pxa270 colibri no USB device detect with 2.6.22 Kernel

["Maik Steuer" <Maik.Steuer@xxxxxx>]

Hello,

is their any problem with usb support for toradex colibri pxa270 with 2.6.22 kernel?

No device will be detect.

Is it possible, that my kernel can´t found the usb-hub?

here is the output while booting

Linux version 2.6.22 (root@pcb50) (gcc version 4.0.0 (DENX ELDK 4.1 4.0.0)) #11 Mon Apr 7 15:02:16 CEST 2008
CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=0000397f
Machine: Toradex Colibri Module
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Run Mode clock: 208.00MHz (*16)
Turbo Mode clock: 312.00MHz (*1.5, active)
Memory clock: 208.00MHz (/2)
System bus clock: 208.00MHz 
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/nfs ip=:::::eth0: console=ttyS0,9600n8
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 62080KB available (2512K code, 217K data, 96K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: pxa_timer clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
loop: module loaded
usbcore: registered new interface driver ub
dm9000 Ethernet Driver
eth0: dm9000 at f1000000,f1000004 IRQ 146 MAC: 00:14:2d:00:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Probing Colibri flash at physical address 0x00000000 (32-bit buswidth)
Colibri flash: Found 2 x16 devices at 0x0 in 32-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 3 MTD partitions on "Colibri flash":
0x00000000-0x00080000 : "Bootloader"
0x00080000-0x00480000 : "Kernel"
0x00480000-0x02000000 : "Filesystem"
Colibri PCMCIA
usbmon: debugfs is not available
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
Colibri MMC/SD setup <6>done.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1
XScale iWMMXt coprocessor detected.
pccard: PCMCIA card inserted into slot 0
pcmcia: registering new device pcmcia0.0
eth0: link down
hda: SAMSUNG CF/ATA, CFA DISK drive
Sending BOOTP requests .<6>eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
. OK
IP-Config: Got BOOTP answer from 192.168.1.1, my address is 192.168.1.99
IP-Config: Complete:
      device=eth0, addr=192.168.1.99, mask=255.255.255.0, gw=192.168.1.1,
     host=COLIBRI6597, domain=development.local, nis-domain=(none),
     bootserver=192.168.1.1, rootserver=192.168.1.1, rootpath=/project/fs
hdb: no response (status = 0xa1), resetting drive
hdb: no response (status = 0xa1)
ide0 at 0xc4860000-0xc4860007,0xc486000e on irq 9
hda: max request size: 128KiB
hda: 253952 sectors (130 MB) w/1KiB Cache, CHS=496/16/32
 hda:<7>driver_probe_done: probe_count = 2
 hda1
ide-cs: hda: Vpp = 0.0
Looking up port of RPC 100003/2 on 192.168.1.1
Looking up port of RPC 100005/1 on 192.168.1.1
VFS: Mounted root (nfs filesystem).
Freeing init memory: 96K

init started:  BusyBox v1.00 (2004.11.26-02:54+0000) multi-call binary


BusyBox v1.00 (2004.11.26-02:54+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.


Processing /etc/profile... Done
[root@Linux /]#

I nerver found some additional information. So i hope somebody can help me.

thanks
Maik
-- 
Psst! Geheimtipp: Online Games kostenlos spielen bei den GMX Free Games! 
http://games.entertainment.gmx.net/de/entertainment/games/free

-- 
GMX startet ShortView.de. Hier findest Du Leute mit Deinen Interessen!
Jetzt dabei sein: http://www.shortview.de/?mc=sv_ext_mf@gmx

-------------------------------------------------------------------
List admin: http://lists.arm.linux.org.uk/mailman/listinfo/linux-arm
FAQ:        http://www.arm.linux.org.uk/mailinglists/faq.php
Etiquette:  http://www.arm.linux.org.uk/mailinglists/etiquette.php