aef88
> b4 spll_clk.disableConsole: colour dummy device 80x30
> Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Memory: 64MB = 64MB total
> Memory: 60780KB available (1956K code, 252K data, 92K init)
> Calibrating delay loop... 132.71 BogoMIPS (lpj=663552)
> Security Framework initialized
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> kernel thread started : M.V<5>SCSI subsystem initialized
> checking if image is initramfs...it isn't (no cpio magic); looks like an
> initrd
> do_sys_open entry<6>Freeing initrd memory: 1792K
> NetWinder Floating Point Emulator V0.97 (extended precision)
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> JFS: nTxBlock = 489, nTxLock = 3914
> msgmni has been set to 122
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Serial: IMX driver
> imx-uart.0: ttymxc0 at MMIO 0x1000a000 (irq = 20) is a IMX
> console [ttymxc0] enabled
> imx-uart.1: ttymxc1 at MMIO 0x1000b000 (irq = 19) is a IMX
> imx-uart.2: ttymxc2 at MMIO 0x1000c000 (irq = 18) is a IMX
> imx-uart.3: ttymxc3 at MMIO 0x1000d000 (irq = 17) is a IMX
> imx-uart.4: ttymxc4 at MMIO 0x1001b000 (irq = 49) is a IMX
> imx-uart.5: ttymxc5 at MMIO 0x1001c000 (irq = 48) is a IMX
> brd: module loaded
> loop: module loaded
> st: Version 20080504, fixed bufsize 32768, s/g segs 256
> Driver 'st' needs updating - please use bus_type methods
> Driver 'sd' needs updating - please use bus_type methods
> drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
> do_sys_open entrydo_sys_open entry<5>RAMDISK: Compressed image found at
> block 0
> EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
> VFS: Mounted root (ext2 filesystem).
> Freeing init memory: 92K
>
>
> After this some junk characters are coming like ....
>
> ��֍�򁰠0^ޝ��r�'���ϊ��r:�������:��M� ��D�d�z ?��
> Τ��8V�`�Т���V잊]nn]^ｸ�m8m��^� �m� E��N��8��6���:]���
>
>
>
>
>
