Re: [PATCH] ARM: tegra: add device tree for SHIELD

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 02/25/2014 03:53 AM, Stephen Warren wrote:
On 02/24/2014 03:26 AM, Alexandre Courbot wrote:
Add a device tree for NVIDIA SHIELD. The set of enabled features is
still minimal with no display option (although HDMI should be easy
to get to work) and USB requiring external power.

You could add a simple-framebuffer node for now, I think?

That would not be useful I'm afraid, since the DSI clocks will be switched off in the absence of a dsi DT node in host1x, so you would end up with a blank screen. Our best shot at display for the moment would be HDMI, but I need to spend some more time on it.

Proper internal panel support would require a panel driver with the proper DSI initialization sequences. It is in my pipe.

diff --git a/arch/arm/boot/dts/tegra114-roth.dts b/arch/arm/boot/dts/tegra114-roth.dts

+	memory {
+		reg = <0x80000000 0x79600000>;

It might be worth a comment here pointing out that the rest of RAM is
reserved for some carveouts/..., or at least that these values are set
this way in order to match what the bootloader usually passes to
downstream kernels in the command-line?

Yes, absolutely right. On a more general note I feel like DTs could gain clarity if they had more comments (e.g. for pinmuxing which are a quite heavy block otherwise), do you have any objection to this? (I guess not, but so far the rule seems to be "no comment in DT" :P )


+	i2c@7000d000 {

+		palmas: pmic@58 {
+			compatible = "ti,palmas";
+			reg = <0x58>;
+			interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
+			ti,irq-externally-inverted;

Unfortunately, the patch I sent to document/implement that last property
hasn't yet been ack'd/applied, so I'll hold off applying this until it has.

That's fine, I wanted to avoid sending another patch soon after just for that particular change.


+	/* Wifi */
+	sdhci@78000000 {
+		status = "okay";
+		bus-width = <4>;
+		broken-cd;
+		keep-power-in-suspend;
+		cap-sdio-irq;

Is non-removable better than broken-cd, or are they entirely unrelated?

They are unrelated actually. With non-removable the driver expects the device to always be there since boot, and does not check for the card to be removed/added after boot. broken-cd indicates there is no CD line and the device should be polled regularly.

For the Wifi chip, non-removable would be the correct setting hardware-wise, but there is a trap: the chip has its reset line asserted at boot-time, and you need to set GPIO 229 to de-assert it. Only after that will the device be detected on the SDIO bus. Since it lacks a CD line, it must be polled, hence the broken-cd property.

This also raises another, redundant problem with DT bindings: AFAIK we currently have no way to let the system know the device will only appear after a given GPIO is set. It would also be nice to be able to give some parameters to the Wifi driver through the DT (like the OOB interrupt). Right now the Wifi chip is brought up by exporting the GPIO and writing to it from user-space, and the OOB interrupt is not used.

Otherwise, Wifi works great with the brcmfmac driver and NVRAM file extracted from Android.

Should we add broken-cd and/or cap-sdio-irq to the SDIO WiFi on other
boards (Springbank, Ventana, Cardhu)?

If they don't have the GPIO requirement that SHIELD has, I don't think it is necessary. non-removable is probably a better property for soldered Wifi chips.

I'm not sure about cap-sdio-irq, it doesn't seem to make a difference for SHIELD Wifi.


+	usb-phy@7d000000 {
+		status = "okay";
+		nvidia,xcvr-setup = <7>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+		dr_mode = "otg";

While opt is probably accurate, we don't actually support otg upstream,
but only host. While the DT is supposed to represent HW rather than
SW/OS details, I've tried to avoid putting otg into the DT, since I'm
not sure that the DT binding for otg is stable, since we can't test it,
whereas host probably is. Still, this is a pretty minor detail, and we
can ignore that if you want ("otg" evidently /works/ fine on Seaboard,
so it's OK if you keep this).

The setting works for me and the binding is documented, so maybe we can keep it as-is?

Thanks for the review - v2 will be on the way, as well as Tegra Note 7 hopefully.

Alex.


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [CentOS ARM]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]     [Photos]