Re: [PATCH 3/3] ARM: OMAP2+: Fix eMMC on n900 with device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Tony,

On Thu, Nov 21, 2013 at 10:51:06AM -0800, Tony Lindgren wrote:
> Looks like we need to configure the regulators and use the pdata
> quirk to make eMMC work with device tree.
> 
> It seems that mostly vmmc2 is used, and only some earlier revisions
> like the macro board used vaux3.
> 
> Note that we can add support for the macro board later as needed
> by including the common n900 .dts file and configuring the vaux3
> instead of vmmc2, and adding support for the smc91x Ethernet.
>
> ---
> 
> Can you guys please test this on production n900 devices?
> 
> I've tested it with my old macro board where I had to patch in vaux3
> instead of vmmc2. I think there's some confusion in the legacy code
> comments, or else I'm confused. In any case, vaux3 works for the macro
> board, and I suspect that the production versions have vmmc2.
> 
> If this does not work and vaux3 as regulator works, please also dump
> out the system_rev from your board.

The good news is, that I got eMMC working :) The bad news is, that it
did not work with your patch :( I included my DTS nodes below. The
phone is HW/System revision 0x2101.

I have a second N900, which has HW revision 0x2204. I did not yet test
the patch with this phone, but legacy code also seems to use vaux3 for
it. Seems like we need two n900.dts files?

--- DTS nodes working on the 0x2101 board ---

&omap3_pmx_core {
	mmc2_pins: pinmux_mmc2_pins {
		pinctrl-single,pins = <
			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk */
			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd */
			0x12c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc2_dat0 */
			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1 */
			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2 */
			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3 */
			0x134 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat4 */
			0x136 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat5 */
			0x138 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat6 */
			0x13a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat7 */
		>;
	};
};

&mmc2 {
    pinctrl-names = "default";
    pinctrl-0 = <&mmc2_pins>;

    vmmc-supply = <&vaux3>;
    vmmc_aux-supply = <&vsim>;
    bus-width = <8>;
    non-removable;
};

-- Sebastian

Attachment: signature.asc
Description: Digital signature

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [CentOS ARM]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]     [Photos]